Mikrotik RB3011UIAS-RM Manual

Mikrotik Router RB3011UIAS-RM

Læs gratis den danske manual til Mikrotik RB3011UIAS-RM (3 sider) i kategorien Router. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Mikrotik RB3011UIAS-RM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

RouterBOARD 3011U series

Quick Setup Guide and Warranty Information

The RB3011U is a small form factor router with 10 Gigabit Ethernet ports and an SFP cage.It is configured out of

the box, you can simply plug in your internet cable and start using wireless internet. RB3011UiAS-RM comes in a

rackmount case, the RB3011UiAS-2HnD-IN comes in a desktop case and also includes a wireless access point

feature.

We recommend you to set up a password to secure your device, follow these steps

First use

1. Connect your Internet cable to port 1, and local network PCs to ports 2-10

2. Set your computer IP configuration to automatic (DHCP)

3. Wireless “access point” mode is enabled by default, connect to the wireless network name which starts

with “MikroTik”. Log into your router and configure a the Wireless password and router password to secure

your wireless network and access to the router

4. Default IP address from the local network is 192.168.88.1, open this address in your web browser to start

configuration. The username is and there is admin no password

Powering

The device accepts powering from either the power jack, or from the LAN1 Ethernet port:

Direct-input power jack (5.5mm outside and 2mm inside diameter, female, pin positive plug) accepts

14-30V DC (overvoltage protection starts at 30V).

 Eth1 port accepts 14-30V DC input (at the board; higher voltage needed to compensate for power loss on

long cables) from non-standard (passive) Power over Ethernet injectors. The board work withdoes not

IEEE802.3af compliant 48V power injectors

 A 110/220V PSU and a PoE injector is included

Extension Slots and Ports

 Ten 10/100/1000 (Gigabit) Ethernet ports (Auto MDI/X)

 One 8-30V DC power jack

 SFP port for SFP module (module not included, works only with Gigabit modules)

 (only on RB3011UiAS-2HnD-IN) built in wireless AP (2GHz , 802.11b/g/n), with external antennas.

 The Ether10 port suports PoE output, with auto detection feature. This means you can connect Laptops

and other non-PoE devices without damaging them. The PoE on Ether10 outputs approximately 2V below

input voltage, and supports up to 0.5A (So provided 24V PSU will provide 22V/0.5A output to the Ether10

PoE port).

Resetting the device

In case you wish to return the device to its original configuration, you can use the RESET button. Hold this button

during boot time until LED lights start flashing, then release the button to reset RouterOS configuration. You can

use this procedure if you have forgotten the password to access the device, or simply wish to return the unit to its

default configuration state.

See www.routerboard.com for more informaon. Contact for support quesons. 27/10/14support@mikrok.com

Produkt Specifikationer

Mærke:	Mikrotik
Kategori:	Router
Model:	RB3011UIAS-RM
Bredde:	443 mm
Dybde:	92 mm
Højde:	44 mm
Vægt:	- g
Produktfarve:	Sort
Ethernet LAN-porte (RJ-45):	10
Ethernet LAN:	Ja
Strømforbrug (typisk):	10 W
Driftstemperatur (T-T):	-30 - 70 °C
Ethernet LAN-datahastigheder:	10,100,1000 Mbit/s
Intern hukommelse:	1024 MB
Ethernet WAN:	Ja
Kabelteknologi:	10/100/1000Base-T(X)
USB version:	3.2 Gen 1 (3.1 Gen 1)
Antal USB-porte:	1
Strøm over Ethernet (PoE):	Ja
Ethernet-grænsefladetype:	Gigabit Ethernet
Stativ-montering:	Ja
Rackkapacitet:	1U