Kenwood Excelon CA-PLT14SG3 Manual

Kenwood Ikke kategoriseret Excelon CA-PLT14SG3

Læs gratis den danske manual til Kenwood Excelon CA-PLT14SG3 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Kenwood Excelon CA-PLT14SG3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Take the time to read through this instruction manual.

Familiarity with installation and operation procedures will help you obtain the best performance from your new product.

CA-PLT14SG3

AMPLIFIER MOUNTING PLATE DESIGNED AND ENGINEERED FOR

2014-UP HARLEY-DAVIDSON® FLH MOTORCYCLES

INSTRUCTION MANUAL

JVCKENWOOD Corporation

FLH Side Plate Installation Instructions

Installation procedure

1. With your ignition switch in the "OFF" position, remove your outer fairing/headlamp

assembly and set it aside. Refer to a service manual if you need help with this.

NOTE: Placing a towel on the front fender can help prevent scratches or "dings" from

dropped tools or fasteners, etc.

2. Clutch Side Speaker Cabinet Removal: The images below show the 8 fasteners that

will need to be removed to allow the clutch side cabinet to be removed from the bike.

If your bike has the CB module, (mounted "sideways" on the clutch side cabinet), undo

the antenna cable and main harness. The CB module will stay attached to the clutch side

cabinet when removed. Undo the speaker wire plugs going into the cabinet (pink & pink

with black stripe wires). If your bike had the CB Module, remove its mounting plate from

the speaker cabinet.

3. Attaching the Main Plate to the Speaker Cabinet: On the side of the cabinet, you will

see a threaded insert and a locating post as seen in Fig 1.3. Put the main plate on the

cabinet so one of the holes in the plate goes over the locating post, and the other sits

over the threaded insert. If you removed a CB module from an Ultra, you can use the

screw that secured that module to the speaker pod. If your bike did not have a CB module,

use the machine screw that came in the kit to secure the side plate to the speaker cabinet.

Fig 1.3 on the next page shows the plate correctly placed on the speaker cabinet.

Figure 1.1 - Side View of Cabinet Figure 1.2 - Back View of Cabinet

Note: Brake Side Shown, But Fastener

Location is the Same for Clutch Side

Produkt Specifikationer

Mærke:	Kenwood
Kategori:	Ikke kategoriseret
Model:	Excelon CA-PLT14SG3

Har du brug for hjælp?

Hvis du har brug for hjælp til Kenwood Excelon CA-PLT14SG3 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Kenwood Manualer

Kenwood Abbey Lux ZJP05 Manual

5 Oktober 2025

Kenwood Mesmerine TFM810 Manual

4 Oktober 2025

Kenwood Elegancy ZJP11 Manual

4 Oktober 2025

Kenwood Abbey Lux TCP05 Manual

3 Oktober 2025

Kenwood NXR-1700-E Manual

27 August 2025

Kenwood AT550 Manual

7 August 2025

Kenwood Chef Sense KVC5001Y Manual

14 Juli 2025

Kenwood KNB-L1 Manual

9 Juli 2025

Kenwood KNB-63L Manual

9 Juli 2025

Kenwood KNB-70LEX Manual

9 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

GBC W12 Manual

14 Oktober 2025

Fuxtec FX-CT100 Manual

13 Oktober 2025

Scotsman Prodigy Plus NH0422 Manual

13 Oktober 2025

Chief FCA800HS Manual

13 Oktober 2025

Chief OLCM1U Manual

13 Oktober 2025

IPEGA PG-P5V002 Manual

13 Oktober 2025

IPEGA PG-P5013 Manual

13 Oktober 2025

IPEGA PG-SW2210 Manual

13 Oktober 2025

IPEGA PG-P5042 Manual

13 Oktober 2025

Scotsman Prodigy Plus NH0922 Manual

13 Oktober 2025