Kenwood CA-CUT14 Manual

Kenwood Ikke kategoriseret CA-CUT14

Læs gratis den danske manual til Kenwood CA-CUT14 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Kenwood CA-CUT14, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Take the time to read through this instruction manual.

Familiarity with installation and operation procedures will help you obtain the best performance from your new product.

CA-CUT14

CUT-IN LID KIT FOR 6” X 9” SPEAKERS DESIGNED AND ENGINEERED

FOR 2014-UP HARLEY-DAVIDSON® RUSHMORE MOTORCYCLES WITH

FACTORY-STYLE HARD SADDLEBAGS

INSTRUCTION MANUAL

JVCKENWOOD Corporation

Figure 1.1

Safety precautions

WARNING

Contents

Section 1: Getting Started.......................................................2

Section 2: Disassembling The Factory Lid............................3

Section 3: Mounting The Templates......................................4

Section 4: Wiring The Saddlebags For Speakers.................7

Section 5: Wiring From Amplifier To Saddlebags...............7

The factory saddlebag hinges limit the size of the speaker magnet that can be

used and allow the lids to open and close without issue. KENWOOD assumes

ZERO RESPONSIBILITY for tment issues, or water leaks when any speaker

brand other than KENWOOD is used.

Do Not Use “Thread Lock” or “Screw Glue” of any kind, as it destroys plastic and

will cause part failure.

Most speaker magnets are large and powerful. Credit cards and electronics

can be sensitive to magnets, so please exercise caution in how you pack your

saddlebags. Metal objects packed into your bags may end up stuck to the

magnet, so please use caution when opening the lids. Magnets can also get

hot when speakers are being played, especially at higher volumes. Please

consider this when packing your saddlebags.

Section 1 - Getting Started

Installation procedure

1. Remove the saddlebag from the bike and put it on a stable working surface (placing

blankets, towels, etc. on your work surface will help to protect the paint).

2. The black circle in Fig 1.1 is where a 5/8”

(16mm) hole will need to be drilled. This

hole is where the supplied silicone grommet

will go to allow the lid’s speaker wire to pass

through from the saddlebag. Use masking

tape over the painted area to be drilled and

start with a small bit, gradually working your

way up to the 5/8” (16mm) hole. Drilling the

hole with the lid still on is recommended.

Produkt Specifikationer

Mærke:	Kenwood
Kategori:	Ikke kategoriseret
Model:	CA-CUT14

Har du brug for hjælp?

Hvis du har brug for hjælp til Kenwood CA-CUT14 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Kenwood Manualer

Kenwood KAC-334 Manual

21 Juni 2025

Kenwood NX-1800H Manual

20 Juni 2025

Kenwood CA-LPM10 Manual

20 Juni 2025

Kenwood NX-1700H Manual

20 Juni 2025

Kenwood KSC-PSW10ST Manual

20 Juni 2025

Kenwood KSC-50CR Manual

25 Marts 2025

Kenwood KRK-15B Manual

24 Marts 2025

Kenwood VGS-1 Manual

24 Marts 2025

Kenwood KSC-25LS Manual

24 Marts 2025

Kenwood KPG-46U Manual

24 Marts 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Ikea VÅGSTRANDA 505.118.76 Manual

4 Juli 2025

Ikea MAXIMERA 102.850.26 Manual

4 Juli 2025

Rowenta Ultima CF7242 Manual

4 Juli 2025

Lumens VC-TR61N Manual

4 Juli 2025

Belkin F8W973 Manual

4 Juli 2025

Ikea VÅGSTRANDA 105.118.83 Manual

4 Juli 2025

Schneider LUCAX6ES Manual

4 Juli 2025

Katadyn Steripen Ultra Manual

4 Juli 2025

SilverCrest SSVF 38 A2 Manual

4 Juli 2025

IFM AC1304 Manual

4 Juli 2025