Navman MiVue SmartBox III Manual

Navman Ikke kategoriseret MiVue SmartBox III

Læs gratis den danske manual til Navman MiVue SmartBox III (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Navman MiVue SmartBox III, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Introduction
Navman Smart Box III provides power to your Navman dash cam by connecting with the constant power of the
fuse terminal of your vehicle. It is very useful when you want to record video footage whilst parking. The Smart
Box III can prevent the discharge of the vehicle battery by blocking the electric power automatically as it checks
the voltage and preset timer.
Parts and functions
14
2 3
1 Fuse cable
- ACC (red wire)
- B+ (yellow wire)
- GND (black wire)
2 Setting switches
- Switch 1 and 2: Voltage
- Switch 3 and 4: Timer
3 LED indicator
4 Mini-USB connector*
Connects to the dash cam.
* The type of the connector may vary by model.
Installation and setup
1. Set up the voltage and timer by adjusting the switches.
Setting up the voltage:
1 ON / 2 ON
12.6V
25.2V
(Passenger car/RV)
(Truck/bus)
1 OFF / 2 ON
12.4V
24.8V
1 ON / 2 OFF
12.2V
24.4V
1 OFF / 2 OFF
12.0V
24.0V
The Smart Box III is designed to power the dash cam by drawing power from the car's battery until it reaches
a specific voltage limit. Once the car's battery falls lower than this level, the Smart Box III will automatically
stop drawing power from the car's battery.
It is recommended to set the Smart Box III to 12.2V (for passenger car and RV) / 24.4V (for truck and bus),
and only change it to the other setting options after checking with your car's manufacturer and/or car’s
battery. Please contact your car's manufacturer and/or car’s battery manufacturer for more information
relating to the minimum battery voltage required for your vehicle.
Setting up the timer:
3 ON / 4 ON
Power off
3 OFF / 4 ON
6 hours
3 ON / 4 OFF
12 hours
3 OFF / 4 OFF
24 hours
If the time passes the preset timer (by checking the time after vehicle ignition is turned off), the power to the
dash cam will be disconnected automatically.
Select either 6 / 12 / 24 hours to enable the uninterrupted power function of the Smart Box III and the
dash cam will be powered even when the vehicle engine stops.
If is selected, the uninterrupted power function of the Smart Box III will be disabled and the Power off
dash cam will be powered only when the vehicle engine is started.
If you adjust any of the voltage/timer switches whilst your vehicle is on, you need to restart the Smart Box
III by turning the vehicle off and back on again for the settings to take effect.
2. Locate and open the fuse box inside of the vehicle.
Please note that the installation illustrations are for your reference only. The placement of the fuse box may
vary depending on the vehicle model. If you encounter any problems during installation, it is recommended
that you contact a skilled installer (e.g. the service personnel of the vehicle or authorised car technician) for
assistance and installation.
3. Check and confirm the vehicle's voltage by using the electricity tester as battery voltages varies by vehicle.
You must confirm your vehicle's voltage.
Use the electricity tester to locate the fuse from which the power is supplied even when the vehicle is turned
off, such as the emergency flashing hazard lights, interior and door lights etc. Connect the yellow wire (B+) to
the fuse.
Use the electricity tester to locate the fuse from which the power is not supplied when the vehicle is turned
off, such as the indicator lights. Connect the red wire (ACC) to the fuse.
The black wire (GND) must be connected to the metal part of the vehicle for grounding. If not grounded, this
product may not work properly. You can use a screw to attach the black wire to the vehicle (try to find a screw
hole on any metal part).
Connect the Smart Box III to the dash cam and confirm it is working properly by the LED indicator that glows
in green. Then you can arrange the cable and complete the installation.
You can route the cable through the top ceiling and the A-pillar so that it does not interfere with driving. Make
sure that the cable installation does not interfere with the vehicle airbags or other safety features.
Precautions and notices
Rated input voltage: DC 12 – 24V, output current: 2A maximum
WARNING! Do not use other than rated output voltage status. This product can only be used with the vehicles
that have DC 12 – 24V voltage. (Passenger car and RV: 12V; truck and bus: 24V)
Follow the installation instructions or ask a specialist technician for assistance.
There may be deviations in vehicle power voltages about vehicle battery status and usage environments.
Never attempt to disassemble, repair or make any modifications to the product. Disassembling, modifying or
any attempt to repair could cause damage to your device, may inflict bodily harm or damage to property and
will void any warranty.
You must use the product as intended. Misuses, neglect, accident or abuse will not cover the warranty,
replacement or refund.
Do not drop the product or subject it to severe shock.
When installing, mounting and storing, please do so in a dry place.
Please check the installation and operation of the product regularly.
The manufacturer is not responsible for any damages caused by not observing the above warnings and
precautions.
1-Year Limited Warranty
1. DEFINED TERMS.
In this document:
(a) "Australian Consumer Law" means the Australian Consumer Law set out in Schedule 2 to the Competition
and Consumer Act 2010 (Cth).
(b) "Consumer Guarantees" means the consumer guarantees which apply to the supply of products or services
under: (A) the Australian Consumer Law, as amended from time to time, or other similar legislation of a state
or territory of Australia; and (B) the New Zealand Consumer Law or other similar legislation.
(c) "Customer" means the purchaser of a Navman product.
(d) "Navman Warranty" has the meaning given in section 2 of this document.
(e) "New Zealand Consumer Law" means the Consumer Guarantees Act 1993 and Fair Trading Act 1986, as
amended from time to time.
2. NAVMAN WARRANTY.
(a) The Navman Warranty provides benefits which are in addition to other rights and remedies the Customer
has under law. This document does not limit, restrict or exclude any rights that a person has because of the
Consumer Guarantees.
(b) In addition to any rights that a Customer or any other person has because of the Consumer Guarantees, and
subject to section 5 of this document, MiTAC Australia Pty Ltd, in Australia, and Navman Technology NZ
Ltd, in New Zealand. (both "Navman") warrants that:
(i) The hardware device ("Hardware") will be free of defects in material and workmanship and will conform
to their published specifications; and
(ii) its software products and software provided with the Hardware (collectively, "Software") will be free
from media defects and will substantially conform to the thencurrent user documentation provided with
the Software (including updates thereto), in each case for a period of one year from the date of original
purchase ("Warranty Period") (the "Navman Warranty").
(c) Where Hardware or Software is repaired or replaced under this Navman Warranty, the Navman Warranty
will apply to the repaired or replaced Hardware or Software for the longer of:
(i) 90 days from the date of return shipment of that repaired or replaced Hardware; and
(ii) the balance of the original Warranty Period applying to that Hardware or Software (or the Hardware or
Software it replaces).
(d) Customers must make their own enquiries to determine whether the Software will meet their requirements,
and except where otherwise required by the Consumer Guarantees:
(i) Navman does not warrant that the Software will meet a Customer's requirements or that its operation
will be uninterrupted, error-free or virus-free; and
(ii) Customers assume the entire risk of using the Software.
3. CUSTOMER’S REMEDY.
(a) In addition to any rights under the Consumer Guarantees, if:
(i) the Hardware or Software is defective in contravention of the Navman Warranty or otherwise fails to
conform to the requirements of the Navman Warranty; and
(ii) on or before the last day of the Warranty Period, the Customer sends the affected product to Navman
(and retains proof of shipping),

