Hotpoint HDA2160HSS Manual

Hotpoint Vaskemaskine HDA2160HSS

Læs gratis den danske manual til Hotpoint HDA2160HSS (32 sider) i kategorien Vaskemaskine. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Hotpoint HDA2160HSS, eller vil du spørge andre brugere om produktet?

Side 1/32
READ CAREFULLY
KEEP THESE INSTRUCTIONS
CHECK THE FOLLOWING
Dishwasher is square and level at both the top and
bottom of the cabinet opening, with no twisting or
distortion of the tub or door.
All 4 legs of the dishwasher are firmly in contact with
the floor.
Drain hose is not pinched between the dishwasher
and adjacent cabinets or walls.
FOR YOUR SAFETY
Read and observe all WARNINGS and CAUTIONS
shown throughout these instructions.
While performing installations described in this
booklet, gloves, safety glasses or goggles should
be worn.
IMPORTANT – Observe all governing codes and
ordinances.
Note to Installer – Be sure to leave these instructions
for the consumer’s and local inspector’s use.
– Keep these instructions with Note to Consumer
your Owner’s Manual for future reference.
– Installation of this dishwasher requires Skill Level
basic mechanical, electrical and plumbing skills.
Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the Warranty. See Warranty
information.
. New installations Completion Time – 1 to 3 Hours
require more time than replacement installations.
IMPORTANT – The dishwasher MUST be installed to
allow for future removal from the enclosure if service is
required.
Care should be exercised when the appliance is installed
or removed,
to reduce the likelihood of damage to the
power supply cord.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories – See the Owner’s Manual for
available custom panel kits.
Your dishwasher is a water heating appliance.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
31-31587-2 02-19 GEA
Remove all power leading to the appliance from the
circuit breaker or fuse box before beginning installation.
Failure to do so can result in a risk of electrical shock.
To reduce the risk of electric shock, fire, or injury to persons,
the installer must ensure that the dishwasher is completely
enclosed at the time of installation.
The improper connection of the equipment grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service representative
if you are in doubt that the appliance is properly
grounded. If house wiring is not 2-wire with ground, a
ground must be by the installer. When house wiring
is aluminum, be sure to use UL-Listed anti-oxidant
compound and aluminum-to-copper connectors.
To reduce the risk of electric shock, fire, or injury to
persons, the installer should check to ensure that wires are
not pinched or damaged, the house wiring is attached to the
junction box bracket through a strain relief, and all electrical
connections made at the time of install (wire nuts) are
contained inside of
the junction box cover.
WARNING
Retire todos los conductores de corriente del
electrodoméstico de disyuntor o de la caja del fusible
antes de comenzar con la instalación. Si no cumple con
esto, se pod producir el riesgo de descargas eléctricas.
Para reducir el riesgo de descarga eléctrica, incendio
o lesiones a personas, el instalador debe asegurarse
de que el lavaplatos esté completamente cerrado en
el momento de la instalación.
La conexión inadecuada del conductor de conexión a
tierra del equipamiento puede provocar un riesgo de
descarga eléctrica. Consulte a un electricista calificado
o representante de servicio técnico si tiene dudas
sobre la correcta conexión a tierra del aparato. Si el
cableado doméstico no cuenta con un cable de 2 hilos
con conexión a tierra, un instalador debe realizar una
conexión a tierra. Cuando el cableado doméstico es de
aluminio, asegúrese de usar un compuesto antioxidante
y conectores de aluminio a cobre aprobados por UL.
Para reducir el riesgo de descarga eléctrica, incendio
o lesiones a personas, el instalador debe realizar un
control para asegurar que los cables no estén pellizcados
ni dañados, que el cableado del hogar esté conectado a la
ficha de la caja de empalmes a través de un amortiguador
de refuerzo, y que todas las conexiones eléctricas
realizadas en el momento de la instalación (tuercas para
cables) estén dentro de la tapa de la caja de empalmes.
ADVERTENCIA
See your Owner’s Manual for details on how to contact us regarding installation questions
Built-In & Spacemaker®
Dishwashers
Installation
Instructions
PARTS SUPPLIED IN
INSTALLATION PACKAGE:
Two 8-18 x 5/8” Phillips-head wood screws
#10 hex head screw and junction box cover
Drain hose (78” long)
Hose clamp
Literature, product samples and/or coupons
TOOLS YOU WILL NEED:
Phillips-head screwdriver
1/4” and 5/16nutdriver
6” Adjustable wrench
Level
Carpenter’s square
Measuring tape
Safety glasses
Flashlight
Bucket to catch water when flushing the line
15/16” socket (optional for skid removal)
Gloves
Pliers
For New Installations Only:
Tubing cutter
Drill and appropriate bits
Hole saw set
MATERIALS YOU WILL NEED:
WX09X70910 or WX09X70911 power cord if
applicable to your installation, or electrical cable
UL-Listed wire nuts (3)
Thread seal tape
9elbow (¾” hose internal thread on one end,
opposite end sized to fit water supply)
GPF65 Side-mount bracket kit for use with granite
countertops
For New Installations Only:
Electrical cable
Water line–3/8” minimum copper tubing (including
ferrule and compression nut)
Strain relief for electrical connection
Hand shut-off valve (recommended)
Air gap for drain hose, if required
Waste tee for house plumbing, if applicable
GPF10S drain hose (10’ long), if needed
Screw-type hose clamps
Cord protector (power cord models only
as needed)
Conversion leads (power cord models only
as needed)
Installation Preparation
2
Hole Saw Set
Measuring Tape
Tubing Cutter Drill and Bits
Phillips-Head
Screwdriver
15/16” Socket
1/4” and 5/16”
Nutdriver
Bucket
Flashlight
Gloves
Carpenter’s
Square
Safety Glasses
Level
Pliers
6” Adjustable
Wrench
78" Drain Hose
#8
Phillips-Head
Wood Screws
5/8" long
Screw Kit
#10
Hex Head
Junction Box Screw
1/2" long
Cord Protector
- Optional -
(Power Cord
Models Only)
Conversion Leads
WD21X10107
- Optional -
(Power Cord
Models Only)
Thread
Seal Tape
3 Wire Nuts
Hot Water Line–3/8"
Minimum Copper Tubing
Electrical Cable
or WR09X70910 or
WX09X70911 Power Cord
Screw-Type
Hose Clamps
Strain Relief Shut-Off
Valve
GPF65 Side-Mount
Bracket Kit
Optional 10'
Drain Hose
GPF10S
Waste Tee
Coupler for optional
drain hose
90° Elbow
Air
Gap
Hose Clamp Literature
Junction
Box Cover


Produkt Specifikationer

Mærke: Hotpoint
Kategori: Vaskemaskine
Model: HDA2160HSS

Har du brug for hjælp?

Hvis du har brug for hjælp til Hotpoint HDA2160HSS stil et spørgsmål nedenfor, og andre brugere vil svare dig