Juki SC-923 Manual

Juki Symaskine SC-923

Læs gratis den danske manual til Juki SC-923 (59 sider) i kategorien Symaskine. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Juki SC-923, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/59
1
INSTRUCTION MANUAL
SC-923
– 1 –
I. SPECIFICATIONS
Supply voltage Single phase 100 to 120V 3-phase 200 to 240V Single phase 220 to 240V
Frequency 50Hz/60Hz 50Hz/60Hz 50Hz/60Hz
Operating environment Temperature : 5 to 35˚C
Humidity : 35 to 85%
Temperature : 5 to 35˚C
Humidity : 35 to 85%
Temperature : 5 to 35˚C
Humidity : 35 to 85%
Input 600VA 600VA 600VA
* The electric power is a reference value for the model equipped with the LU-2810ES-7 machine head.
It differs by the selected machine head.
II. SET-UP
The SC-923 can be used with the direct-motor type machine head as a stand-alone control box.
This describes the procedure for installing the SC-
923 on the table of the LU-2810ES-7 sewing ma-
chine. To use any other machine head, install the
control box on the table referring to the Instruction
Manual for the main body of the relevant sewing ma-
chine. Install the control box suspending plate on the
table with mounting bolts supplied with the unit. At
this time, insert the nuts and washers supplied with
the unit as accessories as shown in the gure so that
the motor unit can be securely xed on the table.
1) Press three bolts ❶ supplied with the unit as ac-
cessories into the motor hanging bolt hole in the
table and x them.
2) Fix suspending plate ❺ supplied with the unit on
the three bolts with plain washer ❷, spring wash-
er ❸ and nut ❹.
3) Fix rubber ❻ on the suspending plate with spring
washer ❼ and nut ❽.
4) Hang one end of the control box on the threaded
part of rubber on the side which has two bolts.
Then, hang the other end of the control box on
the opposite side.
5) Temporarily x the other threaded part of rubber
with plain washer ❾ and nut 󱢳. In this case, the
spring washer is not used.
6) Adjusting the installing position of the control box.
Then, securely tighten the nuts.
1. Installing to the table
To use the SC-923 with the direct-motor type machine head, install the control box on the table according to
the following instruction.
❶
❶
❹
❷
❸
❺
❼
❽
❻
❾
󱢳

Produkt Specifikationer

Mærke: Juki
Kategori: Symaskine
Model: SC-923

Har du brug for hjælp?

Hvis du har brug for hjælp til Juki SC-923 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Symaskine Juki Manualer

Juki

Juki LK-1903BN Manual

30 December 2025
Juki

Juki MH-380 Manual

30 December 2025
Juki

Juki MH-382 Manual

30 December 2025
Juki

Juki S161 Manual

27 September 2024
Juki

Juki LU2-4410-B1T-CS Manual

1 September 2024
Juki

Juki LU-2210 Manual

29 August 2024
Juki

Juki AW-3SD Manual

29 August 2024
Juki

Juki DNU-1541-7 Manual

29 August 2024
Juki

Juki TU-273 Manual

29 August 2024
Juki

Juki PLK-J12060R Manual

28 August 2024

Symaskine Manualer

Nyeste Symaskine Manualer

Alfa

Alfa Unique Heavy Duty Manual

17 Juni 2025
Janome

Janome Horizon Memory Craft 7700QCP Manual

10 Juni 2025
Singer

Singer HD 6705C Manual

31 Maj 2025
Janome

Janome Sweet Pea Manual

4 Marts 2025
Janome

Janome Lovely 001 Manual

4 Marts 2025
Janome

Janome Sew Fresh Manual

4 Marts 2025
Janome

Janome Watermelon Crush Manual

4 Marts 2025
Janome

Janome Mystical Mint Manual

4 Marts 2025
Janome

Janome MyLock 454D Manual

4 Marts 2025
Janome

Janome Horizon Memory Craft 9400 Manual

12 Februar 2025