Ozito PLHA-001 Manual

Ozito Ikke kategoriseret PLHA-001

Læs gratis den danske manual til Ozito PLHA-001 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 44 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 22.5 anmeldelser. Har du et spørgsmål om Ozito PLHA-001, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

CHAINSAW

CUTTING STAND

Ø250mm

INSTRUCTION MANUAL

SPECIFICATIONS

Working Heights: 3 (600, 640, 680mm)

Length: 800mm approx.

Logs: 250mm approx.Ø

Load Capacity: 150kg

Weight: 7.3kg

PLHA-001

STANDARD EQUIPMENT

3 YEAR REPLACEMENT WARRANTY*

Your product is guaranteed for a period of If 36 months from the original date of purchase.

a product is defective it will be replaced in accordance with the terms of this warranty. Warranty

excludes consumable parts, for example: valve adapters and accessories.

*This product is intended for DIY use only and replacement warranty covers domestic use.

WARNING

The following actions will result in the warranty being void.

• If the tool has been operated on a supply voltage other than that speciﬁed on the tool.

• If the tool shows signs of damage or defects caused by or resulting from abuse, accidents

or alterations.

• Failure to perform maintenance as set out within the instruction manual.

• If the tool is disassembled or tampered with in any way.

• Professional, industrial or high frequency use.

WARRANTY

OZITO Australia/New Zealand (Head Ofﬁce) 25 Fox Drive, Dandenong South, Victoria, Australia 3175.

ozito.com.au

2 x Legs A, B, & C

2 x Cross Struts D & E

1220

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY

YOU MUST RETURN THE PRODUCT TO YOUR NEAREST

BUNNINGS WAREHOUSE WITH YOUR BUNNINGS

PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR

CUSTOMER SERVICE HELPLINE:

Australia: 1800 069 486

New Zealand: 0508 069 486

The beneﬁts provided under this warranty are in addition to other rights and remedies which

are available to you at law.

Our goods come with guarantees that cannot be excluded at law. You are entitled to a

replacement or refund for a major failure and for compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the

goods fail to be of acceptable quality and the failure does not amount to a major failure.

Generally you will be responsible for all costs associated with a claim under this warranty,

however, where you have suffered any additional direct loss as a result of a defective product

you may be able to claim such expenses by contacting our customer service helpline above.

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE

THE MODEL NUMBER AND DATE OF PURCHASE

AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE

WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS

YOU MAY HAVE RELATING TO THE WARRANTY POLICY

OR PROCEDURE.

3 x F Bolt & Nut M8x14

2 x G Screw & Nut M6x28

8 x H Screw & Nut M6x12

2 x I Screw, Nut & Washer M6x12

1. ASSEMBLY

SETUP & PREPARATION

WARNING! WEAR SAFETY GLOVES - TAKE CARE THAT

YOU DO NOT INJURE YOURSELF ON SHARP CORNERS

OR EDGES.

KNOW YOUR PRODUCT

ONLINE MANUAL

Scan this QR Code with your mobile

device to take you to the online manual.

A. Leg A x 2

B. Leg B x 2

C. Leg C x 2

D. Cross Strut D x 2

E. Cross Strut E x 2

CHAINSAW CUTTING STAND

F G

B A

F. M8x14 Bolt & Nut x 3

G. M6x28 Screw & Nut x 2

H. M6x12 Screw & Nut x 8

I. M6x12 Screw, Nut & Washer x 3

J. Safety Catch

Assembly of the Stand

The legs are constructed by assembling each half of the structure

and then joining them together.

Tools for assembly (not included): Phillips screwdriver, M10, M13 &

M14 spanners.

1. Lay three legs on the ground, parallel to each other with teeth

facing up.

2. Place cross strut E over each leg, aligning the holes with the

lower holes on each leg.

Note: Leg C is positioned off centre to the left, this will allow

correct alignment with the second half when joining them together.

BA C

3. Lay cross strut D over E and all

three legs.

4. Once aligned, insert G screw

from the outside and tighten nut

on the inside (only hand tight at

this initial stage).

5. Using H screw and nut loosely

fastening the remaining legs and

cross struts together.

6. Once all the legs and cross struts are joined together and the

fasteners are assembled, use a spanner and screwdriver to

tension the fasteners to complete this half of the structure.

Produkt Specifikationer

Mærke:	Ozito
Kategori:	Ikke kategoriseret
Model:	PLHA-001

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito PLHA-001 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ozito Manualer

Ozito PXLMB-335 Manual

19 August 2025

Ozito PXCG-080 Manual

29 Juli 2025

Ozito PXGAR-500 Manual

29 Juli 2025

Ozito PXSK-2518 Manual

22 Juni 2025

Ozito PXBPS-1828 Manual

2 Juni 2025

Ozito PXLEK-1840 Manual

5 Januar 2025

Ozito PXBGSS-1815 Manual

10 December 2024

Ozito PXBSPS-180 Manual

6 Oktober 2024

Ozito SSH-240 Manual

6 Oktober 2024

Ozito DMC-1000 Manual

20 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Supermicro SuperStorage 6039P-E1CR16L Manual

3 Oktober 2025

Sony MRW-G3 Manual

3 Oktober 2025

GYS DIAG-BATIUM 100.12 FV Manual

3 Oktober 2025

Sony INZONE KBD-H75 Manual

3 Oktober 2025

3 Oktober 2025

3 Oktober 2025

3 Oktober 2025

2 Oktober 2025

Supermicro SuperStorage 6029P-E1CR12L Manual

2 Oktober 2025

Sony BKM-FW12 Manual

2 Oktober 2025