Produkt Specifikationer

Mærke: Navman
Kategori: Ikke kategoriseret
Model: MiVue SmartBox III

Har du brug for hjælp?

Hvis du har brug for hjælp til Navman MiVue SmartBox III stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Navman Manualer

Navman

Navman MiVue KUBE Manual

8 Oktober 2025
Navman

Navman MiVue True 4K PRO Surround Manual

13 August 2025
Navman

Navman MiVue 270 SAFETY Manual

13 August 2025
Navman

Navman MiVue True 4K DC Manual

12 August 2025
Navman

Navman MiVue True 4K Manual

12 August 2025
Navman

Navman MiVue 930 DC Manual

5 August 2025
Navman

Navman MiVue Drive LM Manual

2 August 2025
Navman

Navman MiVue 100 Manual

2 August 2025
Navman

Navman MiVue 388 Manual

2 August 2025
Navman

Navman MiCam Truck Manual

2 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Pentax

Pentax IQZoom 130-M Manual

15 November 2025
IFM

IFM EBC024 Manual

15 November 2025
StarTech.com

StarTech.com CK4-P204C Manual

15 November 2025
Zen Living

Zen Living 350133 Manual

15 November 2025
Televés

Televés Optical 237003 Manual

15 November 2025
Lucide

Lucide Lionel Manual

15 November 2025
ADATA

ADATA MA48V2K1-GSE-01 Manual

15 November 2025
Homedics

Homedics HST-100-EU Manual

15 November 2025
Homedics

Homedics Illumine ILS-ASN Manual

15 November 2025
Homedics

Homedics SBM-301MH Manual

15 November 2025