Peavey ISM 5Tx Manual

Peavey Højttaler ISM 5Tx

Læs gratis den danske manual til Peavey ISM 5Tx (2 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om Peavey ISM 5Tx, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Architectural Acoustics® ISMTM 5Tx Loudspeaker

Enclosure Materials & Finish: Black molded ABS cabinet with matte finish.

Cabinet has UL 94 HB flame retardant plastic for safety, with matching perforated

powder-coated steel speaker grille. Also available in white.

Mounting provisions: One set of two inserts, one on the top center and one on the

bottom center for the supplied speaker bracket. One wall-mount key-hole on the rear

near the top.

Dimensions (H x W x D): Cabinet Only: 8.87 in. x 5.88 in. x 5.57 in.

225 mm x 149 mm x 141 mm

With Mounting Bracket (Approx): 10.0 in. x 5.88 in. x 8.0 in.

254 mm x 149 mm x 203 mm

Net Weight: 5.5 Lbs. (2.5 kg)

Architectural & Engineering Specifications

The loudspeaker system shall have an operating range of 65 Hz to 20 kHz. The

nominal output level shall be 88 dB when measured at a distance of one meter with

an input of one watt when in 8 Ohm Thru mode. The nominal impedance shall be

8 ohms, and the maximum continuous power handling shall be 40 watts, maximum

program power of 80 watts and a peak power input of at least 160 watts, with a

minimum amplifier headroom of 3 dB, in 8 ohm thru mode. A 70.7 V line

transformer with switched taps at 16W, 8W, 4W and 2W shall be incorporated, with

provisions for 8 ohm Thru mode as well. A 5” nominal diameter water-resistant

woofer with rubber surround shall be used in conjunction with a 1” nominal

diameter polymer dome tweeter, and a frequency dividing network shall divide the

frequencies between them at 7.4 kHz.

The nominal radiation geometry shall be 110 degrees in the horizontal plane and

110 degrees in the vertical plane. The outside dimensions shall be 8.87 inches

high by 5.88 inches wide by 5.57 inches deep. The molded plastic cabinet shall be

made from flame-retardant ABS, meeting UL 94 HB requirements. The weight

shall be 5.5 pounds. The loudspeaker system shall be a Peavey model ISM™5Tx.

2 YEAR LIMITED WARRANTY

NOTE: For details, refer to the warranty statement. Copies of this statement may

be obtained by contacting Peavey Electronics Corporation, P.O. Box 2898,

Meridian, Mississippi 39301-2898.

Architectural Acoustics® ISMTM 5Tx Loudspeaker

Product Description

The ISM™5Tx is a small format 2-way speaker system that is perfect for any application

from foreground music to speech reinforcement. The ISM™5Tx has a hi-fi sound

character with good clarity, which is ideal for music systems in bars, taverns, arenas,

lounges, arcades or anywhere multi-channel, multi-speaker sound systems are required.

This speaker utilizes a specially designed 5” woofer and a 1” poly dome tweeter. The

lightweight and rugged injection-molded cabinet is weather-resistant for indoor or

outdoor use. A curved black metal perforated grille provides driver protection and a

professional appearance.

The compact, lightweight package coupled with its smooth response makes this system

ideal for the smaller venues where space is at a premium.

The ISM™5Tx speaker system is rated at 80W program power handling. Spring-loaded

terminal input connectors make hook-up extremely simple. Incorporation of a 70.7 volt

line transformer with taps at 16W, 8W, 4W and 2W allow easy use with 70.7 volt

distributed systems. The tap selector switch also has an 8 ohm input option, so the

ISM™5Tx speaker system can be used with a direct connection to a power amp,

providing unequaled versatility.

Product Features

• Premium 5" woofer with rubber surround

• 1" polydome dynamic tweeter

• Weather-resistant

• 80 Watts program power handling

• Built-in switched 70 Volt Line transformer w/Taps at 16W, 8W, 4W, 2W

• 8 Ohms nominal position on switch

• Small lightweight molded enclosure

• Flame retardant enclosure, to UL 94 HB

• Molded-in mounting inserts

• Mounting bracket included

Mounting and Installation

CAUTION!

