Kenwood Excelon CA-HRN98UT Manual

Kenwood Ikke kategoriseret Excelon CA-HRN98UT

Læs gratis den danske manual til Kenwood Excelon CA-HRN98UT (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Kenwood Excelon CA-HRN98UT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Take the time to read through this instruction manual.

Familiarity with installation and operation procedures will help you obtain the best performance from your new product.

CA-HRN98UT

REAR SPEAKER HARNESS DESIGNED AND ENGINEERED

FOR 98-13 HARLEY-DAVIDSON® ULTRA MOTORCYCLES

INSTRUCTION MANUAL

JVCKENWOOD Corporation

Important Notes

are registered trademarks of JVCKENWOOD Corporation. Harley-Davidson®, Electra

Glide®, Road Glide®, Street Glide®, Ultra Classic®, Tri Glide®, CVO™, Screamin Eagle®

and Tour-Pak® are trademarks or registered trademarks of Harley-Davidson, Inc. and/

or its affiliates and if used or implied are for reference only. There is no affiliation

between Harley-Davidson, Inc. and/or its aliates and JVCKENWOOD Corporation

and/or its aliates. All other trademarks are the property of their respective owners.

Specications subject to change without notice.

Rear Speaker Harness Installation Instructions

Installation procedure

1. You will see that one end of this harness has two 4-pin connectors. One of these white

4-pin plugs will plug into the “amplied out” on the amp that will power the rear speakers.

The amplifier comes with a short harness with a black 8-pin plug and two 4-pin blue

plugs. Plug the 8-pin black plug into the amplier’s input that will power the rear speakers.

The second 4-pin plug marked “rear in” on the rear speaker harness will plug into one of

the blue 4-pin connectors, noting they will only go in one way.

2. The harness that will run the rear speakers will pass under the inner fairing on the clutch

side of the bike. Loosen the tank’s “chrome console” and run the wires up and over the gas

tank, but under the tank’s chrome console. There is a provision on the front of the console

for wires to pass under it allowing the power harness to run on the brake side of the ller

spout and the rear speaker harness to run on the clutch side of the spout.

NOTE: Although not necessary, the power and rear harnesses can go under the gas tank if

you choose to remove and re-install the tank. With the tank removed you will see a factory

wire channel where wires pass along the bike’s frame. Removing the top of the channel

will allow for the power and rear speaker harness to be safely run under the tank to the

battery area. When reinstalling the top of the channel take care not to pinch any wires

along the edges of the channel.

3. When installed on the bike, you will see that this harness has a white 8-pin plug towards

the back of the bike. This is a “quick disconnect” for bikes that have the large “tour pak”

removeable, and allows the rear speakers to be plugged in or unplugged easily. The end

of the harness that will be at the rear end of the bike is split into 2 groups of 4 wires, one

marked “clutch side”, and one marked “brake side”. If you are sitting on the bike looking

forward, the brake side is on your right-hand side. Remove the factory rear speakers from

each rear “pod”. Each group of wires will enter the rear pod where the factory wires enter

the pod. The factory speaker wires will plug into the male spades on each side, and the

female spades on this harness will plug directly onto each rear speaker.

NOTE: Factory rear wires DO NOT have insulators. Once the factory rear wires are plugged

into this harness, please wrap each connection with electrical tape to prevent the wires

from shorting against each other.

For updated information (the latest Instruction Manual, etc.),

please visit the following website:

https://manual.kenwood.com/en_contents/search/

Produkt Specifikationer

Mærke:	Kenwood
Kategori:	Ikke kategoriseret
Model:	Excelon CA-HRN98UT

Har du brug for hjælp?

Hvis du har brug for hjælp til Kenwood Excelon CA-HRN98UT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Kenwood Manualer

Kenwood Abbey Lux ZJP05 Manual

5 Oktober 2025

Kenwood Mesmerine TFM810 Manual

4 Oktober 2025

Kenwood Elegancy ZJP11 Manual

4 Oktober 2025

Kenwood Abbey Lux TCP05 Manual

3 Oktober 2025

Kenwood NXR-1700-E Manual

27 August 2025

Kenwood AT550 Manual

7 August 2025

Kenwood Chef Sense KVC5001Y Manual

14 Juli 2025

Kenwood KNB-L1 Manual

9 Juli 2025

Kenwood KNB-63L Manual

9 Juli 2025

Kenwood KNB-70LEX Manual

9 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

GBC W12 Manual

14 Oktober 2025

Fuxtec FX-CT100 Manual

13 Oktober 2025

Scotsman Prodigy Plus NH0422 Manual

13 Oktober 2025

Chief FCA800HS Manual

13 Oktober 2025

Chief OLCM1U Manual

13 Oktober 2025

IPEGA PG-P5V002 Manual

13 Oktober 2025

IPEGA PG-P5013 Manual

13 Oktober 2025

IPEGA PG-SW2210 Manual

13 Oktober 2025

IPEGA PG-P5042 Manual

13 Oktober 2025

Scotsman Prodigy Plus NH0922 Manual

13 Oktober 2025