La Crosse Technology LTV-R2 Manual

La Crosse Technology Ikke kategoriseret LTV-R2

Læs gratis den danske manual til La Crosse Technology LTV-R2 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 96 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 48.5 anmeldelser. Har du et spørgsmål om La Crosse Technology LTV-R2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Model: LTV-R2

DC: 090517

Rain Sensor

Insert 2- AA batteries into the rain sensor according to polarity.

1. Flip open both locking tabs on your rain sensor and lift o the funnel portion.

2. Pull up on the battery cover and remove.

3. Install 2-AA batteries according to polarity. Reposition the battery cover over the battery compartment,

and ﬁrmly push down to lock it back into place

5. Remove cardboard and any tape around the rocker before use. These were used to protect the

sensor from unwanted movement during shipping.

6. Place the funnel portion back over the sensor and re-secure the locking tabs.

Power

Funnel

Battery Cover

Locking Tab

Remove piece under

rocker of rain sensor

Position Rain Sensor

LTV-R2 Rain Sensor

Lets identify the parts of the rain sensor.

• Mount your rain sensor in an open area for a more accurate rain count.

• Placing the rain sensor on the ground provides the most accurate rainfall measurement as there is no

wind shear. Unfortunately, since insects think of rain sensors as personal hotels, placing your sensor

3-6 feet above ground may deter the insects.

• This is a self-emptying sensor, but be sure your unit is not sitting in a depression that would prevent

rain from draining out of the bottom

• Your rain sensor should be accessible to allow for periodic cleaning of leaves or other debris that may

clog the funnel.

• Install the Rain sensor on a level platform that is stationary and has a direct line of sight to your station.

• Insert mounting screws through the holes in the base of the rain sensor. Do not over tighten.

• Use the bubble level inside your sensor to be sure it is level.

• Avoid other wireless rain sensors as this can cause inaccuracy due to signal interference.

• The maximum wireless transmission range to the rain station is over 400 feet (121 meters) in open air,

not including walls or ﬂoors.

• For video instruction, please visit: http://bit.ly/Rain_SensorMounting

Top (Funnel)

Battery Cover

Locking Tabs

Rocker

Mounting Screw (3 total) Bubble Level

Produkt Specifikationer

Mærke:	La Crosse Technology
Kategori:	Ikke kategoriseret
Model:	LTV-R2

Har du brug for hjælp?

Hvis du har brug for hjælp til La Crosse Technology LTV-R2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret La Crosse Technology Manualer

La Crosse Technology LTV-WSDTH04 Manual

23 September 2024

La Crosse Technology WT-137U Manual

13 September 2024

La Crosse Technology WT-2191A Manual

10 September 2024

La Crosse Technology V16 Manual

9 September 2024

La Crosse Technology V61-11 Manual

7 September 2024

La Crosse Technology WS-9410U Manual

31 August 2024

La Crosse Technology TX60U-IT-D Manual

31 August 2024

La Crosse Technology TX141V4 Manual

29 August 2024

La Crosse Technology 724-1409 Manual

28 August 2024

La Crosse Technology LTV-R1 Manual

27 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vulcan 1048C Manual

16 Juni 2025

Playtive IAN 91495 Manual

16 Juni 2025

Playtive IAN 270612 Manual

16 Juni 2025

Playtive IAN 315026 Manual

16 Juni 2025

Playtive IAN 115585 Manual

16 Juni 2025

Playtive 10464 Manual

16 Juni 2025

Playtive HG03821 Manual

16 Juni 2025

Martin VC-Strip Manual

16 Juni 2025

Playtive HG06316 Manual

16 Juni 2025

Playtive HG05102 Manual

16 Juni 2025