JANDY PSB115 Manual

JANDY Ikke kategoriseret PSB115

Læs gratis den danske manual til JANDY PSB115 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om JANDY PSB115, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Installation Instructions
Pool and Spa
Air Blower
Models:
PSB110
PSB210
PSB115
PSB215
PSB120
PSB220
H0507900_REVJ
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
WARNING
: FOR YOUR SAFETY - This product must be installed and serviced by a contractor
who is licensed and qualifi ed in pool equipment by the jurisdiction in which the product will be installed where
such state or local requirements exist, the maintainer must be a professional with suffi cient experience in
pool equipment installation and maintenance so that all of the instructions in this manual can be followed
exactly. Before installing this product, read and follow all warning notices and instructions that accompany
this product. Failure to follow warning notices and instructions may result in property damage, personal
injury, or death. Improper installation and/or operation will void the warranty. Improper installation and/or
operation can create unwanted electrical hazard which can cause serious injury, property damage, or death.
Turn off all circuit breakers required in order to prevent the possibility of electric shock. If you have any
questions or need further details please contact Zodiac Pool Systems Customer Support at:
1.800.822.7933
WARNING
: RISK OF ELECTRIC SHOCK - Install at least 5 feet (1.5 m) from tub water
using nonmetallic plumbing. Install blower no less than 1 foot (305 mm) above the maximum water level
or with an approved Hartford loop confi guration as outlined in section 2 “Plumbing” to prevent water from
contacting electrical equipment. Install in accordance with the installation instructions.
To minimize the risk of severe injury or death the
appliance should not be subjected to the piping
system pressurization test. Local codes may
require the pool piping system to be subjected to a
pressure test. These requirements are generally not
intended to apply to the pool equipment. Zodiac
®
pool equipment is pressure tested at the factory.
However, if the WARNING cannot be followed and
pressure testing of the piping system must include
the appliance, BE SURE TO COMPLY WITH THE
FOLLOWING SAFETY INSTRUCTIONS:
- Check all clamps, bolts, lids, lock rings and
system accessories to ensure they are properly
installed and secured before testing.
- in the system before testingRELEASE ALL AIR
- Test water pressure must NOT EXCEED 35 PSI.
- Water temperature for test must NOT EXCEED
100°F (38°C).
Limit test to 24 hours. After test, visually check
system to be sure it is ready for operation.
NOTICE: these parameters apply to Zodiac
equipment only. For non-Zodiac equipment, consult
equipment manufacturer.
Installation must be done in accordance with the
National Electrical Code
®
(“NEC
®
” or NFPA-70
®
)
in the US, the Canadian Electrical Code (“CEC” or
C22.1) in Canada, and/or any other local and national
installation codes.
RISK OF ELECTRIC SHOCK, FIRE, PERSONAL
INJURY, OR DEATH. When required by applicable
local codes and/or by the Authority having jurisdiction
(AHJ); Connect only to a branch circuit that is
protected by a ground-fault circuit interrupter (GFCI).
Contact a qualified electrician if you cannot verify that
the circuit is protected by a GFCI. Make sure such a
GFCI is provided by the installer and should be tested
on a routine basis. To test the GFCI, push the test
button. The GFCI should interrupt power. Push the
reset button. Power should be restored. If the GFCI
fails to operate in this manner, the GFCI is defective.
If the GFCI interrupts power to the blower without the
test button being pushed, a ground current is flowing,
indicating the possibility of electrical shock. Do
not use the device. Disconnect the device and
have the problem corrected by a qualified service
representative before using.
-
To reduce the risk of injury, do not permit
children to use this product.
- Jandy Blowers are powered by high-voltage
electric motors and must be installed by a licensed
or - certifi ed electrician or a qualifi ed swimming pool
service technician.
- Incorrectly installed equipment may fail, causing
severe injury or property damage.
- Do not install on a plumbing line that can be
closed or shut off. The blower may create severe
enough pressures to cause property damage or
injury.
To Reduce the Risk of Injury -
a) The water in a spa should never exceed 104°F
(40°C). Water temperatures between 100°F (38°C)
and 104°F (40°C) are considered safe for a healthy
adult. Lower water temperatures are recommended
