Juki UT55 Manual

Juki Symaskine UT55

Læs gratis den danske manual til Juki UT55 (22 sider) i kategorien Symaskine. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Juki UT55, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/22

INSTRUCTION MANUAL

MF-7900(D)/UT55,56,57

CONTENTS

I. SPECIFICATIONS ...........................................................................................................1

II. AT THE BEGINNING......................................................................................................1

III. INSTALLING THE ACCESSORIES.............................................................................2

1. Installing the presser lifting cylinder 2 ............................................................................................

2. Installing the air regulator 2 ..............................................................................................................

3. Installation and setting SC-921 3 ......................................................................................................

(1) Installing the SC-921 on the table ( Table-mount type ) 3 ............................................................................

(2) Installing the SC-921 on the table ( Semi-submerged type ) 3 ....................................................................

(3) Connecting the cords 4 ...................................................................................................................................

(4) Setting procedure of the machine head 5 .....................................................................................................

(5) Setting the lower stop position of the needle bar 6 .....................................................................................

IV. AIR PIPING DRAWING.................................................................................................7

1. Piping of the thread trimmer device (UT57) 7 ..................................................................................

2. Piping of the thread trimmer device (UT55) 8 ..................................................................................

3. Piping drawing for air blow (UT56) 9 ................................................................................................

4. Adjusting the air regulator 9 .............................................................................................................

V. THREADING THE MACHINE HEAD ..........................................................................10

VI. ADJUSTING THE LOOPER THREAD TRIMMER MECHANISM ...........................11

1. Adjusting the thread trimmer air cylinder ....................................................................................11

2. Adjusting the Lower knife 12 ............................................................................................................

3. Adjusting the position of clamp pressure adjusting spring 12 .....................................................

4. Adjusting the knife engagement and the knife pressure adjusting spring 12 .............................

5. Adjusting the pressure of clamp spring 12 .....................................................................................

6. Initial position of the looper thread trimmer mechanism 13 ..........................................................

7. Adjusting the stopper 13 ...................................................................................................................

8. Adjusting the height of the lower knife 13 .......................................................................................

9. Adjusting the lower knife holder guide 13 .......................................................................................

10. Adjusting the longitudinal position of the blade point of lower knife 14 ......................................

11. Adjusting the thread trimmer sensor 14 ..........................................................................................

12. Adjusting the speed of looper thread trimmer 14 ...........................................................................

VII. ADJUSTING THE THREAD RELEASE MECHANISM ..........................................15

1. Adjusting the disk-rise 15 .................................................................................................................

2. Adjusting the thread release hook 15 ..............................................................................................

VIII. ADJUSTING THE TOP COVERING THREAD TRIMMER MECHANISM ............16

1. Adjusting the engagement of knives 16 ..........................................................................................

2. Adjusting the pressure of clamp spring 16 .....................................................................................

3. Adjusting the position of the blade point of moving knife 16 ........................................................

4. Adjusting the speed of moving knife 17 ..........................................................................................

IX. ADJUSTING THE AIR-BLOW WIPER (UT56) .........................................................18

1. Installing the air-blow wiper 18 .........................................................................................................

2. Adjusting the air-blow wiper 18 ........................................................................................................

X. ADJUSTING THE NEEDLE THREAD WIPER (UT55) ..............................................19

1. Adjusting the clamp spring 19 ..........................................................................................................

2. Installing the needle thread wiper 19 ...............................................................................................

XI. MAINTENANCE ..........................................................................................................20

1. Cleaning the motor fan 20 .................................................................................................................

Produkt Specifikationer

Mærke:	Juki
Kategori:	Symaskine
Model:	UT55

Har du brug for hjælp?

Hvis du har brug for hjælp til Juki UT55 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Symaskine Juki Manualer

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

Juki MS-1261A-DWS Manual

9 August 2025

Symaskine Manualer

Nyeste Symaskine Manualer

Husqvarna-Viking Designer Topaz 50 Manual

7 August 2025

Husqvarna-Viking H-Class 600E Manual

7 August 2025

Husqvarna-Viking Designer Topaz 40 Manual

7 August 2025

Husqvarna-Viking Designer Epic 3 Manual

7 August 2025

Husqvarna-Viking Sapphire 875 Quilt Manual

7 August 2025

Husqvarna-Viking Sapphire 835 Manual

7 August 2025

Husqvarna-Viking Designer Jade 35 Manual

7 August 2025

Husqvarna-Viking Huskylock s21 Manual

6 August 2025

Husqvarna-Viking Designer Ruby deLuxe Manual

6 August 2025

Husqvarna-Viking Designer Diamond deLuxe Manual

6 August 2025