Nissin Di622 Mark II Manual

Nissin Blitz Di622 Mark II

Læs gratis den danske manual til Nissin Di622 Mark II (6 sider) i kategorien Blitz. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om Nissin Di622 Mark II, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

for Canon EOS / Nikon digital SLR cameras

for Sony digital SLR cameras

INSTRUCTION MANUAL

Nissin Japan Ltd., Tokyo

http://www.nissin-japan.com

Nissin Marketing Ltd., Hong Kong

http://www.nissindigital.com

Nissin Di622 Mark II is designed for digital SLR cameras with hotshoe

and the latest TTL flash control technology.

Note: No film camera can be used with Di622 Mark II.

Attach Di622 Mark II to your camera, and then almost all jobs are

controlled by the camera for the most proper exposure.

Read this instruction manual and refer your canera owner’s manual to

enjoy flash photography.

The compatibility list of Di622 Mark II, please check at our official

website: www.nissindigital.com

WARNING

The flash unit contains high voltage electric parts. Do not try

to open or repair the flash unit. Return it back to the repair

service station or the store you bought it.

Do not touch the inside parts from the opening when the unit

was dropped and broken.

Do not fire the flash direct to the eye at short distance. It may

damage the eye. When taking flash picture especially

toward a baby, it is recommended to keep the flash unit at

least 1 meter (3.3feet) away from the subject.

Or use diffuser or bounce the light to the ceiling or to the wall

to soften its intensity.

Do not use the flash unit in the flammable gas, chemicals or

such liquids. It may cause fire or electric shock.

CAUTIONS

Do not leave or store the flash unit in the temperature over

40°C, such like in the automobile.

The flash unit is not water resistant. Keep the unit away from

rain, snow and humidity.

Do not use benzene, thinner or other alcoholic agents to

clean the unit.

Do not use this flash with the cameras which is not listed in

the compatibility list at our official website, otherwise it may

damage the camera’s circuitry.

Remove the batteries when not in use for a longer period of

time.

This sign refers the danger or serious damage.

This sign refers the damage or defect.

622II.Rev.0211.1.0

Design and Specifications are subject to change without prior notice.

Ch 1 G roup A

Names of the Components

Flash stand

Light diffusing panel / Fill-in reflector

Flash head

AF-assist light / wireless flash sensor

Lock ring

Mounting foot

Hotshoe contacts

X - Terminal

Pilot lamp (Test flash button)

Battery compartment door

Power switch (Press button)

Mode select button / indicator

(TTL Manual SD SF Wireless) → → → →

Flash power leveel indication lamp (6 LEDs)

Flash power level select button

Accessories: Flash stand, Pouch

Basic Operation

Inserting batteries

Open the battery compartment door and

insert 4 x size AA batteries as shown by

the picture.

Make sure the + and - battery contacts are

correctly inserted at the battery compart-

ment.

Close the battery compartment door and

slide it back in place.

NOTE

Wrong insertion or using different size batteries may result damage on the

flash unit.

It is recommended to use all 4 batteries in same brand and type, and

replace them all att p2-he same time.

Ch 1 Group A

ilo

On/O ﬀ

Ch 1 Grou p A

On/Oﬀ

Ch 1 Group A

ilo

On/O ﬀ

Mounting Di622 Mark II on the camera

Slide the mounting foot of Di622 Mark

II into the hotshoe of camera.

Twist the lock ring clockwise to tighten

it.

Twist the lock ring anti-clockwise to

loosen it as shown in the picture.

Removing Di622 Mark II from the camera

Loosen the lock ring and slide the mounting foot of Di622 Mark II off

the hotshoe of camera.

Before mounting or removing Di622 Mark II into or from the camera,

make sure to turn off the power switch of both Di622 Mark II and the

camera.

NOTE

Push the lever of the locking ring (in the

direction of the arrow) of Di622 Mark II

to loosen it as shown in the picture.

Slide the mounting foot of Di622 Mark

II into the hotshoe of the camera while

holding down the lock ring .

Release the lock ring of Di622 Mark II

when the mounting foot is fully slide into

the hotshoe of the camera.

Lock pin comes out to hook the foot at

the hotshoe for sure contact.

*For Nikon and Canon type digital SLR cameras

Mounting Di622 Mark II on the camera

*For Sony type digital SLR cameras

*Sony type hotshoe / Flash stand

Removing Di622 Mark II from the camera

Push down the lock ring and slide the mounting foot of Di866 Mark II

off the hotshoe of the camera. Make sure to slide off the mounting foot

and completely clear the lock pin off the hooking slot on the hotshoe.

Before mounting or removing Di622 Mark II into or from the camera,

make sure to turn off the power switch of both Di622 Mark II and the

camera.

NOTE

Produkt Specifikationer

Mærke:	Nissin
Kategori:	Blitz
Model:	Di622 Mark II

Har du brug for hjælp?

Hvis du har brug for hjælp til Nissin Di622 Mark II stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blitz Nissin Manualer

Nissin DI700A for Micro Four Thirds Manual

24 August 2024

Nissin Di866 Mark II Manual

19 August 2024

Nissin Di866 Professional Manual

15 August 2024

Nissin i600 Manual

15 August 2024

Nissin MG80 Manual

15 August 2024

Nissin Di700A Manual

15 August 2024

Nissin MF18 Macro Ring Manual

14 August 2024

Nissin I40 (Canon) Manual

14 August 2024

Nissin Di700 Nikon Manual

14 August 2024

Nissin i60A (Sony) Manual

13 August 2024

Blitz Manualer

Nyeste Blitz Manualer

Smith-Victor Orbit Pro Manual

24 Februar 2025

8 Januar 2025

8 Januar 2025

8 Januar 2025

8 Januar 2025

6 Januar 2025

Quantum Omicron 3 Manual

27 December 2024

Sony FDA-V1K Manual

22 December 2024

Sony FA-SHC1AM Manual

22 December 2024

Sony HVL-IRM Manual

22 December 2024