for young children and when spa use exceeds 10
minutes.
b) Since excessive water temperatures have a high
potential for causing fetal damage during the early
months of pregnancy, pregnant or possibly preg-
nant women should limit spa water temperatures to
100°F (38°C).
c) Before entering a spa or hot tub, the user should
measure the water temperature with an accurate
thermometer since the tolerance of water tempera-
ture-regulating devices varies.
d) The use of alcohol, drugs, or medication before
or during spa or hot tub use may lead to uncon-
sciousness with the possibility of drowning and can
greatly increase the risk of fatal hyperthermia.
e) Obese persons and persons with a history of
heart disease, low or high blood pressure, circula-
tory system problems, or diabetes should consult a
physician before using a spa.
f) Persons using medication should consult a
physician before using a spa or hot tub since some
medication may induce drowsiness while other
medication may affect heart rate, blood pressure,
and circulation.
g) People with infectious diseases should not use a
spa or hot tub.
h) Exercise care when entering or exiting the spa
or hot tub.
i) Water temperature in excess of 100°F (38°C)
may be injurious to your health.
j) Do not use a spa or hot tub immediately following
strenuous exercise.
k) Prolonged immersion in a spa or hot tub may be
injurious to your health.
l) Do not permit any electric appli-
ance (such as a light, telephone,
radio, or television) within fi ve 5 feet
(1.5m) of a spa or hot tub.
Attention installer: This manual contains important
information about the installation, operation and safe use
of this product. This information should be given to the
owner/operator of this equipment.
SAVE THESE INSTRUCTIONS
4. INSTALL BLOWER
Installation must be done in accordance with the National Electrical Code® (“NEC®”
or NFPA-70®) in the US, the Canadian Electrical Code (“CEC” or CSA C22.1) in
Canada, and/or any other local and national installation codes.
1. Refer to the “Select Blower” section (facing page) to ensure that you
have the correct blower size for your application.
2. Pressure tests to the system should be done prior to the installation
of the blower. See Warning Section on adjacent page.
3. Use 2" PVC pipe from the blower to jets or bubblers.
4. Slide Blower onto PVC Pipe. Lower until the stop
tabs make contact with the PVC pipe.
5. Blower should be installed vertically, away from
direct sunlight.
6. Do not glue or otherwise permanently attach the
blower to plumbing.
7. Do not remove the blower check valve diaphragm.
8. Drill two (2) 1/8 pilot holes through the textured fastener safe area "
marked on the blower body. The holes should be drilled through the blower
body and PVC pipe. The holes should be oriented 180°
from one another.
9. Install one (1) 1/2” 8-18 thread forming screw into
each of the previously drilled pilot holes. The screws and
pipe should not interfere with the normal travel of the
check valve diaphragm.
10. The blower also comes equipped with a mounting
bracket which can be used to secure the blower to a
Flat
Diaphragm
Travel
Distance
Flexed
Diaphragm
1/8" Bit
for Pilot Holes
Blower Body
PVC
Fastener
Safe Area
Fastener
Safe Area
Fastener
Safe Area
Stop Tabs
180°
2" PVC
Blower
Moutning Bracket
WARNING
Do not use chemical adhesives to
affi x the blower to the air inlet line.
Fumes from chemical adhesives
may accumulate in the piping and
explode causing property damage,
serious injury or death.
CAUTION
Blower must be affi xed to the plumbing using the fasteners
recommended in these instructions. Failure to do so may
allow the blower to come free of the plumbing during oper-
ation which could damage equipment and prevent proper
blower operation.
WARNING
Blower must be installed in an area well away from sourc-
es of exhaust such as gas pool and spa heater. Please
ensure that this blower is installed according to local codes
and Authority Having Jurisdiction (AHJ) requirements.
Correctly sizing the blower for your application is a critical step to the sustained operational quality
of your Jandy Pro Series Pool and Spa Blower. Damage or failure due to an improperly sized
blower is not covered under warranty.
SIZING WORKSHEETS: The worksheets below will guide you through the proper sizing
calculations for your application.
1. SELECT BLOWER
2. PLUMBING 3. WIRING
Vertical Measure from Pool/Spa surface to air outlet
Number of feet of 2” Pipe
Number of 90° Elbows
Number of 45° Elbows
Number of 1/2 lb check valves
Total Back Pressure
(Inches of Water)
Calculate Back Pressure
4
a
b
c
d
e
Vertical Measure from air outlet to lowest check valve (See Note)
a1
10
.5
.125
Calculate back
pressure as a measure
