Ozito ZLBP-015 Manual

Ozito Ikke kategoriseret ZLBP-015

Læs gratis den danske manual til Ozito ZLBP-015 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Ozito ZLBP-015, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

BATTERY SAFETY WARNINGS

ELECTRICAL SAFETY

CARING FOR THE ENVIRONMENT

Power tools that are no longer usable should not be disposed of

with household waste but in an environmentally friendly way. Please

recycle where facilities exist. Check with your local council authority

for recycling advice.

Recycling packaging reduces the need for landll and raw materials.

Reuse of recycled material decreases pollution in the environment.

Please recycle packaging where facilities exist. Check with your

local council authority for recycling advice.

DESCRIPTION OF SYMBOLS

Warning

Do not use or store battery in

temperatures exceeding 50ºC

Volts Hertz

Alternating Current

Direct Current

Milliamperes

Watts

Amp Hour

HzV

ac/~

Lithium Ion Battery

Do not put in the rubbish

Do not get battery wet

Recycle Battery

Do not incinerate

ZLBP-015

1.5Ah BATTERY

12V Lithium Ion

INSTRUCTION MANUAL

SPECIFICATIONS

Input: 12V

Battery Capacity: 1.5Ah Li-Ion

Charge Times: 1hr (Fast Charger)

3-5hrs (Eco Charger)

ozito.com.au

1 2

1 Battery Release Button

2 Battery

THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR

YOUR BATTERY CHARGER.

1. Before using the charger read all instructions and cautionary markings on the charger,

battery pack and the product using the battery pack.

2. This charger is not intended for any uses other than charging rechargeable batteries. Any

other use may result in risk of re, electric shock or electrocution.

3. Do not place any object on top of the charger or place the charger on a soft surface that

may result in excessive internal heat. Place the charger in a position away from any heat

source.

4. To reduce risk of damage to the electric plug and cord, pull by the plug rather than the

cord when disconnecting the charger.

5. Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

6. An extension cord should not be used unless absolutely necessary. Use of an improper

extension cord could result in the risk of re, electric shock or electrocution.

7. Do not operate the charger if it has received a sharp blow, been dropped or otherwise

damaged in any way. Have it checked by an electrician or power tool repairer.

8. Do not disassemble charger. Take it to an electrician or power tool repairer when

service or repair is required. Incorrect reassembly may result in a risk of electric shock,

electrocution or re.

9. To reduce risk of electric shock, unplug the charger from the outlet before attempting any

cleaning. Removing the battery pack will not reduce this risk.

10. Never attempt to connect 2 chargers together.

11. DO NOT store or use the tool and battery pack in locations where the temperature may reach

or exceed 40ºC (such as inside sheds or metal buildings in summer).

12. The charger is designed to operate on standard household electrical power (240 volts).

Do not attempt to use it on any other voltage!

13. The battery pack is not fully charged out of the carton. First read the safety instructions

and then follow the charging notes and procedures.

14. The longest life and best performance can be obtained if the battery pack is charged

when the air temperature is between 18 - 24ºC. Do not charge the battery pack in an air

temperature below 10ºC or above 40ºC. This is important and will prevent damage to the

battery pack.

15. Do not incinerate the battery pack even if it is seriously damaged or is completely worn out.

The battery can explode in a re.

16. Never attempt to open the battery pack for any reason. If the plastic housing of the battery

pack breaks or cracks, immediately discontinue use and do not recharge.

17. During charging, the battery must be placed in a well ventilated area.

WARNING! When using mains-powered tools, basic safety precautions,

including the following, should always be followed to reduce risk of re, electric

shock, personal injury and material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an

emergency, before operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

The electric motor has been designed for 230V and 240V only. Always check that the power

supply corresponds to the voltage on the rating plate.

Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New

Zealand.

This tools charger is double insulated therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in

order to avoid a hazard.

Note: Double insulation does not take the place of normal safety precautions when operating

this tool. The insulation system is for added protection against injury resulting from a possible

electrical insulation failure within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool. Before use,

inspect the extension lead for signs of damage, wear and ageing. Replace the extension lead if

damaged or defective.

When using an extension lead on a reel, always unwind the lead completely. Use of an

extension lead not suitable for the power input of the tool or which is damaged or defective may

result in a risk of re and electric shock.

BATTERY PROTECTION SYSTEM

The tool is equipped with a battery protection system, which helps to

ensure longevity of the battery.

The output power automatically cuts off during operation when the tool

and/or battery are placed under the following situations:

• When the tool is overloaded:

If this occurs, release the trigger switch and remove causes of

overload, then pull the switch trigger again to restart.

• When the remaining battery capacity becomes low:

Recharge the battery pack.

Note: The battery protection system does not in any way damage the

tool.

