Nikon Pillar Stand with Adapter Manual

Nikon Kikkert Pillar Stand with Adapter

Læs gratis den danske manual til Nikon Pillar Stand with Adapter (2 sider) i kategorien Kikkert. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Nikon Pillar Stand with Adapter, eller vil du spørge andre brugere om produktet?

Side 1/2
Printed in Japan, 911C_1_1910
ピラースタンド(アダプター付き
使用説明書/Instruction manual
はじめに
このたびは、ニコン ピラースタンド アダプター付き をお買い上げい ( )
ただき、まことにありがとうございます。
製品をお使いになる前に本書をよくお読みになり、正しくお使いくだ
さい。
お読みになった後は、いつでも見られるところに保管してください。
使用説明書について
• 使用説明書の一部または全部を無断で転載することは、固くお断り
いたします。
• 本書のイラストは、実際と異なる場合があります。
• 使用説明書の誤りなどについての補償はご容赦ください。
• 製観、で、
ご了承ください。
安全上・使用上のご注
この使用説明書には、あなたや他の人々への危害や財産への損害を未
然に防ぎ、この製品を安全にお使いいただくために、守っていただき
たい事項を記載しています。内容をよく理解してから、製品をご使用
ください。
警告
この表示を無視して、誤った取り扱いをすると、人が死
亡または、重傷を負う可能性が想定される内容を示して
います。
注意
この表示を無視して、誤った取り扱いをすると、人が傷
害を負う可能性が想定される内容および、物的損害のみ
の発生が想定される内容を示しています。
警告
• この製品によじ登ったり、ぶら下がったり、強い衝撃を与えないで
ください。転倒する恐れがあります。
注意
• この製品の包装に使用されているポリ袋などを、小さなお子さまの
手の届くところに置かないでください。口や鼻をふさぎ、窒息の原
因になることがあります。
• お子さまが部品や付属を誤って飲み込まないよう注意ください
万一、飲み込んだ場合は、すぐに医師の診断を受けてください。
• この製品を不安定な場所に置かないでください。転倒により、けが
や破損の原因となることがあります。
• この製品は、長期間の使用や保管の間に劣化し、衣類などを汚すこ
とがあります。ご使用になる前に点検し、劣化による異常が見られ
た場合は、ニコンのサービス機関にご相談ください。
• この製品は重量があるため、組み立てるときに落としたり倒したり
しないでください。けがの原因となることがあります。
この製品を組み立てるときや、架台やアダプターを取り付けるとき
は、ボルトでしっかりと固定してください。
この製品に強い衝撃を与えないでください。衝撃により変形、破損
した場合は、すぐにお買い上げ店、またはニコンのサービス機関に
ご相談ください。
この製品を移動させる場合は、大型双眼望遠鏡本体及び架台を取り
外してください。移動後は、各種ボルトに緩みが無いか確認してく
ださい。
手入れ・保守について
この製品に雨、水滴、砂や泥がついたときは、柔らかい清潔な布で
速やかに拭き取るようにしてください。とくに、海辺等で使われる
ときは、湿った柔らかい清潔な布で塩分を拭き取り、次に乾いた布
で軽く拭いて乾かしてください。
ベンジンやシンナーなどの有機溶剤や、有機溶剤を含むクリーナー
などを汚れ落としに使わないでください。
アフターサービスについて
(
き を、安心してご愛用いただきますよう次のとおり修理、アフター)
サービスを行っております。
• 本製品の補修用性能部品 (
な部品 は、製造打ち切り後も 年間を目安に保有しております。) 8
ご使用いただいております製品が修理可能かどうかにつきまして
は、入店、まはニのサス機お問わせ
さい。
は、
ご案内」をご覧ください。
付記
水没災、落等にまた全損れる
は、修理が不可能となります。なお、この故障または破損の程度の
判定はニコンのサービス機関におまかせください。
構成品
支柱
台座
付きボルトM10x20 12
M10 20 4 M10 本)・ 用
六角レンチ
スタンド部
スタンドアダプター
架台取り付け用ワッシャー付き六角穴
付きボルト( M12 x 30 6 M12本)・ 用
六角レンチ
アダプター部
ご購は構
含まれない場合があります。
仕様
高さ(mm) 脚部 (mm)
(中心からの寸法) 質量(重さ)
(kg)
スタンド部 1,115 423 26.5
直径 厚さ 質量(重さ)(mm) (mm) (g)
アダプター部 184 12 850
Jp En
1. ピラースタンドの組み立て
1- ①脚部の組み立て
1. 2 台座に、他の 本の脚を組み付けます。
付属の 用六角レンチと六角穴付きボルト( )M10 M10 8 本を使って、
しっかりと組み付けてください。
その後、台座の脚頭に六角穴付きボルト( )M10 4 本を軽くねじ込み
ます。
2. 平らで強固な地面に、組み立てた脚部を設置します。
3. 脚のにあ平調ボルお手の適サイスパ
ナ等で回して、脚部が水平になるように設置します。
水平調用ボ先端にめ場合板な敷い
て、先端がめり込まないようにしてください。
1- ②脚部と支柱の組み立て
1. 1- -1 支柱下部のダルマ穴の大きい側に、手順 ① でセットしたボル
トをはめます。
2. 支柱頭に、ダの細にボ当たで支
柱を回します。
3. M10 用六角レンチで六角穴付きボルト( )を締め付けます。M10
2. 架台とピラースタンドの組み付け
2- ①架台とスタンドアダプターの組み立て
1. M12 架台とスタンドアダプターを、 用六角レンチとワッシャー付き
六角穴付きボルト( )M12 6 本を使って確実に固定します。
2. M10 スタンドアダプター下面の ボルト穴に六角穴付きボルト
( )M10 4 本を軽くねじ込んでおきます。
2- ②アダプター付き架台とピラースタンドの組み付け
1. 2- -2 支柱上部のダルマ穴の大きい側に、手順 ① でセットしたスタ
ンドアダプター下部の六角穴付きボルト( )をはめます。M10
2. 架台柱にら、穴の分にが当まで
架台を回します。
3. M10用六角レンチで六角穴付きボルト( )を締め付けます。M10
大型望遠体との取け手つい大型望遠
鏡本体の使用説明書を参照してください。
3. アダプター付き架台とピラースタンドの
取り外し
取り方法は ②逆で架台タンダプは組2-
たままにしておくことで、 回目以降の設置では ①を省略できます。2 2-
屋外に設置した場合は、使用後に大型双眼望遠鏡本体及び架台をピラー
スタンドから取り外して保管することをおすすめします。