Before attempting to suspend or mount this speaker, consult a certified structural

engineer. Speaker can fall from improper suspension, resulting in serious injury and

property damage. The ISM™5Tx can be mounted using the supplied mounting bracket.

Use only the correct mating hardware and appropriate bracket mounting hardware. All

associated rigging is the responsibility of others.

Architectural Acoustics® ISMTM 5Tx Loudspeaker

CAUTION!

When using the 70.7V distribution system transformer inputs, it is typically required that

an infrasonic filter be used to prevent saturation of the transformer, and possible

overloading of the power amplifier. A minimum of an 18 dB/octave high-pass filter set to

a –3 dB point of 80 Hz or higher should be used to filter the low frequencies. It is

recommended that the filter be a 24 dB/octave Linkwitz-Riley type set to 65 Hz (-6 dB

point) for maximum reliability and performance.

Specifications

Frequency Range: 65Hz – 20kHz (-10 db, 1 meter on-axis, swept-sine in ½

space environment)

Frequency Response: 92Hz – 18kHz (+/- 4db, 1 meter on-axis, swept-sine in ½

space environment)

Power Handling: 8 Ohm Thru Mode: 40 W continuous, , 80 W program 160 W

peak. Transformer taps for 70.7 volt operation: 16W, 8W, 4W and 2W

Sound Pressure Level, 1 Watt, 1 meter in anechoic environment: 88 dB SPL,

(2.83V input, 8 ohm thru mode) Transformer Losses, Less than 1 dB when in .

70.7V input mode.

Maximum Sound Pressure Level (1 meter, 8 ohm thru mode): 103 dB SPL

continuous, 109 dB SPL peak

Nominal Radiation Angle: 110 degrees horizontal by 110 degrees vertical

Transducer Complement: Low Frequency Section: 1x 5” high performance

water-resistant woofer with rubber surround. High Frequency Section: 1x1”

polydome dynamic tweeter with built-in diffusion cap.

Crossover Frequency (internal passive): 7.4 kHz

Crossover Type & Slope: Internal passive; 12 dB/octave (2

nd order), High pass

for tweeter, and 6 dB/octave (1

st order) Low pass for woofer

Impedance (Z) for 8 ohms Thru connection: Nominal: 8 ohms

Minimum: 6.6 ohms

Input Connections: Spring-loaded push terminals

Transformer Taps (Transformer Input Mode): 70.7V taps: 16W, 8W, 4W, 2W

Caution: When using transformer input, an infra-sonic (high-pass) filter

should be used to prevent transformer saturation and overload. This will

increase reliability and decrease distortion. We recommend a setting of 80

Hz –3 dB point.

Produkt Specifikationer

Mærke:	Peavey
Kategori:	Højttaler
Model:	ISM 5Tx

Har du brug for hjælp?

Hvis du har brug for hjælp til Peavey ISM 5Tx stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Peavey Manualer

Peavey 1208-8 SPS BWX RB Manual

9 August 2025

Peavey 1208-4 SPS BWX RB Manual

9 August 2025

Peavey PVXp 15 DSP Manual

15 November 2024

Peavey Messenger M100 Manual

12 November 2024

Peavey RBN 215 Manual

18 September 2024

Peavey PVs 18 Manual

15 September 2024

Peavey SP 218P Manual

14 September 2024

Peavey S-12825 RB Manual

31 August 2024

Peavey SSE 10 Manual

22 August 2024

Peavey RBN 118 Manual

16 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Bose SoundLink Max Manual

14 September 2025

Moonki MW-PB265BLT Manual

13 September 2025

Moonki MW-PB250 Manual

13 September 2025

Morel Tempo Ultra Integra 602 Manual

13 September 2025

Moonki MS-900B Manual

13 September 2025

Moonki MO-PB280 Manual

13 September 2025

Moonki MS-P112B Manual

13 September 2025

Morel Tempo Ultra Integra 692 Manual

13 September 2025

Moonki MS-P15BW Manual

13 September 2025

Moonki MS-112DSP Manual

13 September 2025