Juki S159-162 Manual

Juki Symaskine S159-162

Læs gratis den danske manual til Juki S159-162 (4 sider) i kategorien Symaskine. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Juki S159-162, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

– 1 –

INSTRUCTION MANUAL

Swing-type gathering device

S159・S160

S161・S162

No.03

29114915

1. Name

Swing-type gathering device for the MO-3000, MO-6000 series of overlock/safety stitch machine

S159 : Swing-type gathering device for safety stitch machines (pedal-operated)

S160 : Swing-type gathering device for safety stitch machines (lever-operated)

S161 : Swing-type gathering device for overlock machines (pedal-operated)

S162 : Swing-type gathering device for overlock machines (lever-operated)

2. Applicable models

MO-3 △04E-0E6 MO-3 △04E-0F6 MO-6 △14-BE6

MO-3 △12E-DF6 MO-3 △14E-BE6 MO-6 △16-DE4

MO-3 △14E-BD6 MO-3 △16E-DE4 MO-6 △16-FF6

MO-3 △14E-BF6 MO-3 △16E-FF6

MO-3 △16E-DD4 MO-3 △43E-FBD6

MO-3 △16E-DF6 MO-3 △16E-RH6

3. Specications

Parts to be replaced when the gathering device is used with the overlock/safety stitch machine

To operate an overlock/safety stitch machine in combination with the S159, S160, S161 or S162 gathering device, the gauge

components need to be changed accordingly. Choose the appropriate parts from among those listed in the table below.

(1) Safety stitch machines (MO-3 △16E, 3 △43E, 6 △16) S159 or 161

Read safety instructions carefully and understand them before using.

Retain this Instruction Manual for future reference.

CAUTION :

This Instruction Manual is intended for the S159/S160/S161/S162. Read and fully understand the

instructions given under “IMPORTANT SAFETY INSTRUCTIONS” in the Instruction Manual the MO-

3000, MO-6000 series before putting the machine into service when this device is installed to the

MO-3000, MO-6000 series.

In addition, to emphasize the S159/S160/S161/S162, some illustrations of the MO-3000, MO-6000

seriesaresimplied.Also,illustrationsofthesafetydevicesarepartiallyomitted.

＊ Use the gathering foot onry when the RH6 gauge set is used.

Application For continuous gathering and partial shirring on light-weight materials including

knnitted fabric, light-weight knits and broadcloth.

Sewing speed Up to 7000 rpm

Differential feed ratio Overlock machines 1 : 3 Safety stitch machines 1 : 3

(Adjust appropriately in accordance with the type of material to be used.)

Lift of the presser foot Overlock machine : 6 mm Safety stitch machine : 6 mm

(5 mm only for RH6)

Gauge size

DD4 DE4 DF6 FF6 RH6 FBD6

Name

Presser joint 12154654 12154654 12154753 12154852 12154951 11975950

Main feed dog 12170700 12170700 12170809 12170908 12170908 11884806

Differential feed dog 12172904 12172904 12173407 12173407 12173407 11885902

Throat plate R4508J0DD0B R4508J6ED0B R4608J0FD0A R4612J6FD0A R4617J0HD0A R4612J0DE02

＊Gathering foot ーーーー

＊MAS0510800A

ー

– 2 –

WARNING :

So as to prevent accidents caused by abrupt start of the machine, start the job after turning OFF

thepowertothemachineandconrmingthatthesewingmachinewillnotrunevenbydepressing

the start pedal.

(2) Overlock machines (MO-3 △04E, 3 △14E, 6 △14) S160 or 162

5. Adjusting the gathering foot

Gathering foot

Section C Screw

Bracket A

(1) Adjust the gathering foot so that it comes in

parallel contact with the top surface of the

throat plate over the length.

a. Temporarily tighten screw A, loosen screw B, and

adjust the parallelism between the gathering foot and

the throat plate.

b. After the completion of sewing, tighten screw

B and

screw A.

(2) Adjusting the vertical position and the lateral

position of the gathering foot

a. Loosen two screws D and screw E in the thrust collar,

and adjust the position of the gathering foot, in the

lateral direction, so that it is 3 mm spaced from the

edge of the feed dog.

Gathering foot

Adjust the gathering foot by

pressing down section C.

Adjust the gathering foot by

pressing up section C.

Good

Not good

The gathering foot comes

in parallel contact with the

throat plate.

Gathering foot

(2-row feed dog)(3-row feed dog)

3 mm 3 mm

Throat plate

Gauge size

0E6 0F6 BD6 BE6 BF6 DF6

Name

Presser joint 11878857 11974250 11879350 11879350 12153052 11974052

Main feed dog 11883402 11883402 11883402 11883402 11883402 11884608

Differential feed dog 12171807 12171807 12171807 12171807 12171807 12171906

Throat plate R4300J0EE0B R4300J0FE0A R4305J0DE0A R4305J6EE0A R4617J0HD0A R4308J0FE00

Produkt Specifikationer

Mærke:	Juki
Kategori:	Symaskine
Model:	S159-162

Har du brug for hjælp?

Hvis du har brug for hjælp til Juki S159-162 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Symaskine Juki Manualer

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

Juki MS-1261A-DWS Manual

9 August 2025

Symaskine Manualer

Nyeste Symaskine Manualer

Husqvarna-Viking Designer Topaz 50 Manual

7 August 2025

Husqvarna-Viking H-Class 600E Manual

7 August 2025

Husqvarna-Viking Designer Topaz 40 Manual

7 August 2025

Husqvarna-Viking Designer Epic 3 Manual

7 August 2025

Husqvarna-Viking Sapphire 875 Quilt Manual

7 August 2025

Husqvarna-Viking Sapphire 835 Manual

7 August 2025

Husqvarna-Viking Designer Jade 35 Manual

7 August 2025

Husqvarna-Viking Huskylock s21 Manual

6 August 2025

Husqvarna-Viking Designer Ruby deLuxe Manual

6 August 2025

Husqvarna-Viking Designer Diamond deLuxe Manual

6 August 2025