Hotpoint NWXR483GGWW Manual

Hotpoint Tørretumbler NWXR483GGWW

Læs gratis den danske manual til Hotpoint NWXR483GGWW (8 sider) i kategorien Tørretumbler. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Hotpoint NWXR483GGWW, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Installation

Instructions

Gas Dryer

If you have any questions, call 1-800-GECARES (US) or 1-800-361-3400 (Canada)

or Visit our Web site at:

ww GEAppliances.comw.

MATERIALS YOU WILL NEED

LEVEL

Step 1 Verify Your Gas Installation (see section 2).

Step 2 Prepare the Area and Exhaust for Installation of

New Dryer (see section 1).

Step 3 Check and Insure the Existing External Exhaust is

Clean (see section 1) and Meets Attached Installation

Specifications (see section 6).

Step 4 Remove the Foam Shipping Pads (see section 1).

Step 5 Move the Dryer to the Desired Location.

Step 6 Level Your Dryer (see section 8).

Step 7 Connect the Gas Supply (see section 3) and check

for leaks (see section 4).

Step 8 Connect the External Exhaust (see section 7).

Step 9 Connect the Power Supply (see section 5).

Step 10 Check the Operation of the Power Supply, Gas

Connections, and Venting.

Step 11 Place the Owners Manual and the Installation

Instructions in a Location Where They Will Be

Noticed By the Owner.

For Alcove or Closet Installation see section 9.

For Bathroom or Bedroom Installation see section 10.

For Mobile or Manufactured Home see section .11

8" PIPE WRENCH

In the state of Massachusetts, installation must be performed by a qualified

or licensed contractor, plumber, or gasfitter qualified or licensed by the state.

WARNING RISK OF FIRE

• To reduce the risk of severe injury or death, follow all installation instructions.

• Clothes dryer installation must be performed by a qualified installer.

• Install the clothes dryer according to these instructions and in accordance with

local codes. In the absence of local codes, installation must comply with National

Fuel Gas Code, ANSIZ223.1/NFPA 54 or the Canadian Natural Gas and Propane

Installation Code, CSA B149.1.

• This dryer must be exhausted to the outdoors.

This act requires the governor of California to publish a list of substances known to the

state to cause cancer, birth defects or other reproductive harm and requires businesses to

warn customers of potential exposure to such substances. Gas appliances can cause minor

exposure to four of these substances, namely benzene, carbon monoxide, formaldehyde

and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.

Properly adjusted dryers will minimize incomplete combustion. Exposure to these

substances can be minimized further by properly venting the dryer to the outdoors.

•

California Safe Drinking Water and Toxic Enforcement Act

•

Use only 4” rigid metal ducting for exhausting the clothes dryer to the outdoors.

• Do not install or store this appliance in any location where it could be exposed to

water and or weather.

• Save these instructions. (Installers: Be sure to leave these instructions with the

customer).

• DO NOT install a clothes dryer with flexible plastic ducting materials. If flexible

metal (semi-rigid or foil-type) duct is installed, it must be UL-listed and installed

in accordance with the instructions found in "Connecting The Dryer To House

Vent" on page 6 of this manual. Flexible ducting materials are known to collapse,

be easily crushed, and trap lint. These conditions will obstruct dryer airflow and

increase the risk of fire.

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

•

IMPORTANT-

Save these

instructions for local inspector’s use.

•

IMPORTANT-

Observe

all governingcodes and ordinances.

• Note to Installer - Be sure to leave

these instructions with e omth cust er.

• Note to Customer - Keep these

instructions with your Use and Care

Book for future reference.

• Before the old dryer is removed from

service or discarded, remove the dryer

door.

•

Service information and the wiring dia-

gram are located in the control console.

• Do not allow children on or in the

appliance. Close supervision of child-

ren is necessary when the appliance is

used near children.

• Install the dryer where the temp-

erature is above 50°F for satisfactory

operation of the dryer control system.

• Inspect the dryer exhaust outlet and

straighten the outlet walls if they are

bent.

EXHAUST HOOD

FLEXIBLE GAS LINE CONNECTOR

SOAP SOLUTION

FOR LEAK DETECTION

PIPE

COMPOUND

DUCT TAPE

GLOVES

SAFETY GLASSES

4" DIAM METAL ELBOW

10" ADJUSTABLE WRENCHES

(x2)

4" DUCT CLAMPS

4" SPRING CLAMPS

(x2)

TOOLS YOU

WILL NEED

SLIP JOINT PLIERS FLAT BLADE SCREWDRIVER

4" DIA. FLEXIBLE METAL (SEMI-RIGID)

UL LISTED TRANSITION DUCT

(IF NEEDED)

KIT WX08X10077 (INCLUDES 2 ELBOWS)

4" DIA. METAL DUCT

(RECOMMENDED)

4" DIA. FLEXIBLE METAL (FOIL TYPE)

UL LISTED TRANSITION DUCT

(IF NEEDED.)

Installation Instructions

1 PREPARING FOR INSTALLATION

OF NEW DRYER

Minimum Clearance Other Than Alcove or Closet Installation

Minimum clearance to combustible surfaces and for air opening are: 0 in. clearance both sides and 1 in. rear. Consideration

must be given to provide adequate clearance for proper operation and service.