Note: The indicated capacity may be lower than the actual level during

use or immediately after using the tool.

ZLBP-015

CHARGING YOUR LITHIUM ION BATTERY

This battery has been shipped in a low charge condition, and requires

charging prior to use. Allow several cycles of charging and discharging

(through use with a compatible tool) for the battery to reach its optimum

performance / runtime.

This battery has two compatible Ozito chargers available through your

local Bunnings Warehouse:

• ZLCG-112 Fast Charger

• ZLCG-312 Eco Charger

Only use the battery pack with Ozito Home 12Volt cordless

products.

1. Insert the power plug of the charger into the mains socket outlet.

The red LED on the plug will begin to illuminate when properly

connected to power supply.

2. Insert the battery pack into the battery charger .

3. Remove battery from the charger once fully charged. Disconnect

the charger from the power supply.

Note: The battery pack can become a little warm during the charging.

This is normal

If the battery pack fails to charge, check:

• if there is voltage at the socket outlet

• that the battery and charger are properly connected.

If the battery pack still fails to charge, please contact our customer

service center.

1. OPERATION

IN ORDER TO MAKE A CLAIM UNDER THIS

WARRANTY YOU MUST RETURN THE PRODUCT

TO YOUR NEAREST BUNNINGS WAREHOUSE

WITH YOUR BUNNINGS REGISTER RECEIPT.

PRIOR TO RETURNING YOUR PRODUCT

FOR WARRANTY PLEASE TELEPHONE OUR

CUSTOMER SERVICE HELPLINE:

Australia 1800 069 486

New Zealand 0508 069 486

1 YEAR REPLACEMENT WARRANTY

Your product is guaranteed for a period of 12 months from the

original date of purchase and is intended for DIY (Do It Yourself) use

only. If a product is defective it will be replaced in accordance with the

terms of this warranty. Warranty excludes consumable parts.

WARNING

The following actions will result in the warranty being void.

• If the tool has been operated on a supply voltage other than that

speciﬁed on the tool.

• If the tool shows signs of damage or defects caused by or

resulting from abuse, accidents or alterations.

• Failure to perform maintenance as set out within the instruction

manual.

• If the tool is disassembled or tampered with in any way.

• Professional, industrial or high frequency use.

WARRANTY

TO ENSURE A SPEEDY RESPONSE PLEASE

HAVE THE MODEL NUMBER AND DATE OF

PURCHASE AVAILABLE. A CUSTOMER SERVICE

REPRESENTATIVE WILL TAKE YOUR CALL

AND ANSWER ANY QUESTIONS YOU MAY

HAVE RELATING TO THE WARRANTY POLICY

OR PROCEDURE.

OZITO Australia/New Zealand (Head Ofﬁce)

1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.

The beneﬁts provided under this warranty are in addition

to other rights and remedies which are available to you at law.

Our goods come with guarantees that cannot be excluded at law. You

are entitled to a replacement or refund for a major failure and for

compensation for any other reasonably foreseeable loss or damage.

You are also entitled to have the goods repaired or replaced if the

goods fail to be of acceptable quality and the failure does not amount

to a major failure.

Generally you will be responsible for all costs associated with a claim

under this warranty, however, where you have suffered any additional

direct loss as a result of a defective product you may be able to claim

such expenses by contacting our customer service helpline above.

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to

the online manual.

Produkt Specifikationer

Mærke:	Ozito
Kategori:	Ikke kategoriseret
Model:	ZLBP-015

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito ZLBP-015 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ozito Manualer

Ozito PXLMB-335 Manual

19 August 2025

Ozito PXCG-080 Manual

29 Juli 2025

Ozito PXGAR-500 Manual

29 Juli 2025

Ozito PXSK-2518 Manual

22 Juni 2025

Ozito PXBPS-1828 Manual

2 Juni 2025

Ozito PXLEK-1840 Manual

5 Januar 2025

Ozito PXBGSS-1815 Manual

10 December 2024

Ozito PXBSPS-180 Manual

6 Oktober 2024

Ozito SSH-240 Manual

6 Oktober 2024

Ozito DMC-1000 Manual

20 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

EasyMaxx 00632 Manual

3 Oktober 2025

Sony ODBK-201 Manual

3 Oktober 2025

Sony CCMC-SA10 Manual

3 Oktober 2025

Arctic Céramique 2 Manual

3 Oktober 2025

EasyMaxx 12803 Manual

3 Oktober 2025

Sony BKM-200M Manual

3 Oktober 2025

EasyMaxx 01950 Manual

3 Oktober 2025

EasyMaxx 00629 Manual

3 Oktober 2025

EasyMaxx 15642 Manual

3 Oktober 2025

Vestil EHLTP-3064-1-60-A3 Manual

3 Oktober 2025