Ozito PXSMSK-800MS Manual

Ozito Ikke kategoriseret PXSMSK-800MS

Læs gratis den danske manual til Ozito PXSMSK-800MS (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Ozito PXSMSK-800MS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

STANDARD EQUIPMENT

PXSMSK-800MS

INSTRUCTION MANUAL

SPECIFICATIONS

Folded Size: 940 x 545 x 810mm

Length: 940mm (Folded)

1950mm (Extended)

Height: 810mm (Folded)

920mm (Extended)

Loading Capacity: 150kg

Weight: 9.65kg

ozito.com.au

0223

Mitre Saw Stand

2 x Roller Arms, 2 x Mounting

Bars, 2 x Extension Arms

4 x 60mm bolts, 4 x 35mm

bolts, 4 x Washers, 4 x Spring

Washers, 4 x Hex Nuts

4 x Fastening Knobs

MITRE SAW

STAND

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU

MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS

WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO

RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE

OUR CUSTOMER SERVICE HELPLINE:

Australia 1800 069 486

New Zealand 0508 069 486

WARRANTY

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL

NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER

SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND

ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE

WARRANTY POLICY OR PROCEDURE.

OZITO INDUSTRIES PTY. LTD. 25 Fox Drive, Dandenong South, VIC 3175, Australia.

The benets provided under this warranty are in addition to other rights and

remedies which are available to you at law.

Our goods come with guarantees that cannot be excluded at law. You are entitled to

a replacement or refund for a major failure and for compensation for any other

reasonably foreseeable loss or damage. You are also entitled to have the goods

repaired or replaced if the goods fail to be of acceptable quality and the failure

does not amount to a major failure.

Generally you will be responsible for all costs associated with a claim under this

warranty, however, where you have suffered any additional direct loss as a result of

a defective product you may be able to claim such expenses by contacting our

customer service helpline above.

WARNING

The following actions will result in the warranty being

void.

• If the tool has been operated on a supply voltage other than that specied

on the tool.

• If the tool shows signs of damage or defects caused by or resulting from

abuse, accidents or alterations.

• Failure to perform maintenance as set out within the instruction manual.

• If the tool is disassembled or tampered with in any way.

5 YEAR REPLACEMENT WARRANTY

Your Product is guaranteed for a period of 60 months from the original date of

purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it

will be replaced in accordance with the terms of this warranty. Lithium Ion

batteries and chargers are covered by a 36 month

warranty and are excluded from the warranty extension. Warranty excludes

consumable parts.

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to

the online manual.

Unfolding The Stand

1. Lay the mitre saw stand on the

oor with the folded legs facing

up.

2. Depress the leg locking button

and unfold the 2 upper legs until

the locking button clicks into

place.

3. Repeat the same procedure for the other 2 legs.

4. Lift the stand and ip it into the upright position.

5. Check that the stand is stable

and all of the leg locking buttons

have engaged properly.

Folding The Stand

1 pair of legs on the stand must fold in rst for the stand to fold at. The

legs have not folded into place if the leg locking button does not pop into

place. The legs should not swing about when the stand is picked up if the

legs have locked into position.

1. Turn the mitre saw upside down on the oor with the legs sticking up.

2. Depress the leg locking buttons on the lower pair of legs and fold them

in.

3. Repeat the same procedure on

the other pair of legs.

1. Mounting Bar

2. Fastening Slot

3. Mounting Bar Handle

4. Extension Arm Locking Pin

5. Roller

6. Material Support ShelfRed

MITRE SAW STAND

KNOW YOUR PRODUCT

1. ASSEMBLY

SETUP & PREPARATION

3 4 5

WARNING! THIS STAND IS INTENDED FOR USE WITH

MITRE SAWS ONLY. DO NOT USE A STEP LADDER,

STEPPING STOOL, STORAGE RACK, ETC.

OZITO WILL NOT BE LIABLE FOR DAMAGE OR INJURY

CAUSED BY IMPROPER USE OF THIS UNIT.

7. Upper Leg Locking Pin

8. Stand Leg

9. Frame

10. Extension Arm Fastening Knob

11. Lower Leg Locking Pin

12. Extension Arm

13. Roller Arm

14. Roller Arm Fastening Knob

Produkt Specifikationer

Mærke:	Ozito
Kategori:	Ikke kategoriseret
Model:	PXSMSK-800MS

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito PXSMSK-800MS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ozito Manualer

Ozito PXCG-080 Manual

29 Juli 2025

Ozito PXGAR-500 Manual

29 Juli 2025

Ozito PXSK-2518 Manual

22 Juni 2025

Ozito PXBPS-1828 Manual

2 Juni 2025

Ozito PXLEK-1840 Manual

5 Januar 2025

Ozito PXBGSS-1815 Manual

10 December 2024

Ozito PXBSPS-180 Manual

6 Oktober 2024

Ozito SSH-240 Manual

6 Oktober 2024

Ozito DMC-1000 Manual

20 September 2024

Ozito PXBCSS-184 Manual

15 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kenmore SM2050 Manual

17 August 2025

Vulcan VBB1CF Manual

17 August 2025

MSW -WPD-PVDC4/2 Manual

17 August 2025

Kenmore DU1275 Manual

17 August 2025

YA-MAN Bloom 5 Manual

17 August 2025

OSD Audio NERO-CONTROL12 Manual

17 August 2025

Singercon SIN-ALD-2000 Manual

17 August 2025

Vulcan VIB2 Manual

17 August 2025

Mars Gaming MNBC5 Manual

17 August 2025

Mars Gaming MNBC6 Manual

17 August 2025