Novation Nova II Manual

Novation Ikke kategoriseret Nova II

Læs gratis den danske manual til Novation Nova II (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Novation Nova II, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
A Guide To Using The Supernova II Multitimbrally With A Sequencer
There is a template inside the Supernova - Performance A126 “Multi Ch 1 -8” which has been setup specially for easy multitimbral use.
This Performance has all available 8 Parts active, with Part 1 set to midi channel 1, Part 2 set to midi channel 2 ... Part 8 set to midi channel 8.
Performance A 126 should be selected when you wish to use more than 1 Part at a time on different midi channels.
The Supernova II needs to be set up to use this Performance effectively for the following reasons:
Attempting to assign a Program to a Part where the Part midi channel is identical to the Global Midi channel will result in the Supernova chang-
ing back into Program Mode. Hence It is important that the Global Midi channel inside the Supernova is changed from it’s default value of midi
channel 1 to any channel higher than channel 8 when using the Multitimbral Performance. Channels 9 and 16 are popular choices simply
because they are easy to remember.
When the Supernova II is used with a full midi loop such as with a sequencer, it is recommended that the Local Control is turned off. This will
ensure that the Supernova II does not recieve two messages corresponging to one change (ie a direct message from the front panel and one
via midi).
Performance A126 can be set to be the default patch the Supernova II shows when turned on. [the default patch is set when the Global Data is
written to memory].
Step By Step Operations:
1) select Performance A126 from the front panel of the Supernova.
2) Press the Global button to activate the global menu.
3) Page down to find the Global Miidi channel page. Set this to a channel greater than 8 (9 is used throughout this example).
4) Page up to find the page with Memory Protect and Local Control settings. Turn Memory Protect off.
5) Turn Local Control off.
6) Press the “write” button. The screen will show “save global set up with memory protect off?” You can change the default memory protect
status to “on” if you wish (the data encoder to the right of the screen toggles between on & off). Once the Memory Protect setting is set as
you wish press the “write” button once more.
7) Turn the Supernova off and then back on, notice that the Supernova now shows Performance A126 on the screen when it is first turned
on.
PLEASE NOTE: When the local control is turned off, the Supernova will not respond to it’s
own front panel or keyboard AT ALL. Instead, every single button press or control tweak
will transmit a corresponding midi message which must be routed back into the Supernova
on an appropriate midi channel.
To use the first Part in the Multitimbral Performance, highlight the track in the seuqencer corresponding to midi channel 1, press the Part 1 but-
ton on the Supernova and change the Program assigned to Part 1 as you wish.
To select a Program or Performance, play a Program in Program Mode or to adjust any Global setting (anything found in the Global Menu &
Master Volume), highlight the Global Track as above. This Global Track needs to be highlighted when Programs and Performances are written
to memory too.
To use Part three in the Multitimbral Performance, highlight the track corresponding to midi channel 3 and assign the Program you wish to Part
3. Now press the Part 3 button on the Supernova - the Program you selected will be shown as being assigned to part 3. ie the sequencer has
been used to route the information the Supernova transmitted to midi channel 3.
This procedure can be followed until all 8 parts have been assigned to the Supernova. ie highlight the corresponding part track and then
change the program assigned to the part.
For full control of the Supernova in Local Control “off” mode, 9 midi channels are needed in the Supernova and 9 tracks are needed in the
sequencer (as shown below.). There should be a sequencer track for each of the 8 Parts on midi channels 1 - 8 respectively and an additional
sequencer track for the Global Midi channel. Now when midi messages are sent from the Supernova to the sequencer, the sequencer will reroute
these messages according to which ever track is highlighted in the sequencer - ie you control which midi channel the Supernova receives midi
data on.
To route
midi data to
the
Supernova
on the glob-
al midi
channel,
highlight the
global midi
track in the
sequencer.
To route
midi data to
the
Supernova
on the part
1 midi chan-
nel, high-
light the
part 1 track
in the
sequencer.
To route
midi data to
the
Supernova
on the part 3
midi chan-
nel, highlight
the part 3
track in the
sequencer.

Produkt Specifikationer

Mærke: Novation
Kategori: Ikke kategoriseret
Model: Nova II

Har du brug for hjælp?

Hvis du har brug for hjælp til Novation Nova II stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Novation Manualer

Novation

Novation Nova Laptop Manual

12 September 2025
Novation

Novation ReMOTE 49 SL Compact Manual

12 September 2025
Novation

Novation ReMOTE 37 SL Manual

12 September 2025
Novation

Novation K-Station Manual

12 September 2025
Novation

Novation Xio 25 Manual

12 September 2025
Novation

Novation 49SL MkIII Manual

11 September 2025
Novation

Novation Twitch Manual

11 September 2025
Novation

Novation MoroderNova Manual

11 September 2025
Novation

Novation ReMOTE 61 SL Manual

11 September 2025
Novation

Novation FLkey 49 Manual

11 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM

IFM SU9030 Manual

13 September 2025
IFM

IFM O2U554 Manual

13 September 2025
Speco Technologies

Speco Technologies HTi70TM Manual

13 September 2025
QSC

QSC RMXa Manual

13 September 2025
Tineco

Tineco Floor One S2 Series Manual

13 September 2025
Tineco

Tineco Floor One S3 Breeze Manual

13 September 2025
Tineco

Tineco Floor One S5 Steam Manual

13 September 2025
Osram

Osram VX500-CB Manual

13 September 2025
Zelmer

Zelmer ZTS7990 Manual

13 September 2025
Osram

Osram VX250-SP Manual

13 September 2025