Ozito TBS-2010 Manual

Ozito Ikke kategoriseret TBS-2010

Læs gratis den danske manual til Ozito TBS-2010 (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 45 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 23 anmeldelser. Har du et spørgsmål om Ozito TBS-2010, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

ONLINE MANUAL

Scan this QR Code with your mobile

device to take you to the online manual.

T BS- 2010

Made in China

FO R TIM BER ONLY

(Diameter) Ø254 x (Bore) Ø30 x (Kerf) 2.4mm

FOR USE WITH TABLE SAWS O NLY

TIMB ER SAW B LADE

TUNGSTEN

CARBIDE

TEET H

(10”)

254

MAX S PEE D

7,000/MIN

WARNI N G !

• Do not us e this tungsten carbide tipped blade for mas onr y or metal cutting applications.

• Always us e s harp blades . Always ins pect blades for any da mage & cra cks .

• Refer to the power tool m anual for s afety warnings , blade m ounting & ope rating instructions .

• Always wear ey e, ear & res piratory protection. Always wear gloves .

2000W

TABLE

SAW

TABLE SAW

2000W

TABLE SAW

WITH STAND

2000W

ASSEMBLY MANUAL

0522

1. Table Saw

2. 254mm Saw Blade

3. Riving Knife

4. Sliding Mitre Gauge

5. Small Hex Nuts

6. Small Hex Bolt

7. 4 x Frame Legs

8. 4 x Cross Braces

9. 4 x Table Cross Braces

10. 20 x Nuts

11. 10 / 21mm Spanner

12. 10 / 13mm Spanner

13. 36 x Bolts

14. 4 x Foot Caps

15. 2 x Bracing Brackets

16. 2 x Short Table Struts

17. 2 x Long Table Struts

18. 2 x Table Extensions

19. Push Stick

20. Rip Fence

21. Blade Guard

STANDARD EQUIPMENT

1. Ensure the blade height is

wound fully down and then

turn the table saw upside

down on the ﬂoor.

2. Remove any cardboard boxes from

behind the motor; it can be easily

accessed by tilting the blade using

the bevel adjustment dial.

3. Align a table leg with the bolt

holes on the table saw and

attach it loosely with 2 of

the bolts. Repeat this for the

other 3 legs.

Note: Some of these bolts will

need to be removed later, so

only attach loosely.

4. Place the ﬂat side of a cross

brace against the inside face

between 2 legs. Use 4 bolts

and nuts to secure the brace

in place. Repeat the same

procedure for the other 3

cross braces.

Note: Only fully tighten the bolts and nuts once the machine has

been fully assembled, ﬂipped onto its feet and placed on a level

surface to ensure the frame is level.

5. Fit the rubber foot caps onto the

ends of the legs.

6. Use 2 bolts and nuts to

attach a bracing bracket to

one of the rear legs. Repeat

for the other bracing bracket

and rear leg.

7. To assemble the push stick

holder, screw one of the

small nuts onto the small

hex bolt.

8. Place this through one of the

holes on either of the front

legs and use the other small

nut to secure this in place.

Note: Unwind the hex bolt slightly if there is not enough space for

the push stick to hand securely.

1. ASSEMBLING THE FRAME

2000W

TABLE

SAW

200

TABLE

SAW

2000W

TABLE

SAW

2000W

TABLE

SAW

WARNING! ENSURE THE TOOL IS TURNED OFF AND

DISCONNECTED FROM THE POWER SUPPLY BEFORE

PERFORMING ANY OF THE FOLLOWING OPERATIONS.

TBS-2010

1. Use a Philips head

screwdriver (not supplied) to

loosen and remove the table

insert.

2. Remove the blade bolt. Use 21mm

and 13mm spanners to loosen it if

necessary.

3. Remove the outer ﬂange.

4. Thread the saw

blade onto the

axle and then

replace the

outer ﬂange and

bolt.

Note: Ensure the rotation arrows on the blade matches the

direction of the guide arrows in the blade cavity.

Note: Ensure that the inner ﬂange is attached to the motor shaft.

5. Use the 21mm spanner to

hold the axle while using the

13mm spanner to tighten

the bolt.

6. Use the 13mm spanner to loosen the

riving knife plate.

7. Slot the riving knife behind

the plate, leaving a 3-8mm

gap between the riving knife

and blade teeth.

8. Retighten the bolt to secure

the riving knife in place.

9. Replace the table insert by

sliding the back end in ﬁrst

under the lip of the blade

cavity, then redoing the

Philips head screw.

10. Slide the blade guard over

the riving knife, aligning

the bolt with the hole in the

riving knife. Turn the bolt

clockwise to lock it in place.

WARNING! THE BLADE GUARD MUST ALWAYS BE

LOWERED OVER THE WORKPIECE BEFORE BEGINNING

TO CUT.

1. With the table saw still

upside down on a ﬂat

surface, align a table

extension with the side of the

table saw.

2. Place a cross brace on the

extension piece and align

it with the bolt holes in the

table extension.

3. Use a bolt to secure the table

extension and table cross

brace to the table saw.

4. Repeat steps 2 and 3 for the other cross brace and then attach

the other table extension in the exact same manner.

5. Use another bolt to attach a

table strut to the outside of

the table extension. Repeat

for the other 3 table struts.

Note: One pair of table struts

is longer than the other. The

longer pair of table struts

should be used on the side of

the table saw with the power cord.

6. Undo the bolt on the table leg

side and use this to secure a

table strut against the table

leg & saw. Repeat for the

other 3 table struts.

7. Flip the table saw onto its feet and tighten up all of the bolts.

3. FITTING THE BLADE ASSEMBLY2. ATTACHING THE TABLE EXTENSIONS

BLADE

BOLT

OUTER

FLANGE

BLADE

TABL E SAW

2000W

3 - 8mm

2000W

TABLE

SAW

FRONT SIDE

Produkt Specifikationer

Mærke:	Ozito
Kategori:	Ikke kategoriseret
Model:	TBS-2010

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito TBS-2010 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ozito Manualer

Ozito PXLMB-335 Manual

19 August 2025

Ozito PXCG-080 Manual

29 Juli 2025

Ozito PXGAR-500 Manual

29 Juli 2025

Ozito PXSK-2518 Manual

22 Juni 2025

Ozito PXBPS-1828 Manual

2 Juni 2025

Ozito PXLEK-1840 Manual

5 Januar 2025

Ozito PXBGSS-1815 Manual

10 December 2024

Ozito PXBSPS-180 Manual

6 Oktober 2024

Ozito SSH-240 Manual

6 Oktober 2024

Ozito DMC-1000 Manual

20 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

StarTech.com RKUNITAPE Manual

3 Oktober 2025

Kenwood Abbey Lux TCP05 Manual

3 Oktober 2025

Realme 11x 5G Manual

3 Oktober 2025

Realme GT5 Manual

3 Oktober 2025

Sony PFM-510A2WU Manual

3 Oktober 2025

Arctic AATA-5G Manual

3 Oktober 2025

Fisher & Paykel WB30SPEX3 Manual

3 Oktober 2025

EasyMaxx 00621 Manual

3 Oktober 2025

Inkbird IBS-TH5-WiFi Manual

3 Oktober 2025

Sony EP-NI1010L Manual

3 Oktober 2025