La Crosse Technology WS-8120U-IT-BR Manual

La Crosse Technology Vejrstation WS-8120U-IT-BR

Læs gratis den danske manual til La Crosse Technology WS-8120U-IT-BR (3 sider) i kategorien Vejrstation. Denne vejledning er vurderet som hjælpsom af 54 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 27.5 anmeldelser. Har du et spørgsmål om La Crosse Technology WS-8120U-IT-BR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Model WS-8120U

Solar Wall Clock

QUICK SETUP GUIDE

LCD display Solar panels

Function keys

Battery cover

Wall mount

location

Foldable stands

Solar-powered Transmitter:

 Remote transmission of outdoor

temperature to the Solar Clock by 915

MHz signals

 LCD displays outdoor temperature data

 Recharge batteries by solar-powered

cells

 Wall mounting case

Note:

 The solar-powered temperature transmitter uses solar cells to

charge the rechargeable batteries (2 x AAA rechargeable batteries:

included).

 Those rechargeable batteries cannot be replaced.

SOLAR TRANSMITTER OPERATION MODES

Important:

Users need to press the reset key to activate the solar transmitter

and link the transmission to the Solar Station (receiver).

It is important to allow sufficient light to reach the solar panel while

activating the solar transmitter. Make sure the lights are on in the setup

room and the solar panel is facing a 60W light bulb or brighter - do not

cover with hands or other objects.

Solar transmitter RESET key:

The solar transmitter has 3 operations modes:

Normal Operation Mode:

 This mode occurs when the battery voltage is higher than 2.5V.

 The transmitter will measure and transmit the temperature data to

the solar wall clock every 8 seconds.

 The environment brightness is checked every 5 seconds

 If a dark environment is detected, it will measure and transmit the

temperature every 16s

Note: only use a small pointed pen to

press the RESET key to re-active the

transmitter into Normal Operation Mode.

Solar panel

RESET key

 If the battery voltage is dropped lower than 2.8V, it will measure and

transmit the temperature every 16s

 If battery voltage is dropped lower than 2.4V, will go into Idle mode

 If the solar transmitter is placed into a dark environment for 72

hours, will goes into Stop mode.

 If the user cover the solar cell for 10 seconds and press the reset

button, "StP" will be displayed on the LCD. Then the transmitter

enters STOP mode.

Idle Operation Mode:

 This mode occurs when the battery voltage drops lower than 2.4V

 LCD is turned off.

 Does not perform temperature measurement and transmission.

 The environment brightness is checked every 5 seconds

 If battery voltage is raised higher than 2.5V, will go into Normal

mode

 If the solar transmitter is placed into a dark environment for 72

hours, will goes into Stop mode.

Stop Operation Mode:

 This mode occurs when the solar transmitter is placed into a dark

environment for 72 hours or the user covers the solar cell for 10

seconds and presses the RESET button.

 The transmitter is in a standby state. The unit does not perform any

operations and LCD is off.

 Under a bright condition, press the reset button to wake up the

transmitter into normal operation mode (battery voltage is higher

than 2.5V).

 This is the most power saving mode.

TO INSTALL / REPLACE BATTERY IN THE SOLAR CLOCK

The Solar Clock can use either the included 2 x alkaline rechargeable

battery (charged by solar panel: included) or 2 x AA alkaline battery (non-

rechargeable; not included).

INITIAL SETUP

It is very important to follow these steps:

1. First, remove the label covering over the battery compartment on

the back.

2. Open the battery compartment, and MAKE SURE that the battery

switch is in the BATTERY position (not the SOLAR position).

Battery switch in the BATTERY position

3. Now locate the battery insulator tab, and gently pull to remove it.

4. Slide the battery switch to the SOLAR position

5. Battery switch in the SOLAR position

6. Continue to section titled “Setup After Changing/Installing the

Battery in the Solar Clock ”

TO INSTALL / REPLACE BATTERY

The included alkaline rechargeable batteries should provide you with

many years of service. If your batteries need to be replaced, we suggest

you use 2 fully charged the AA Alkaline.

Rechargeable batteries should be fully charged before inserting into clock.

Alkaline rechargeable batteries must be used.

If you choose to use non-rechargeable batteries, the battery switch MUST

be moved to the BATTERY position (not the SOLAR position). In this

position, the solar cells do not charge the batteries.

REGARDLESS OF THE TYPE OF BATTERIES INSTALLED, THE

BATTERY SWITCH MUST BE IN THE BATTERY POSITION WHEN

THE BATTERIES ARE INSERTED.