Binocular Telescope Pillar Stand with Adapter
Instruction manual
Introduction
Thank you for purchasing the Nikon Binocular Telescope Pillar Stand with
Adapter.
Before using the product, read this manual thoroughly to ensure proper use.
After reading this manual, keep it in a readily accessible place for future refer-
ence.
About the manual
No part of the manual may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language in any form, by
any means, without Nikons prior written permission.
Illustrations shown in this manual may dier from the actual product.
Nikon will not be held liable for any errors this manual may contain.
The appearance, specications, and capabilities of this product are subject
to change without notice.
SAFETY AND OPERATION PRECAUTIONS
Strictly observe the guidelines contained in this manual in order to use this
product safely and prevent possible injury or property damage to you and
others. Understand the contents thoroughly for correct use of the product.
WARNING
This indicates that improper use by ignoring the con-
tents described herein can result in potential death or
serious injury.
CAUTION
This indicates that improper use by ignoring the con-
tents described herein can result in potential injury or
material loss.
WARNING
Do not climb on or hang from this product. Do not subject it to physical
shocks. Otherwise, it may tip over.
CAUTION
Keep the plastic bag used to wrap this product or other small parts out of
reach of children. The bag may block their mouths and noses and cause
them to suocate.
Be careful of children inadvertently swallowing small parts or accessories.
If children swallow such parts, see a doctor immediately.
Do not place this product on an unstable surface. Otherwise, it may fall
and cause personal injury or product damage.
The product may deteriorate when it is used or stored over a long period
of time, and deterioration may stain your clothes. Check the product be-
fore use, and if any defects due to deterioration are found, consult a Nikon
authorized service representative.
When assembling the product, exercise care not to drop or tilt it because
it is heavy. Failure to do so may cause personal injury.
When assembling the product or attaching the fork mount or adapter to
it, be sure to rmly secure them using bolts.
Do not subject the product to any physical shocks. If the product is de-
formed or damaged due to being subjected to shocks, consult your local
dealer or a Nikon authorized service representative immediately.
When moving the product, be sure to remove the binocular telescope
body and the fork mount. After moving it, check all bolts for looseness.
Care and maintenance precautions
If any rain, water, sand, or mud should come in contact with the product,
remove it using a soft, clean cloth as soon as possible. If using the product
at the seaside, wipe o any salt that may have adhered to the surface of
the body using a damp, soft, clean cloth, and then wipe it again using a
dry cloth.
Do not use benzene, thinner, or any other cleaners containing organic
solvents.
