Nemco 55109 Manual

Nemco Ikke kategoriseret 55109

Læs gratis den danske manual til Nemco 55109 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Nemco 55109, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Operating and Maintenance Instructions

Model: 55050AN Spiral Fry™ Potato Cutter

55050AN-P Vegetable Noodler

55050AN-G Fine Cut Garnish Cutter

55050AN-R Ribbon Fry Cutter

55050AN-WR Wavy Cut Ribbon Fry Cutter

55050AN-CT Chip Twister

55050AN-WCT Wavy Chip Twister

IMPORTANT

1. To get the best operation and life from your machine, please read and comply with these instructions.

2. Clean machine thoroughly before and after each use using cleaning instructions below.

3. Minimize the use of alkaline cleaners as they may cause pitting and dulling of the finish.

SAFETY INSTRUCTIONS

Remember that the blades are VERY SHARP; be careful when handling and operating the machine to keep hands away from

the cutting edges.

PREPARATION

1. Remove the mounting base from the machine as it is received and install it on a tabletop. Insert the SUPPORT STAND into the

MOUNTING BASE and secure in place with the LOCK SCREW.

2. If unit fails to operate properly when first used call NEMCO customer service at 1-800-782-6761

OPERATION of Spiral Fry™

First disengage the DRIVE LEVER by lifting it off the DRIVE SCREW and letting it hang down from the SUPPORT ROD. Pull back on

CRANK until the back face of the DRIVE PLATE mounted on the rear of the DRIVE SCREW strikes the face of the stand. Push the

large diameter end of the product onto the fingers of the DRIVE PLATE and then push product, drive plate and crank forward until

CENTER SCREW is embedded in the product. Engage DRIVE LEVER by placing it over the DRIVE SCREW. Then turn CRANK

clockwise until product is completely processed. Disengage DRIVE LEVER, pull DRIVE SCREW back, remove product heel and

repeat the process.

Note: For best results, place a hand lightly on the DRIVE LEVER while turning the crank. When the DRIVE LEVER rises, stop

cranking; lift the DRIVE LEVER and pull the CRANK and DRIVE SCREW back to accept the next product. Do not continue

to crank after the DRIVE LEVER rises.

OPERATION OF RIBBON FRY, GARNISH CUTTER, & WAVY CUT

Pull back on CRANK until back face of the DRIVE PLATE mounted on the rear of the DRIVE SHAFT strikes the face of the STAND.

Push the large diameter end of the product on to the fingers of the DRIVE PLATE and then push the DRIVE PLATE and CRANK

forward until the round blade is embedded in the product. Then press the CRANK forward firmly while turning CRANK clockwise

until product is completely processed. The DRIVE LEVER is used on the spiral fry only.

CLEANING

Loosen LOCK SCREW and remove the machine from the MOUNTING BASE. The machine can be cleaned by immersing, pressure

spraying or putting it through a dishwasher.

When necessary, the machine can be easily disassembled for further cleaning as follows:

1. Remove FRONT PLATE ASSEMBLY by removing the WING NUTS.

2. The BLADES can be removed with a screwdriver. Note: CENTER SCREW has a LEFT HAND THREAD so turn

clockwise to remove.

3. Remove the DRIVE PLATE by unthreading it from the DRIVE SCREW.

4. The SUPPORT RODS can be unthreaded from the SUPPORT STAND ASSEMBLY.

5. To reassemble, reverse the procedure.

PREVENTATIVE MAINTENANCE

1. All BLADES are made of hardened Stainless Steel. They can be re-sharpened with a file or sharpening stone (except for Wavy

Cut).

2. Clean machine after each use.

SPIRAL FRY, RIBBON FRY, & WAVY FRY COOKING INSTRUCTIONS

Your new Spiral Fry is an excellent machine made of quality Stainless Steel, Aluminum and Engineered Plastics. This machine will

be one of the most profitable pieces of equipment in your kitchen. The quality of the potatoes served is directly related to the

selection of the potato, how it is stored, how it is prepared, how it is cooked and when it is served.

There are two methods of preparing your potato. One is to cut and cook to order. The other is to cut your potatoes in quantity in

advance, store or blanch, and then cook to order.

Produkt Specifikationer

Mærke:	Nemco
Kategori:	Ikke kategoriseret
Model:	55109

Har du brug for hjælp?

Hvis du har brug for hjælp til Nemco 55109 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Nemco Manualer

12 November 2025

11 November 2025

17 September 2025

26 August 2025

26 August 2025

26 August 2025

25 August 2025

25 August 2025

21 August 2024

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Tuftex 197561 Manual

12 November 2025

Zen Living 350158 Manual

12 November 2025

Amaran Octa Dome 90 Manual

12 November 2025

Heatfab Saf-T Liner 4608SS Manual

12 November 2025

Crew Dog Electronics Stratux ADS-B Dual Band Receiver Manual

12 November 2025

Mobility Lab ML313153 Manual

12 November 2025

MSW PRO-G 12M Manual

12 November 2025

ADATA MA48V2K5-NTE-01 Manual

12 November 2025

Hikvision DS-2TE127-G4A Manual

12 November 2025

Zotac GAMING GeForce RTX 2060 SUPER AMP Manual

12 November 2025