Mikrotik RBM11G Manual

Mikrotik Router RBM11G

Læs gratis den danske manual til Mikrotik RBM11G (4 sider) i kategorien Router. Denne vejledning er vurderet som hjælpsom af 71 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 36 anmeldelser. Har du et spørgsmål om Mikrotik RBM11G, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

RBM11G

RBM11GRBM11G

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.

The Installation of the equipment must comply with local and national electrical codes.

This product is intended to be mounted outdoors on a pole but can also be installed indoors. Please read the mounting instructions carefully before

beginning installation. Failure to use the correct hardware and configuration or to follow the correct procedures could result in a hazardous situation to

people and damage to the system.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

First use

Insert the miniPCIe card (not included), please see paragraph .MiniPCIe slot

(Optional) Install the device in a case.

Connect antenna cables to the miniPCIe card and an Ethernet cable to the gigabit Ethernet port.

Plug-in power cable to turn on the device.

We recommend connecting to the device using Winbox with a default IP address of 192.168.88.1 with the username admin and no password (or,

.for some models, check user and wireless passwords on the sticker)

Mounting

M11G router for professional use. Each of the devices comes in ESD protective packaging. When handling electrical equipment please observe the

following safety precautions:

Use a wrist grounding strap when unpacking and working with electrical components to avoid electrical discharge (ESD) damage.

After unpacking please place the router on the anti-static mat.

When mounting unit make sure there are no objects that can damage or touch the PCB plate.

Note that ETH and DC jack is extending over the perimeter of the PCB plate.

The device can be mounted in your desired location using the factory provided four holes in a PCB plate, located on each side of the device.

MiniPCIe slot

Installing a miniPCIe module should be done by a qualified person, please follow safety precautions when handling electrical equipment:

Place the device on the anti-static mat.

Locate the miniPCIe slot and remove two factory attached screws.

Attach provided a thick thermal pad to the card, and install the card into miniPCIe slot so that the thermal pad is between PCB and card.

The secure card in place using previously removed two screws.

Attach the grey uFL connector to the MAIN antenna connector of the modem, attach the black cable to the secondary (or AUX) connector.

Attach a thinner thermal pad to the top of the card.

Mount unit in your desired location.

After you mounted the device, slide in the SIM card from your mobile operator into the SIM slot, with the chip facing down. The slot accepts miniSIM (2FF).

Powering

The device accepts power with the following modes:

Passive 10-30 V PoE to Ethernet port. The Higher voltage needed to compensate for power loss on long cables. At least 18 V is suggested.

Direct input to the power jack 10-30 V.

Maximum power consumption 11 W.

Booting process

RouterOS is the operating system of all RouterBOARD routers. Please see documentation here: https://mt.lv/help

This device is not preconfigured other than an IP address on the Ethernet port. Another configuration has to be applied according to the documentation

manual linked above.

The Initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility. Winbox should be used to connect to the default IP address

of 192.168.88.1 with the username admin and no password.

In case you wish to boot the device from the network, for example, to use MikroTik Netinstall, hold the reset button of the device when starting it until the

LED light turns off, and the device will start to look for Netinstall servers.

In case the IP connection is not available, the Winbox utility can also be used to connect to the MAC address of the device. More information in the

documentation.

Extension slots and ports

One gigabit Ethernet port (With Auto MDI/X so you can use either straight or cross-over cables for connecting to other network devices). The

Ethernet port accepts 10-30V DC powering from a passive PoE injector.

miniPCIe slot for either an 802.11 wireless card or a 3G/LTE modem. SIM slot is available for miniPCIe 3G/LTE modems and has no functionality

when a modem is not installed.

Buttons and jumpers

RouterBOOT reset button has the following functions:

Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds).

Keep holding for 5 more seconds, LED turns solid, release now to turn on CAPs mode (total 10 seconds).

* Keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15

seconds).

Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.

Useful for RouterBOOT debugging and recovery.

Specifications

For more information about this product, specification and pictures please visit our web page: https://mikrotik.com/product/m11g

Operating system support

The device supports RouterOS software version 6. The specific factory-installed version number is indicated in the RouterOS menu /system resource.

Other operating systems have not been tested.

MikroTik mobile app

Produkt Specifikationer

Mærke:	Mikrotik
Kategori:	Router
Model:	RBM11G
Bredde:	105 mm
Dybde:	110 mm
Vægt:	- g
Produktfarve:	Black, Green, Grey
Ethernet LAN-porte (RJ-45):	1
Ethernet LAN:	Ja
Processorkerner:	2
Driftstemperatur (T-T):	-40 - 70 °C
Ethernet LAN-datahastigheder:	10,100,1000 Mbit/s
Intern hukommelse:	256 MB
Operativsystem installeret:	RouterOS
DC-in-stik:	Ja
Strømkilde type:	PoE
Harmoniseret systemkode (HS):	85176990
Processorfrekvens:	880 Mhz
Processortråde:	4
Lagermedie:	Flash
Processormodel:	MediaTek MT7621A
Flashhukommelse:	16 MB
Strøm over Ethernet (PoE):	Ja
Indbygget processer:	Ja