If rechargeable batteries are used, the Battery switch should be moved to

the SOLAR position AFTER it is has been inserted.

To use non-rechargeable alkaline batteries:

1. Remove the included rechargeable AA batteries from the

compartment.

2. Use the switch to select the alkaline battery (see below).

3. Insert the batteries into the compartment, observing the correct

polarity (see marking inside battery compartment.

4. Replace battery cover

Note: For best performance, batteries should be replaced at least once

every 2 years to maintain the best running accuracy. Ensure that the

batteries used are new and the correct size.

Use switch to

select which type

of battery will be

used before

inserting the

battery into the

compartment

Battery

compartment

cover

Please help in the preservation of the environment and

return used batteries to an authorized depot.

SETUP AFTER CHANGING/REPLACING THE BATTERY IN THE

SOLAR CLOCK

1. After powering up the Solar Clock, all LCD segments will light up

briefly and it will show the time (12:00), indoor temperature, date,

and indoor humidity.

2. After the batteries are inserted, the Solar Clock will start receiving

data signal from the solar transmitter. The outdoor temperature data

should then be displayed on the Solar Clock. If this does not happen

after 2 minutes, the batteries will need to be removed from both

units and reset from step 1.

3. The distance between the Solar Clock and the transmitter should

not be more than 200 feet (60m) to ensure sufficient 915 MHz

transmission. (see notes on “Positioning” and “915 MHz

Reception”).

Note: When changing the battery:

1. Be careful that it does not spring free from the contacts.

2. Press any button 20 times with the battery removed.

3. Always wait at least 10 minutes after removing battery before

re-inserting; otherwise start up problems may occur.

TO SET THE TIME

Note: the time will be displayed with “AM” or “ ”PM for the time from 12:00

until 11:59.

1. Press and hold the SET key for 3 seconds to enter the time setting

mode.

2. The hour digits will start flashing.

Rechargeable Alkaline

battery switch position

Primary Alkaline

battery switch position

3. Set the desired hours by pressing and releasing the + key followed

by pressing the SET key.

4. Now the minute digits will start flashing.

5. Set the desired minutes by pressing and releasing the + key. If the +

key is held, the units will increase by 5.

6. Press the SET key again to confirm and enter the Solar Mode

setting.

SOLAR MODE

The Solar Mode is used for saving the power consumption of the

rechargeable battery (Default setting ON):

1. The characters “ON” or “OFF” will start flashing. By use of the +

key select “ON” “OFF” or to set the solar mode.

2. Press and release the SET key to exit the setting mode and switch

back to the normal display mode.

If the solar mode setting is ON:

 The surrounding environment brightness is checked every 5

seconds

 LCD will automatically turn OFF if the environment is too dark

 LCD will automatically turn ON if the environment is bright enough

 No information will be displayed when the LCD is OFF, but all the

settings and operations will remain, except for the temperature

and humidity measurements.

If the solar mode setting is OFF:

 LCD will remain ON constantly.

STOP MODE

If the Solar Clock is placed in a dark environment for 72 hours continually,

the clock will go to the stop mode:

 The most power saving condition.

 The Solar Clock will not perform any operation and the LCD will also

be OFF.

 Users need to press any key to wake up the Solar Station and to re-

activate the transmission with the solar transmitter.

VIEW MIN/MAX READINGS:

Press and release the PLUS button to view outdoor MIN/MAX readings,

then indoor MIN/MAX readings then return to the normal display.

RESET MIN/MAX READINGS:

Press and hold the PLUS button for 5 seconds to reset both Indoor and

Outdoor MIN/MAX readings to current temperature.

DISPLAY MODES:

Press and release the SET button to change the way the temperatures

are displayed on the weather station:

 Shows: Outdoor temperature in the first line on the left side.

Shows: Indoor temperature in the first line on the right side and

Indoor humidity in the second line on the right side.

 Shows: Indoor temperature in the first line on the left side and

Indoor humidity in the first line on the right side.

Shows: Outdoor temperature in the second line on the left side.

915MHZ RECEPTION CHECK FOR OUTDOOR SOLAR

TRANSMITTER

The Solar Clock will receive the outdoor data every 48 seconds. If the

temperature data is not being received 2 minutes after setting up (or the

display shows “- - -”), then please check the following points:

1. The distance of the Solar Clock or outdoor transmitter should be at

least 6 feet (2 meters) away from any interfering sources such as

computer monitors or TV sets.

2. Avoid placing the receiver onto or in the immediate proximity of

metal window frames.

3. Using other electrical products such as headphones or speakers

operating on the same signal frequency (915MHz) may prevent

correct signal transmission and reception.