2 GAS REQUIREMENTS

DISCONNECTING GAS

The use of old flexible connectors can cause leaks and

personal injury. Always use new flexible connectors when

installing gas appliances.

WAR NG - NEVER R SE OLDNI EU

FLEXIBLE NNECTORS.CO

TILT THE DRYER SIDEWAYS

AND REMOVE THE FOAM

SHIPPING PADS BY

PULLING AT THE SIDES

AND BREAKING THEM

AWAY FROM THE DRYER

LEGS. BE SURE TO

REMOVE ALL OF THE

FOAM PIECES AROUND

THE LEGS.

•

Installation must conform to local codes and ordinances,

or in their absence, the NATIONAL FUEL GAS CODE,

ANSI Z223.

•This gas dryer is equipped with a Valve & Burner Assem-

bly for use only with natural gas. Using conversion kit

WE2 5X0217, your local service organization can convert

this dryer for use with propane (LP) gas. ALL CONVER-

SIONS S T BE MADE BY PRO RLY TRA DMU PE INE

AND QUAL D RSO L AND IN ACCOR-IFIE PE NNE

DA E WITH LOCAL CODES AND ORDINANCENC

REQUIREMENTS.

•The dryer must be disconnected from the gas supply

piping system during any pressure testing of that system

at a test pressure in excess of 0.5 PSI (3.4 KPa).

•The dryer must be isolated from the gas supply piping

system by closing the equipment shut-off valve during

any pressure testing of the gas supply piping of test

pressure equal to or less than 0.5 PSI (3.4 KPa).

WARNING

DRYER GAS SUPPLY CONNECTION

2-5/8" 3/8" NPT MALE THREAD GAS SUPPLY

NOTE: Add to vertical dimension

the distance between cabinet

bottom to floor.

GAS SUPPLY

•A 1/8-in.National Pipe Taper thread plugged tapping,

accessible for test gauge connection, must be installed

immediately upstream of the gas supply connection to

the dryer. Contact your local gas utility should you have

questions on the installation of the plugged tapping.

Supply line is to be 1

•Yo muu st use hwit t ish dr rye a fl iex bl mee tal co rnnecto

/2-in. rigid pipe and equipped with

an accessible shut-off within 6 ft. of, and in the same

room with the dryer.

•

Use pipe thread sealer compound or Teflon tape

appropriate for natural or LP gas.

li tes d co tnnec or ANSI 1.2Z2 4 / .10 C 6SA . The length of

the connect shall not exceed 3 ft.

•

Connect flexible metal connector to dryer and gas supply.

Open shut-off valve.

TIP: Install your dryer before installing your washer.

This will allow better access when installing dryer exhaust.

REMOVING LINT FROM WALL

EXHAUST OPENING

INTERNAL DUCT

OPENING CHECK THAT EXHAUST

HOOD DAMPER OPENS

AND CLOSES FREELY.

WALL

Remove and discard existing plastic or metal foil

transition duct and replace with UL listed transition

duct.

•

DISCONNECT AND DISCARD OLD

FLEXIBLE GAS CONNECTOR AND

OLD TRANSITION DUCTING

MATERIAL. REPLACE WITH NEW

CSA(AGA) APPROVED FLEXIBLE

GAS LINE CONNECTOR AND UL

APPROVED TRANSITION DUCT.

TURN GAS

SHUT-OFF VALVE

TO THE OFF

POSITION.

Produkt Specifikationer

Mærke:	Hotpoint
Kategori:	Tørretumbler
Model:	NWXR483GGWW

Har du brug for hjælp?

Hvis du har brug for hjælp til Hotpoint NWXR483GGWW stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Tørretumbler Hotpoint Manualer

Hotpoint C HD 84M WBS UK Manual

29 September 2025

Hotpoint HPT 83D BS IT Manual

5 August 2025

Hotpoint HPT 103D BS IT Manual

5 August 2025

Hotpoint H8 D94SB IT Manual

2 August 2025

Hotpoint HPTS 74D BS IT Manual

2 August 2025

Hotpoint NT M11 91WK EU Manual

2 August 2025

Hotpoint NT M11 82SK Manual

1 August 2025

Hotpoint NT M11 8X3SK EU Manual

1 August 2025

Hotpoint NT M11 8X3SK IT Manual

1 August 2025

Hotpoint NT M11 92E IT Manual

1 August 2025

Tørretumbler Manualer

Nyeste Tørretumbler Manualer

Zanussi-Electrolux Z 400 CDE Manual

4 Oktober 2025

Asko T709HUW Manual

4 Oktober 2025

Zanussi-Electrolux ZD 210 RE Manual

3 Oktober 2025

Zanussi-Electrolux TDS302T Manual

3 Oktober 2025

Zanussi-Electrolux TDE4235W Manual

3 Oktober 2025

Zanussi-Electrolux ZD 150 RL Manual

3 Oktober 2025

Zanussi-Electrolux ZDC46130W Manual

3 Oktober 2025

Zanussi-Electrolux ZDE26100W Manual

3 Oktober 2025

Zanussi-Electrolux ZD 110 R Manual

3 Oktober 2025

Zanussi-Electrolux TDE4234W Manual

3 Oktober 2025