Components
Pillar
Base
Leg
M10x20 bolts (x12) used to
assemble the stand, M10x20
bolts (x4) used to attach the
stand adapter
Hexagonal key
Stand
Stand adapter
M12x30 bolts (x6) with washers used to
attach the fork mount, M12 hexagonal key
Adapter
* May be not included in the items supplied
depending on the purchased set.
Specifications
Height (mm/in.)
Leg section
Distance from the
center (mm/in.)
Weight (kg/oz.)
Stand 1,115/43.9 423/16.7 26.5/934.8
Diameter (mm/in.) Thickness (mm/in.) Weight (g/oz.)
Adapter 184/7.2 12/0.5 850/30.0
1. Assembling the pillar stand
1-(1) Assembling the leg section
1. Attach the other two legs to the base.
Firmly assemble them using the M10 hexagonal key and eight M10 hex
socket head cap bolts provided with the product.
Then, lightly screw the four M10 hex socket head cap bolts into the leg
head on the base.
Jp En
2. Place the assembled leg section on a rm, at surface.
3. Turn the leveling bolt on the end of each leg using a wrench of an
appropriate size to level the leg section.
If the ends of the leveling bolts sink into the ground, lay an iron plate to
prevent them from sinking into the ground.
1-2 Assembling the leg section and pillar
1. Insert the bolts you set in step 1-(1)-1 into the larger holes of the key-
holes at the lower part of the pillar.
2. Place the pillar on the leg head and turn the pillar until the bolts
enter the smaller holes of the keyholes.
3. Tighten the M10 hex socket head cap bolts using the M10 hexagonal
key.
2. Assembling the fork mount and pillar stand
2-(1) Assembling the fork mount and stand adapter
1. Assemble the fork mount and stand adapter.
Use the M12 hexagonal key, M12 hex socket head cap bolts, and six
washers to rmly secure them.
2. Lightly screw the four M10 hex socket head cap bolts into the M10
holes at the bottom of the stand adapter.
2-(2) Assembling the fork mount with the adapter and
pillar stand
1. Insert the M10 hex socket head cap bolts you set to the lower part of
the stand adapter in step 2-(1)-2 into the larger holes of the keyholes
at the upper part of the pillar.
2. After you have placed the fork mount on the pillar, turn the fork
mount until the bolts enter the smaller holes of the keyholes.
3. Tighten the M10 hex socket head cap bolts using the M10 hexagonal
key.
For the procedures to attach the binocular telescope body and the fork
mount, refer to the Nikon Binocular Telescope Body Instruction Manual.
3 Removing the fork mount with the adapter
and pillar stand
Reverse step 2-(2) to remove them. Keeping the fork mount and the adapter
in an assembled state will allow you to skip step 2-(1) for the second and
subsequent installations.
If the product is placed outdoors, we recommend that you remove the
binocular telescope body and fork mount from the pillar stand after use and
then store it.


Produkt Specifikationer

Mærke: Nikon
Kategori: Kikkert
Model: Pillar Stand with Adapter

Har du brug for hjælp?

Hvis du har brug for hjælp til Nikon Pillar Stand with Adapter stil et spørgsmål nedenfor, og andre brugere vil svare dig