Ozito ACK-PRO Manual

Ozito Ikke kategoriseret ACK-PRO

Læs gratis den danske manual til Ozito ACK-PRO (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 45 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 23 anmeldelser. Har du et spørgsmål om Ozito ACK-PRO, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

DESCRIPTION OF SYMBOLS

GENERAL AIR TOOL SAFETY WARNINGS

SPARE PARTS

AIR

CHISEL

10.2mm Shank

INSTRUCTION MANUAL

SPECIFICATIONS

ACK-PRO

Max Air Pressure: 90psi (6Bar)

Av. Air Consumption: 113l/min (4cfm)

No Load Speed: 4,500 bpm

Chisel Shank (Round): 10.2mm (0.4”)

Barrel Stroke: 43mm

Air Inlet: 1/4“ BSP

Weight: 1.05kg

1 Quick Change Spring

2 On/Off Trigger

3 Air Inlet

4 Air Regulator

KNOW YOUR PRODUCT

Quick Change Spring SPACKPRO-07

Trigger SPACKPRO-08

Spare parts can be ordered from the Special Orders

Desk at your local Bunnings Warehouse.

For further information, or any parts not listed here, visit

www.ozito.com.au or contact Ozito Customer Service:

Australia 1800 069 486

New Zealand 0508 069 486

Email: enquiries@ozito.com.au

AIR CHISEL SAFETY WARNINGS

Warning Read instruction

manual

Wear eye protection

No load speed

Wear ear protection

Revolutions or

reciprocation per minute

/min no

WARNING! Use thick cushioned gloves and limit the exposure time by taking

frequent breaks.

• Vibration caused by the hammer action may be harmful to your hands and arms.

• When removing an accessory from the tool avoid contact with skin and use proper

protective gloves when grasping the bit or accessory. Accessories may be hot after

prolonged use.

• Always wear eye protection and a dust mask for dusty applications and when drilling/

chiselling overhead. Sanding particles can be absorbed by your eyes and inhaled easily

and may cause health complications.

WARNING! Read all safety warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference. The term “power tool” in the warnings

refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

a. Cluttered or dark areas invite accidents. Keep work area clean and well lit.

b. Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust

or fumes.

c. Distractions can Keep children and bystanders away while operating a power tool.

cause you to lose control.

d. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts. Loose clothes, jewellery or long hair can be

caught in moving parts.

e. Check the maximum pressure rating of any tools or accessories that you intend using with

the compressor. The output pressure of the air from the compressor must be regulated so

that it never exceeds the rated pressure of the tool or accessory.

f. Always wear safety goggles or glasses when using the air compressor. Never point the

nozzle of an accessory towards any part of your body or towards another person.

g. Drain the moisture from the tank daily. It will help prevent corrosion.

h. Use safety equipment including safety goggles or shield, ear protection, breathing respirator

mask and protective clothing.

i. Air tools should not be used in a potentialy explosive environment.

j. Use safety equipment including safety goggles or shield, ear protection, breathing or

respirator mask and protective clothing.

k. Any use other than those mentioned The tool must be used only for its prescribed purpose.

in this Manual will be considered a case of misuse. The user and not the manufacturer

shall be liable for any damage or injury resulting from such cases of misuse.

WARNING! In the event that an air line is cut or broken, the air supply must be turned off

at the compressor. A broken air line which is not supported is extremely dangerous and

can whip around very quickly, both with the capability of striking people, and blowing foreign

particles into the air.

Do not attempt to catch the air line but immediately keep bystanders well clear and turn off the air

supply to the hose, turn off the compressor at the On / Off button, and then remove the hose from

the compressor.

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they

have been given the supervision or instruction concerning use of the appliance by a person

responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

TROUBLESHOOTINGMAINTENANCE

If the air chisel fails to work eﬀecvely, perform the following

checks:

• Check the air regulator is not fully ghtened. Try selecng a higher

||seng.

• Check the air inlet is free of any dirt or blockages.

• Ensure the chisel is lubricated properly.

• Check that the pressure on the air compressor is within its

||working range. If not, let the compressor rest to

||re-pressurise / refer to the compressor instruction manual.

Note: This tool is rated at 90psi. Ensure your compressor is set no higher than 90psi.

• Keep the ventilation vents of the chisel clean at all times, if

possible, prevent foreign matter from entering the vents.

• If the enclosure of the chisel requires cleaning, do not use

solvents but a moist soft cloth only. Never let any liquid get inside

the chisel; never immerse any part of the chisel into a liquid.

• Oil the chisel after each use.

CONNECTING TO COMPRESSOR

OPERATION

ATTACHING TOOLS

3. Screw the male nio ﬁng

clockwise into the female end

of the air inlet.

4. Pull back the sleeve on hose

ﬁng, insert male end & release

sleeve on hose ﬁng.

1. Remove black plasc cap

from air inlet.

2. Wrap the threaded male

end with teﬂon tape in a

clockwise direcon.

2. To turn the chisel on, squeeze

the on/oﬀ trigger. To turn oﬀ,

release the on/oﬀ trigger.

1. Select the desired tool aachment

and lock into place using the quick

change spring.

2. Slide the aachment into the

hole while holding the quick change

spring back.

1. Screw the quick change spring onto

the housing.

3. To release the aachment pull

back the spring and then remove.

3. To restrict the air ﬂow turn the

regulator valve to a lower seng.

WARNING! Before attaching or removing any accessories, be sure to disconnect the air chisel from the air supply.

Alternavely, you can place the accessory into the housing and then screw in the quick change spring.

Produkt Specifikationer

Mærke:	Ozito
Kategori:	Ikke kategoriseret
Model:	ACK-PRO

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito ACK-PRO stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ozito Manualer

Ozito PXLMB-335 Manual

19 August 2025

Ozito PXCG-080 Manual

29 Juli 2025

Ozito PXGAR-500 Manual

29 Juli 2025

Ozito PXSK-2518 Manual

22 Juni 2025

Ozito PXBPS-1828 Manual

2 Juni 2025

Ozito PXLEK-1840 Manual

5 Januar 2025

Ozito PXBGSS-1815 Manual

10 December 2024

Ozito PXBSPS-180 Manual

6 Oktober 2024

Ozito SSH-240 Manual

6 Oktober 2024

Ozito DMC-1000 Manual

20 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Supermicro SuperStorage 6039P-E1CR16L Manual

3 Oktober 2025

Sony MRW-G3 Manual

3 Oktober 2025

GYS DIAG-BATIUM 100.12 FV Manual

3 Oktober 2025

Sony INZONE KBD-H75 Manual

3 Oktober 2025

3 Oktober 2025

3 Oktober 2025

3 Oktober 2025

2 Oktober 2025

Supermicro SuperStorage 6029P-E1CR12L Manual

2 Oktober 2025

Sony BKM-FW12 Manual

2 Oktober 2025