4. Neighbors using electrical devices operating on the 915MHz signal

frequency can also cause interference.

Note: When the 915 MHz signal is received correctly, do not re-open the

battery cover of the Solar Clock, as the batteries may spring free from the

contacts and force a false reset. Should this happen accidentally then

reset all units (see “TO INSTALL / REPLACE BATTERY IN THE SOLAR

CLOCK” and “INITIAL SETUP” above) otherwise transmission problems

may occur.

The maximum transmission range is 200 feet (60 m) from the outdoor

transmitter to the Solar Clock (in open space). However, this depends on

the surrounding environment and interference levels. If no reception is

possible despite the observation of these factors, all system units have to

be reset (see “TO INSTALL / REPLACE BATTERY IN THE SOLAR

CLOCK” and “INITIAL SETUP”).

POSITIONING THE SOLAR CLOCK:

Before permanently mounting, ensure that the Solar Clock is able to

receive 915MHz signals from the desired location. In addition, the Solar

Clock should be placed in a bright environment for the rechargeable

batteries to be able to recharge.

There are two possible ways to mount the solar clock:

 use of the foldable table stands, or

 wall mounting

WALL MOUNTING

1. Install a mounting screw (not included) into a

wall—leaving approximately 3/16 of an inch

(5mm) extended from the wall.

2. Place the Solar Clock onto the screw, using the

hanging hole on the backside. Gently pull the

Solar Clock down to lock the screw into place.

Note: Always ensure that the Solar Clock locks onto

the screw before releasing.

POSITIONING THE SOLAR TRANSMITTER:

It is important to place the solar transmitter in a bright environment for the

rechargeable batteries to be able to recharge.

The solar transmitter can be placed onto any flat surface or wall mounted

using the bracket which doubles as a stand or wall mount base.

To wall mount: Secure the bracket onto a desired wall using the screws

and plastic anchors.

Clip the solar transmitter onto the bracket.

Note: The mounting surface can affect the transmission range.

If, for instance, the unit is attached to a piece of metal, it may

then either reduce or increase the transmitting range. For this

reason, we recommend not to place the unit on any metal

surfaces or in any position where a large metal or highly

polished surface is in the immediate vicinity (garage doors,

double glazing, etc.). Before securing in place, please ensure

that the Solar Clock can receive the 915MHz signal from the

solar transmitter at the positions that you wish to place them.

WARRANTY INFORMATION

La Crosse Technology, Ltd provides a 1-year limited warranty on this product

against manufacturing defects in materials and workmanship.

This limited warranty begins on the original date of purchase, is valid only on

products purchased and used in North America and only to the original

purchaser of this product. To receive warranty service, the purchaser must

contact La Crosse Technology, Ltd for problem determination and service

procedures. Warranty service can only be performed by a La Crosse

Technology, Ltd authorized service center. The original dated bill of sale must

be presented upon request as proof of purchase to La Crosse Technology, Ltd

or La Crosse Technology, Ltd’s authorized service center.

Produkt Specifikationer

Mærke:	La Crosse Technology
Kategori:	Vejrstation
Model:	WS-8120U-IT-BR

Har du brug for hjælp?

Hvis du har brug for hjælp til La Crosse Technology WS-8120U-IT-BR stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vejrstation La Crosse Technology Manualer

La Crosse Technology TX145WSDR Manual

31 Juli 2025

La Crosse Technology 328-1415 Manual

31 Juli 2025

La Crosse Technology 308-1711BLV3 Manual

31 Juli 2025

La Crosse Technology 308-10847 Manual

21 Juli 2025

La Crosse Technology CA73071 Manual

4 Marts 2025

La Crosse Technology M71633 Manual

8 Januar 2025

La Crosse Technology V41CA Manual

8 Januar 2025

La Crosse Technology CA74177 Manual

26 December 2024

La Crosse Technology S73071 Manual

26 December 2024

La Crosse Technology 308-1415FCT-NH Manual

26 December 2024

Vejrstation Manualer

Nyeste Vejrstation Manualer

Hyundai WS 2303 Manual

10 August 2025

TFA 30.3039 Manual

8 August 2025

TFA Linea Plus 35.1144.01 Manual

7 August 2025

TFA 98.1111.02 Manual

7 August 2025

TFA 30.3900.02 Manual

7 August 2025

TFA View 35.1142 Manual

7 August 2025

Brandson 307346 Manual

5 August 2025

Techno Line WS 9130 Manual

3 August 2025

Theben LUXORliving M140 Manual

3 August 2025

Techno Line WS 9215 Manual

3 August 2025