Makita HR2475 Manual

Makita Boremaskine HR2475

Læs gratis den danske manual til Makita HR2475 (28 sider) i kategorien Boremaskine. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Makita HR2475, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/28

INSTRUCTION MANUAL

MANUEL D'INSTRUCTION

MANUAL DE INSTRUCCIONES

DOUBLE INSULATION

DOUBLE ISOLATION

DOBLE AISLAMIENTO

Combination Hammer

Marteau combiné

Martillo combinado

HR2475

010154

ENGLISH

SPECIFICATIONS

Model HR2475

Concrete 25 mm (1")

Core bit 54 mm (2-1/8")

Steel 13 mm (1/2")

Capacities

Wood 32 mm (1-1/4")

No load speed (RPM) 0 - 1,100/min.

Blows per minute 0 - 4,500

Overall length 429 mm (16-7/8")

Net weight 3.0 kg ( 6.6 lbs)

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

GEA008-1

General Power Tool Safety

Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical Safety

4. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of an

GFCI reduces the risk of electric shock.

Personal Safety

10. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

11. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

12. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. . Carrying power tools

with your finger on the switch or energising power

tools that have the switch on invites accidents.

13. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

14. Do not overreach. Keep proper footing and

balance at all times. This enables better control

Produkt Specifikationer

Mærke:	Makita
Kategori:	Boremaskine
Model:	HR2475
Vægt:	3000 g
Produktfarve:	Grøn
Pakkevægt:	5500 g
Borepatron type:	SDS-plus
Strømkilde:	Vekselstrøm
Soft greb:	Ja
Bæretaske:	Ja
Antal gear:	3
Bore diameter, beton (maks.):	25.4 mm
Boring:	Ja
Slagboring:	Ja
Energi ved slagkraft:	2.7 J
Vurderet hastighed:	1100 rpm
Slagkraft:	4500 bpm or slag i minuttet
Hjælpehåndtag:	Ja
Nominel hastighed (min.):	0 rpm
Spændepatron:	Ingen
Mejsel inkluderet:	Ja
Optimale antal apparater i beton:	9.5 - 12.7 mm
Strømstyrke:	7 A