Ozito PXSMSS-036 Manual

Ozito Ikke kategoriseret PXSMSS-036

Læs gratis den danske manual til Ozito PXSMSS-036 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Ozito PXSMSS-036, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

STANDARD EQUIPMENT

PXSMSS-036

INSTRUCTION MANUAL

SPECIFICATIONS

Input: 2 x 18V

No Load Speed: 3,800/min

Blade: Ø210 x Ø30 x 1.8mm (40T)

Mitre Angle: 0-45° Left & Right

Bevel Angle: 0-45° Left

Cutting Capacity:

Mitre 0° x Bevel 0°: 65 x 310mm

Mitre 45° x Bevel 0°: 65 x 210mm

Mitre 0° x Bevel 45°: 35 x 310mm

Mitre 45° x Bevel 45°: 35 x 210mm;

Weight: 12.5kg

ozito.com.au

0922

Ø210mm Sliding Compound

Mitre Saw

2 x Extension Tables, Table

Handle & Carry Handle

Dust Bag, Material Clamp &

Combination Key

Ø210MM SLIDING

COMPOUND

MITRE SAW

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU

MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS

WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO

RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE

OUR CUSTOMER SERVICE HELPLINE:

Australia 1800 069 486

New Zealand 0508 069 486

WARRANTY

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL

NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER

SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND

ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE

WARRANTY POLICY OR PROCEDURE.

OZITO INDUSTRIES PTY. LTD. 25 Fox Drive, Dandenong South, Victoria, Australia 3175.

The benets provided under this warranty are in addition to other rights and

remedies which are available to you at law.

Our goods come with guarantees that cannot be excluded at law. You are entitled to

a replacement or refund for a major failure and for compensation for any other

reasonably foreseeable loss or damage. You are also entitled to have the goods

repaired or replaced if the goods fail to be of acceptable quality and the failure

does not amount to a major failure.

Generally you will be responsible for all costs associated with a claim under this

warranty, however, where you have suffered any additional direct loss as a result of

a defective product you may be able to claim such expenses by contacting our

customer service helpline above.

WARNING

The following actions will result in the warranty being

void.

• If the tool has been operated on a supply voltage other than that specied

on the tool.

• If the tool shows signs of damage or defects caused by or resulting from

abuse, accidents or alterations.

• Failure to perform maintenance as set out within the instruction manual.

• If the tool is disassembled or tampered with in any way.

5 YEAR REPLACEMENT WARRANTY

Your Product is guaranteed for a period of 60 months from the original date of

purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it

will be replaced in accordance with the terms of this warranty. Lithium Ion

batteries and chargers are covered by a 36 month

warranty and are excluded from the warranty extension. Warranty excludes

consumable parts.

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to

the online manual.

O F F

This tool is compatible with all batteries & chargers from the Ozito PXC range.

For optimal performance, we recommend the use of a 3.0Ah batteries or higher to

operate this PXC Mitre Saw.

CORDLESS SLIDING MITRE SAW

BATTERY & CHARGER

KNOW YOUR PRODUCT

1. ASSEMBLY

SETUP & PREPARATION

Note: The combination key is located inside the slot on the slide bar

at the back of the unit, and can be used for assembly. Make sure the

correct extension table is used for left & right sides respectively. Ensure

the extension tables are installed correctly, and always use the extension

tables during operation.

1. Remove the screw from the bar of the extension table.

2. Press and hold the lever located

inside the extension table handle

and slide the bars into the slots on

the unit. The notched bar should be

inserted through the bracket on the

underside of the unit.

3. Replace and tighten the screw.

4. Repeat steps 1, 2 & 3 for the other extension table.

5. Align the table handle with the bar on the

mitre table and screw it into place.

6. Press the end cap into the table handle.

7. Remove the screws on the top of the unit.

8. Align the holes in the carry handle

with the screw holes and then

replace the screws to attach the

carry handle.

9. Squeeze the clamp at the end of the

dust bag and place it over the dust

extraction port.

Note: The dust extraction port can block easily

with dust and requires to be periodically cleaned.

For more efcient operation, empty the

dust bag when it is no more than half full.

This allows better air ow through the bag.

Dust bags will not collect all the saw dust

generated by the mitre saw. For best results

a dust extractor should be used in place of

the dust bag.

9. Hold down the cutting head and pull the lock down pin to release the

cutting head from its transport position.

HOLD

DOWN

WARNING! ENSURE THE TOOL IS TURNED OFF

AND DISCONNECTED FROM THE POWER SUPPLY

BEFORE PERFORMING ANY OF THE FOLLOWING

OPERATIONS.

1716 18 19

1. Battery Seating

2. Laser On/Off Switch

3. Lock-Off Lever

4. Spindle Lock Button

5. Lock Down Pin

6. Material Clamp

7. Fence

8. Table Insert

9. Table Lock

10. Table Handle

11. Mitre Angle Pointer

12. Mitre Table

13. Worklight & Laser

14. On/Off Trigger

15. Worklight On/Off Switch

16. Combination Key Storage

17. Slide Lock

18. Dust Bag

19. Slide Bar

20. Carry Handle

21. Cutting Handle

22. Saw Blade

23. Trenching Depth Screw

24. Retractable Blade Guard

25. Mounting Point

26. Extension Table Handle

27. Material Stop

28. Bevel lock

Produkt Specifikationer

Mærke:	Ozito
Kategori:	Ikke kategoriseret
Model:	PXSMSS-036

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito PXSMSS-036 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ozito Manualer

Ozito PXLMB-335 Manual

19 August 2025

Ozito PXCG-080 Manual

29 Juli 2025

Ozito PXGAR-500 Manual

29 Juli 2025

Ozito PXSK-2518 Manual

22 Juni 2025

Ozito PXBPS-1828 Manual

2 Juni 2025

Ozito PXLEK-1840 Manual

5 Januar 2025

Ozito PXBGSS-1815 Manual

10 December 2024

Ozito PXBSPS-180 Manual

6 Oktober 2024

Ozito SSH-240 Manual

6 Oktober 2024

Ozito DMC-1000 Manual

20 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hamilton Buhl Amp-Up Mini PA-25E Manual

4 Oktober 2025

Falmec Brooklyn Manual

4 Oktober 2025

Tempo 915CL Manual

4 Oktober 2025

StarTech.com F35023-USB-EXTENDER Manual

4 Oktober 2025

EasyMaxx 04670 Manual

4 Oktober 2025

LC-Power Arkangel 3 LC8850III V2.3 Manual

4 Oktober 2025

Falmec Brera 75 Manual

4 Oktober 2025

Kenwood Mesmerine TFM810 Manual

4 Oktober 2025

AFK EWK-2200.7C Manual

4 Oktober 2025

Realme Narzo 60x Manual

4 Oktober 2025