Ozito ACO-PRO Manual

Ozito Ikke kategoriseret ACO-PRO

Læs gratis den danske manual til Ozito ACO-PRO (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Ozito ACO-PRO, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
WARNING! Do not use accessories which are not specifically designed and
recommended by the tool manufacturer. Just because the accessory can be attached
to your power tool, it does not assure safe operation.
• The rated speed of the accessory must be at least equal to the maximum speed marked
on the power tool. Accessories running faster than their rated speed can break and fly apart.
• Wear personal protective equipment. Depending on application, use face shield, safety
goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and
workshop apron capable of stopping small abrasive or workpiece fragments. The eye
protection must be capable of stopping flying debris generated by various operations . The dust
mask or respirator must be capable of filtrating particles generated by your operation. Prolonged
exposure to high intensity noise may cause hearing loss.
• Never place your hand near the rotating accessory. Accessory may kickback over your
hand.
• Do not position your body in the area where power tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to the wheel’s movement at the point of
snagging.
DESCRIPTION OF SYMBOLS SPARE PARTS
AIR CUT-OFF
TOOL
76.2mm (3”)
INSTRUCTION MANUAL
SPECIFICATIONS
ACO-PRO
Max Air Pressure: 90psi (6Bar)
Av. Air Consumption: 170l/min (6cfm)
No Load Speed: 20,000/min
Wheel Diameter: 76.2mm (3”)
Air Inlet: 1/4“ BSP
Weight: 0.76kg
Guard Lock Nut SPACOPRO-28
3” Cutting Blade SPACOPRO-29
Blade Bolt & Washer SPACOPRO-30A
Spanner SPACOPRO-33
Spare parts can be ordered from the Special Orders Desk at
your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
Email: enquiries@ozito.com.au
Warning Read instruction
manual
Wear eye protection
No load speed
Wear ear protection
Revolutions or
reciprocation per minute
/min no
GENERAL AIR TOOL SAFETY WARNINGS
AIR CUT-OFF TOOL SAFETY WARNINGS
WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the warnings
refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Cluttered or dark areas invite accidents. Keep work area clean and well lit.
b. Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust
or fumes.
c. Distractions can Keep children and bystanders away while operating a power tool.
cause you to lose control.
d. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
e. Check the maximum pressure rating of any tools or accessories that you intend using with
the compressor. The output pressure of the air from the compressor must be regulated so
that it never exceeds the rated pressure of the tool or accessory.
f. Always wear safety goggles or glasses when using the air compressor. Never point the
nozzle of an accessory towards any part of your body or towards another person.
g. Drain the moisture from the tank daily. It will help prevent corrosion.
h. Use safety equipment including safety goggles or shield, ear protection, breathing respirator
mask and protective clothing.
i. Air tools should not be used in a potentialy explosive environment.
j. Use safety equipment including safety goggles or shield, ear protection, breathing or
respirator mask and protective clothing.
k. Any use other than those mentioned The tool must be used only for its prescribed purpose.
in this Manual will be considered a case of misuse. The user and not the manufacturer
shall be liable for any damage or injury resulting from such cases of misuse.
WARNING! In the event that an air line is cut or broken, the air supply must be turned off
at the compressor. A broken air line which is not supported is extremely dangerous and
can whip around very quickly, both with the capability of striking people, and blowing foreign
particles into the air.
Do not attempt to catch the air line but immediately keep bystanders well clear and turn off the air
supply to the hose, turn off the compressor at the On / Off button, and then remove the hose from
the compressor.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given the supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
• Such blades create Do not attach a saw chain woodcarving blade or toothed saw blade.
frequent kickback and loss of control.
• Use special care when working corners, sharp edges etc. Avoid bouncing and
snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the
rotating accessory and cause loss of control or kickback.
• Wheels must be used only for recommended applications. For example: do not grind
with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side
forces applied to these wheels may cause them to shatter.
• Always use undamaged wheel flanges that are of correct size and shape for your
selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel
breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.
• Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to make an
excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to
twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.
• Do not restart the cutting operation in the workpiece. Let the wheel reach full speed
and carefully re-enter the cut. The wheel may bind, walk up or kickback if the power tool is
restarted in the workpiece.
KNOW YOUR PRODUCT
1 Cutting Disc
2 Guard
3 Spindle
4 Lock-off Lever
5 On/Off Trigger
6 Air Inlet
TROUBLESHOOTING
MAINTENANCE
If the air cut-off tool fails to work effecvely, perform the
following checks:
• Check the air inlet is free of any dirt or blockages.
• Ensure the tool is lubricated properly.
• Check that the pressure on the air compressor is within its
||working range. If not, let the compressor rest to
||re-pressurise / refer to the compressor instruction manual.
• Keep the ventilation vents of the cut-off tool clean at all times,
if possible, prevent foreign matter from entering the vents.
• If the enclosure of the tool requires cleaning, do not use
solvents but a moist soft cloth only. Never let any liquid get inside
the tool; never immerse any part of the cut-off tool into a liquid.
• Oil the cut-off tool after each use.
CONNECTING TO COMPRESSOR
OPERATION
ATTACHING TOOLS
3. Screw the male nio fing
clockwise into the air inlet.
4. Pull back the sleeve on hose
fing, insert male end & release
sleeve on hose fing.
1. Remove black plasc cap
from the air inlet.
2. Wrap the threaded male
end with teflon tape in a
clockwise direcon.
3. Place washer and blade bolt
onto the spindle.
4. Tighten the blade bolt using the
provided hex key and spanner in
opposite direcons.
1. Undo the spindle using
the provided hex key and
spanner turning in
opposite direcons.
2. Place the cung disc onto
the spindle with the metal
ring facing down.
2. To turn the tool on squeeze the
on/off trigger.
1. Push and hold the lock-off lever
forward.
3. To turn off, release the on/off
trigger.
Note: Disconnect the tool from the air supply before performing the below operaons.
Note: This tool is rated at 90psi. Ensure your compressor is set no higher than 90psi.

Produkt Specifikationer

Mærke: Ozito
Kategori: Ikke kategoriseret
Model: ACO-PRO

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito ACO-PRO stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Ozito Manualer

Ozito

Ozito PXLMB-335 Manual

19 August 2025
Ozito

Ozito PXCG-080 Manual

29 Juli 2025
Ozito

Ozito PXGAR-500 Manual

29 Juli 2025
Ozito

Ozito PXSK-2518 Manual

22 Juni 2025
Ozito

Ozito PXBPS-1828 Manual

2 Juni 2025
Ozito

Ozito PXLEK-1840 Manual

5 Januar 2025
Ozito

Ozito PXBGSS-1815 Manual

10 December 2024
Ozito

Ozito PXBSPS-180 Manual

6 Oktober 2024
Ozito

Ozito SSH-240 Manual

6 Oktober 2024
Ozito

Ozito DMC-1000 Manual

20 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Sony

Sony AIBO ERS-7M2 Manual

3 Oktober 2025
AFK

AFK EWK-2200.73C Manual

3 Oktober 2025
TOA

TOA TS-D1000-DU Manual

3 Oktober 2025
Zoom

Zoom G1M Manual

3 Oktober 2025
Arris

Arris Touchstone TM902 Manual

3 Oktober 2025
Inkbird

Inkbird PTH-10C Manual

3 Oktober 2025
Rowenta

Rowenta Professional DW8115 Manual

3 Oktober 2025
AFK

AFK EWK-2200.5 Manual

3 Oktober 2025
Realme

Realme GT3 Manual

3 Oktober 2025
Supermicro

Supermicro SuperServer SYS-110D-4C-FRAN8TP Manual

3 Oktober 2025