of “inches of water”.
Verifi cation of this
fi gure can be made by
using a manometer.
AIR HOLE
SIZE
CONVERSION
FACTOR
Calculate Airflow
1″
8
5″
32
3″
16
1″
4
3″
8
1.2 ″0.15
0.1
0.27
0.6
1.1
1.5
2.4
Jet
Total Airflow
SCFM
(Standard Cubic Feet Per Minute)
Conversion
Factor
No. of Holes
Air Flow Rate (SCFM)
Pressure H
2
O (Inches of Water)
0 10 20 30 40 50 60 70 80 90 100 120 130 140110
10
0
20
30
40
50
60
70
80
90
100
110
120
130
Performance Curves (60 HZ)
Models: PSB110
Models: PSB115
Models: PSB120
Max Back Pressure 40"
Max Back Pressure 50"
Max Back Pressure 65"
Models: PSB210
Models: PSB215
Models: PSB220
Voltage
Blower Selection
120V
1.5 HP 2.0 HP1.0 HP
PSB110 PSB115 PSB120
240V
PSB210 PSB215 PSB220
Determine Blower Needed
Choose an air hole size from
the chart at left and apply the
conversion factor in the formula
below to determine total airfl ow in
standard cubic feet per minute.
Installation of this equipment shoul
licensed electrician and conform to
(NEC®), state and local codes.
1. Ensure all power to the blower
disconnected at the main breaker.
2. Remove blower front door by re
the two (2) screws sliding the door
downward and pulling the door free
3. Pull in voltage source and grou
wire from Power Center.
4. Connect wires from power cent
the corresponding wires from the b
motor. Use the wiring diagrams bel
reference. The 120 or 240 toggle s
will come preinstalled with fl ag term
Connections will need to be made
Wire nuts.
WARNING
Installing an insuffi ciently
sized blower will
increase back pressure.
Failure to accurately
follow the blower
sizing calculations
provided could result
in excessive back
pressure. Excessive
pressure can cause
damage that could result
in electrocution causing
severe injury or death.
Water Line
Water Line
Air Line
Check Valve*
Spa Return
To Pump
Sump
to water level
12” min.
5’ - 25’
min. max.
Bubbler Jet
Venturi Jet
†
Blower
(installation with
Venturi Jets
†
)
Blower
(installation with
Bubbler Jets)
* Install a 1/2 lb. U.L. listed check valve between the
blower and the jets to prevent water damage to the blower.
Ensure that check valves are accessible for servicing.
†
Do not install adjustable jets. These may cause
excessive back pressure.
ON
OFF
Line 1
Neutral Bus Bar
Ground Bus Bar
From Blower Motor
From Power Center
Power Center
120V Toggle Switch
Flex Conduit
120V Wiring
RISK OF ELECTRIC SHOCK WHICH CAN RESULT IN SERIOUS
INJURY OR DEATH. Before attempting installation, ensure that all
power to the device is disconnected/turned off at the circuit breaker.
Be careful not to damage or abrade any wiring or other components.
LEGEND
Line 1
Neutral
Ground
ON
OFF
Line 2
ON
OFF
Line 1
Ground Bus Bar
From Power Center
Power Center
Flex Conduit
From Blower Motor
240V Toggle Switch
LEGEND
Line 1
Line 2
Ground
240V Wiring
RISK OF ELECTRIC SHOCK WHICH CAN RESULT IN SERIOUS
INJURY OR DEATH. Before attempting installation, ensure that all
power to the device is disconnected/turned off at the circuit breaker.
Be careful not to damage or abrade any wiring or other components.
Water Line
Water Line
Air Line
Air Line
Check Valve*
Sump
Spa Return
To Pump
to water level
12” min.
Over 25 Feet
Hartford loop
Plumb as
close to the
pool/spa wall
as possible.
Bubbler Jet
Venturi Jet
†
* Install a 1/2 lb. U.L. listed check valve between the blower
and the jets to prevent water damage to the blower.
Ensure that check valves are accessible for servicing.
†
Do not install adjustable jets. These may cause excessive
back pressure.
Blower
(installation with
Venturi Jets
†
)
Blower
(installation with
Bubbler Jets)
LONG RUN INSTALLATION
(over 25’ from spa wall)
STANDARD INSTALLATION
Screw
Conduit
Wires
Blower Door
Blower
From
Power Center
2” min.
water
level
Check
Valve*
Sump
Bubbler Jet
Blower
Water Line
Air Line
Spa
Return
To
Pump
Water Jet
* Install a 1/2 lb. U.L. listed check valve between the
blower and the jets to prevent water damage to the blower.
Ensure that check valves are accessible for servicing.
Hartford Loop -
To install the
blower below
water level, or if
the blower air
line drops
below the
bottom of the
spa, use the
Hartford Loop
plumbing
configuration to
prevent the air
line from filling
with water.
BELOW GRADE INSTALLATION
a
a
1
Spa
Deck Grade
Blower
e
dbc
NOTE: Include a1 for
installations with a check
valve below the air outlet
only. See “Below Grade
Installation” on facing page
for details. For above grade
installations enter 0 for a1.
Locate the total back pressure, calculated above
and draw a horizontal line. Locate the total airfl ow
from previous step and draw a vertical line. These
lines will intersect on the performance curve of the
minimum HP blower required for your application.

