Hotpoint NWXR483EGWW Manual

Hotpoint Tørretumbler NWXR483EGWW

Læs gratis den danske manual til Hotpoint NWXR483EGWW (8 sider) i kategorien Tørretumbler. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Hotpoint NWXR483EGWW, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Installation

Instructions

Electric Dryer

TOOLS YOU

WILL NEED

MATERIALS YOU WILL NEED

PHILLIPS SCREWDRIVER

SLIP JOINT PLIERS

LEVEL

GLOVES

SAFETY

GLASSES

DRYER POWER

CORD KIT

(NOT PROVIDED

WITH DRYER)

4" DUCT

CLAMPS (2)

4" SPRING

CLAMPS (2)

EXHAUST

HOOD

NOTE: Installation and service of this dryer requires basic

mechanical and electrical skills. It is your responsibility to

contact a qualified installer to make the electrical connections.

3/4" STRAIN

RELIEF

UL RECOGNIZED

4" DIA. METAL

ELBOW

Step 1 Prepare the Area and Exhaust for Installation of

New Dryer (see section 1).

Step 2 Check and Ensure the Existing External Exhaust is

Clean (see section 1) and Meets Attached Installation

Speciﬁcations (see section 3).

Step 3 Remove the Foam Shipping Pads (see section 1).

Step 4 Move the Dryer to the Desired Location.

Step 5 Connect the Power Supply (see section 2).

Step 6 Connect the External Exhaust (see section 4).

Step 7 Level Your Dryer (see section 5).

Step 8 Check the Operation of the Power Supply

and Venting.

Step 9 Place the Owners Manual and the Installation

Instructions in a Location Where They Will Be

Noticed By the Owner.

For Alcove or Closet Installation, see section 6.

For Bathroom or Bedroom Installation, see section 7.

For Mobile or Manufactured Home see, section 8.

For side or bottom exhaust, see section 9.

4" DIA. FLEXIBLE METAL (SEMI-RIGID)

UL LISTED TRANSITION DUCT

(IF NEEDED)

KIT WX08X10077 (INCLUDES 2 ELBOWS)

4" DIA. METAL DUCT

(RECOMMENDED)

4" DIA. FLEXIBLE METAL (FOIL TYPE)

UL LISTED TRANSITION DUCT

(IF NEEDED.)

FLAT BLADE SCREWDRIVER

DUCT TAPE

WARNING RISK OF FIRE

• To reduce the risk of severe injury or death, follow all installation instruc-

tions.

• Clothes dryer installation must be performed by a qualified installer.

• Install the clothes dryer according to these instructions and in accordance

with local codes.

• This dryer must be exhausted to the outdoors.

• Use only 4” rigid metal ducting for exhausting the clothes dryer to the

outdoors.

• Do not install or store this appliance in any location where it could be

exposed to water and or weather.

• Save these instructions. (Installers: Be sure to leave these instructions with

the customer).

• DO NOT install a clothes dryer with flexible plastic ducting materials. If

flexible metal (semi-rigid or foil-type) duct is installed, it must be UL listed

and installed in accordance with the instructions found in "Connecting The

Dryer To House Vent" on page 5 of this manual. Flexible venting materials

are known to collapse, be easily crushed, and trap lint. These conditions will

obstruct dryer airflow and increase the risk of fire.

Questions on Installation? Call: 1-800-GECARES (US)

www.GEAppliances.com (US)

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

•IMPORTANT- Save these

instructions for local inspector’s use.

•IMPORTANT- Observe

all governingcodes and ordinances.

• Note to Installer - Be sure to leave these

instructions with e omth cust er.

• Note to Customer - Keep these instruct-

ions with your Use and Care Book for

future reference.

• Before the old dryer is removed from

service or discarded, remove the dryer

door.

• Service information and the wiring dia-

•

gram are located in the control console.

• Do not allow children on or in the appli-

ance. Close supervision of children is

necessary when the appliance is used

near children.

Install the dryer where the temperature

is above 50°F for satisfactory operation of

the dryer control system.

UL RATED

120/240V,30A

WITH 3 OR 4 PRONGS.

IDENTIFY THE PLUG

TYPE AS PER THE

HOUSE RECEPTACLE

BEFORE PURCHASING

LINE CORD.

Installation Instructions

1 PREPARING FOR INSTALLATION

OF NEW DRYER

Minimum Clearance Other Than Alcove or Closet Installation

Minimum clearance to combustible surfaces and for air opening are: 0 in. clearance both sides and 1 in. rear. Consideration

must be given to provide adequate clearance for installation and service.

2 ELECTRICAL CONNECTION

INFORMATION

TIP: Install your dryer before installing your washer.

This will allow better access when installing dryer exhaust.

