Kenwood Excelon CA-PLT14SG Manual

Kenwood Ikke kategoriseret Excelon CA-PLT14SG

Læs gratis den danske manual til Kenwood Excelon CA-PLT14SG (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Kenwood Excelon CA-PLT14SG, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Take the time to read through this instruction manual.

Familiarity with installation and operation procedures will help you obtain the best performance from your new product.

CA-PLT14SG

AMPLIFIER MOUNTING PLATE DESIGNED AND ENGINEERED FOR

2014-UP HARLEY-DAVIDSON® STREET GLIDE®, ULTRA, OR ULTRA TRIKE

MOTORCYCLES

INSTRUCTION MANUAL

JVCKENWOOD Corporation

Important Notes

are registered trademarks of JVCKENWOOD Corporation. Harley-Davidson®, Electra

Glide®, Road Glide®, Street Glide®, Ultra Classic®, Tri Glide®, CVO™, Screamin Eagle®

and Tour-Pak® are trademarks or registered trademarks of Harley-Davidson, Inc. and/

or its affiliates and if used or implied are for reference only. There is no affiliation

between Harley-Davidson, Inc. and/or its aliates and JVCKENWOOD Corporation

and/or its aliates. All other trademarks are the property of their respective owners.

Specications subject to change without notice.

The CA-PLT14SG plate is made to mount ampliers

with a maximum dimension of 8.5” W x 7” D x 2” H

(216mm x 178mm x 51mm).

Installation procedure

1. Over the top of the radio, pull up to release each wire harness from the black plate

via the factory “Christmas tree” fasteners. If your bike has factory GPS, the small square

antenna will need to be relocated just behind the voltmeter as shown in Fig 1.1 below.

Figure 1.1 - The white circle shows the new location for the GPS Antenna if your bike

came factory equipped with this feature.

2. Remove the four factory T-20 “Torx” screws that go through the top of the black plate

and into the top of the radio. Set these screws aside for now.

3. Sit the main amplier plate over the top of the radio, noting the 4 holes in the plate will

line up with the 4 holes left by the factory screws just removed. The factory screws will

now go through the main mounting plate, through the black plate over the top of the

radio, and into the top of the radio.

4. Locate the Velcro® that came in the box and stick it to the bottom plate of the amp

being installed. You can now “stick” the amp to the mounting plate just installed.

Depending on the amp you are installing, you can use the “tabs” on the CA-PLT14SG to

re-secure the wire harnesses that were held in place using the “Christmas Tree Fasteners.”

For updated information (the latest Instruction Manual, etc.),

please visit the following website:

https://manual.kenwood.com/en_contents/search/

Produkt Specifikationer

Mærke:	Kenwood
Kategori:	Ikke kategoriseret
Model:	Excelon CA-PLT14SG

Har du brug for hjælp?

Hvis du har brug for hjælp til Kenwood Excelon CA-PLT14SG stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Kenwood Manualer

Kenwood KSC-50CR Manual

25 Marts 2025

Kenwood KRK-15B Manual

24 Marts 2025

Kenwood VGS-1 Manual

24 Marts 2025

Kenwood KSC-25LS Manual

24 Marts 2025

Kenwood KPG-46U Manual

24 Marts 2025

Kenwood KPG-43U Manual

24 Marts 2025

Kenwood CAX-AD100 Manual

18 Marts 2025

Kenwood kMix FPX935 Manual

22 Februar 2025

Kenwood kMix FPX937 Manual

22 Februar 2025

Kenwood kMix FPX934 Manual

22 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Simrad Active Imaging HD (Thru-Hull) Manual

14 Juni 2025

Garritan Harps Manual

14 Juni 2025

Marshall CV-H20-HF Manual

14 Juni 2025

Aiphone IXW-MAA Manual

14 Juni 2025

Rival HM-743 Manual

14 Juni 2025

Lutec Avony Manual

14 Juni 2025

Giordani G-SAFE & PLAY Manual

14 Juni 2025

Gourmia GAF799 Manual

14 Juni 2025

Arendo 307503 Manual

14 Juni 2025

Hughes & Kettner Tube 100 Manual

14 Juni 2025