Produkt Specifikationer

Mærke: JANDY
Kategori: Ikke kategoriseret
Model: PSB115

Har du brug for hjælp?

Hvis du har brug for hjælp til JANDY PSB115 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret JANDY Manualer

JANDY

JANDY SpaLink RS Manual

3 December 2024
JANDY

JANDY Erosion Feeder Manual

2 September 2024
JANDY

JANDY TruChlor Erosion Feeder Manual

2 September 2024
JANDY

JANDY PSB110 Manual

1 September 2024
JANDY

JANDY JS100-SM Manual

1 September 2024
JANDY

JANDY SFTM24-2.0 Manual

1 September 2024
JANDY

JANDY JS60-SM Manual

1 September 2024
JANDY

JANDY SFSM-60 Manual

1 September 2024
JANDY

JANDY QT Residential Blower Manual

31 August 2024
JANDY

JANDY AquaSwitch Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Planet Audio

Planet Audio P100CPA Manual

15 Juni 2025
Sabrent

Sabrent BK-MAC2 Manual

15 Juni 2025
Planet Audio

Planet Audio P9950CPA Manual

15 Juni 2025
Filmcity

Filmcity FC-CTH-01 Manual

15 Juni 2025
Cleveland

Cleveland 22CGT6 Manual

15 Juni 2025
Auray

Auray SVRK-4U-S Manual

15 Juni 2025
Bobrick

Bobrick B-2860 Manual

15 Juni 2025
Sony

Sony ODBK-103 Manual

15 Juni 2025
Planet Audio

Planet Audio P70CPA Manual

15 Juni 2025
Gourmia

Gourmia GAF657 Manual

15 Juni 2025