REMOVING LINT FROM WALL

EXHAUST OPENING

TILT THE DRYER SIDEWAYS

AND REMOVE THE FOAM

SHIPPING PADS BY

PULLING AT THE SIDES

AND BREAKING THEM

AWAY FROM THE DRYER

LEGS. BE SURE TO

REMOVE ALL OF THE

FOAM PIECES AROUND

THE LEGS.

• DO NOT E AN EXTENSION CORD OR ANUS

ADAPTER PLUG WITH THIS A LIANCE.PP

Dryer must be electrically grounded in accordance with

local codes and ordinances, or in the absence of local

codes, in accordance with the NAT NAL ELECTRI-IO

CAL C E, ANSI/NFPA NO. 70. OD

WAR NG - TO DUCE THE RISK OFNI RE

FIRE, ELECTRICAL SHOCK AND PERSONAL

I URY:NJ

ELECTRICAL REQUIREMENTS

This dryer must be connected to an individual branch circuit,

protected by the required time-delay fuses or circuit breakers. A

four or three-wire, single phase, 120/240V or 120/208V, 60Hz,

30 amp circuit is required.

If the electric supply does not meet the above speciﬁcations, then

call a licensed electrician.

GROUNDING INSTRUCTIONS

This dryer must be connected to a grounded metal, permanent

wiring system, or an equipment-grounding conductor must be run

with the circuit conductors and connected to the equipment-

grounding terminal on the appliance.

RELOCATE GREEN

GROUND SCREW

HERE

STRAIN

RELIEF

BRACKET

GREEN OR

YELLOW WIRE

3/4", UL

RECOGNIZED

STRAIN RELIEF

HOT

WIRE

SCREWS

(3)

HOT

WIRE

COVER

NEUTRAL

(White)

REMOVE GROUND STRAP

AND DISCARD. KEEP GREEN

GROUND SCREW

4 #10 AWG MINIMUM COPPER

CONDUCTORS OR 120/240V 30A POWER

SUPPLY CORD KIT MARKED FOR USE

WITH DRYERS & PROVIDED WITH

CLOSED LOOP OR SPADE TERMINALS

WITH UPTURNED ENDS (NOT SUPPLIED).

INTERNAL DUCT

OPENING CHECK THAT EXHAUST

HOOD DAMPER OPENS

AND CLOSES FREELY.

WALL

WARNING:Only a 4-conductor cord shall be used when the

appliance is installed in a location where grounding through the

neutral conductor is prohibited. Grounding through the neutral is

prohibited for the new branch-circuit installations, mobile homes,

recreational vehicles, and areas where local codes prohibit

grounding through the neutral conduction.

CONNECTING DRYER USING 4-WIRE

CONNECTION (MUST BE USED FOR

MOBILE HOME INSTALLATION)

NOTES: SInce January 1,1996, the National Electric code requires

that the new constructions utilize a 4-wire connection to

an electric dryer

Remove and discard existing plastic or metal foil

transition duct and replace with UL listed transition

duct.

•

Produkt Specifikationer

Mærke:	Hotpoint
Kategori:	Tørretumbler
Model:	NWXR483EGWW

Har du brug for hjælp?

Hvis du har brug for hjælp til Hotpoint NWXR483EGWW stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Tørretumbler Hotpoint Manualer

Hotpoint NTM1192UK Manual

1 Februar 2025

Hotpoint NTM1182UK Manual

30 Januar 2025

Hotpoint NTM1192SSKUK Manual

30 Januar 2025

Hotpoint NWXR483GGWW Manual

14 Januar 2025

Hotpoint NT M11 9X3E IT Manual

29 December 2024

Hotpoint NT M11 82XB IT Manual

13 December 2024

Hotpoint NT M11 8X3K IT Manual

13 December 2024

Hotpoint NT M11 9X3SKY IT Manual

13 December 2024

Hotpoint NT M11 82K IT Manual

13 December 2024

Hotpoint NTS M11 9X3E IT Manual

13 December 2024

Tørretumbler Manualer

Nyeste Tørretumbler Manualer

BEKO DC9W Manual

19 Juni 2025

Infiniton SD-BC8EWN Manual

19 Juni 2025

Infiniton SD-BC8EDX Manual

19 Juni 2025

Electrolux EW6D4183P1 Manual

19 Juni 2025

Haier HD90-C367GU1 Manual

18 Juni 2025

Sogo SS-3665-P Manual

18 Juni 2025

Blomberg LTA18320 Manual

18 Juni 2025

Haier HD90-CQ387U1 Manual

18 Juni 2025

Haier HD100-C367GU1 Manual

18 Juni 2025

Haier HD100-CQ387U1 Manual

18 Juni 2025