Mikrotik RB953GS-5HnT-RP-US Manual

Mikrotik Router RB953GS-5HnT-RP-US

Læs gratis den danske manual til Mikrotik RB953GS-5HnT-RP-US (10 sider) i kategorien Router. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Mikrotik RB953GS-5HnT-RP-US, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

RouterBOARD 953GS-5HnT

Quick Setup Guide and Warranty Information

The RB953 is equipped with three Gigabit Ethernet ports, two SFP cages and two miniPCI slots. It also has a built-

in 5GHz wireless device with three-chain support (three antenna connectors).

Assembling the Hardware

First use of the board:

1. Insert the miniPCI cards

2. Install the board in a case and connect antenna cables

3. Connect other peripherals and cables

4. Plug in PoE powered Ethernet to turn on the board

The device comes with a thermal pad, which is located inside a small bag. This thermal pad will ensure heat

transfer between the backside of RB953 wireless device heatsink, and the indoor or outdoor case, where it will be

mounted. The thermal pad should be put on the rectangular area of the RB953 heatsink, so that it is pressing

against the device case, when it is mounted.

Powering

It’s possible to power the device with the following methods:

 The first Ethernet port (Ether1) accepts 8-30V DC input (at the board; higher voltage needed to compensate

for power loss on long cables; at least 18V suggested) from non-standard (passive) Power over Ethernet

injectors. This device does work with IEEE802.3af compliant 48V power injectors. not

 DC power jack which accepts 8-30V (5.5mm outside and 2mm inside diameter, female, pin positive plug)

Booting process

RouterOS is the operating system of all RouterBOARD routers. Please see detailed configuration guide

here: http://wiki.mikrotik.com/wiki/Category:Manual

First, RouterBOOT loader is started. It displays some useful information on the onboard RS232C asynchronous

serial port. The serial port is set by default to 115200bit/s, 8 data bits, 1 stop bit, no parity.

The RouterOS system will then load. It will be also indicated by two beeps. Winbox or a web browser should be

used to connect to the default IP address of with the username and .192.168.88.1 admin no password

In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of

the device when starting it until the LED light turns off, and it will start to look for Netinstall servers.

In case IP connection is not available, Winbox can also be used to connect to the MAC address of the device. More

information here: http://wiki.mikrotik.com/wiki/First_time_startup

See for more information. Contact www.routerboard.com support@mikrotik.com for support questions. 10/07/17

Produkt Specifikationer

Mærke:	Mikrotik
Kategori:	Router
Model:	RB953GS-5HnT-RP-US
Bredde:	183 mm
Dybde:	105 mm
Højde:	24 mm
Produktfarve:	Flerfarvet
USB-port:	Ja
Ethernet LAN-porte (RJ-45):	3
Antal USB 2.0-porte:	1
Ethernet LAN:	Ja
Wi-Fi-standarder:	802.11a,Wi-Fi 4 (802.11n)
Processorkerner:	1
Driftstemperatur (T-T):	-40 - 70 °C
Ethernet LAN-datahastigheder:	10,100,1000 Mbit/s
SIM-kort slot:	Ja
Bedste Wi-Fi standard:	Wi-Fi 4 (802.11n)
WLAN dataoverførselshastighed (maks):	54 Mbit/s
Ethernet LAN-grænsefladetype:	Gigabit Ethernet
Hukommelseskortstik:	Ingen
Knap til nulstilling:	Ja
Strømkilde type:	PoE
Processorfrekvens:	720 Mhz
Frekvensbånd:	5.170-5.250, 5.725-5.835 GHz
Processormodel:	Qualcomm Atheros QCA9558
Strøm over Ethernet (PoE):	Ja
Indbygget processer:	Ja