PetSafe 62350 Manual

PetSafe Ikke kategoriseret 62350

Læs gratis den danske manual til PetSafe 62350 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 58 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 29.5 anmeldelser. Har du et spørgsmål om PetSafe 62350, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

131203

Pet Safety Seat™

Care & Use Guide

Thank you for purchasing the Solvit Pet Safety Seat. Check to make sure the contents include a fabric cover with

tether in polybag; a three-panel plastic main Seat section; and the following plastic sections: Front Strut; Rear Strut;

Right Wall; and Left Wall (name embossed on the side of each).

Assembly: (Make sure the smooth side of each plastic panel faces “in” and the side with round depressions faces

“out”). Insert tab A on Front Strut into slot A in Left Wall and slide Front Strut in the direction of the arrow until tab

A is in the fully locked position.

Repeat this procedure to lock tab B on Front Strut into slot B on Right Wall, and to lock tabs C and D on Rear Strut

into slots C and D on the Left and Right Wall sections.

The main Seat section is a three-panel piece that was

folded in a “Z” shape in the package. Before

connecting to the Left and Right Wall sections, fold

the Seat section into a “U” shape with the smooth

sides facing “in”. Insert double-tab E on the front

panel of the Seat section into slot E on the Left Wall

and slide to lock. Repeat for tab G then repeat for

tabs F and H into the corresponding slots on the

Right Wall.

Place the assembled plastic frame upside-down on a clean surface. The

Outer Fabric Shell has a zipper and small tags marked Z (next to zipper)

and X (on opposite seam). With zipper in the fully open position, slide the

fabric shell over the plastic frame so the Z seam aligns with the H corner at

the back of the plastic frame and the X seam aligns with the G corner.

SOLVIT Products, LP 1114 W Harris Rd, Suite 101  Arlington, TX 76001

Tel: 866-6-SOLVIT (866-676-5848)  Fax: (817) 466-2291

Email: customerservice@solvitproducts.com www.solvitproducts.com 

Pull the sides of the fabric shell down all four sides of the plastic frame

until the rectangular bottom panel of the fabric shell aligns with the

rectangular bottom of the plastic frame.

Turn the entire assembly right-side-up and pull the fabric shell up and

over the top edges of the plastic seat, and close the zipper. The seat

should now look like the image below and the two seat belt slits in the

fabric shell should align with the holes in the plastic frame.

The underside of the Top Fabric Liner includes two small

tags marked X and Z. Insert the top liner into the seat

portion of the plastic frame so the X and Z seams on the

inner liner align with the X and Z seams on the fabric outer

shell. Fit the upper edge of the fabric liner over the rear

wall of the plastic frame and fasten the loop tape pieces on

the top liner with the hook tape pieces on the outer shell.

Pass the large loop end of the safety tether (opposite the

carabineer), through the slit sewn into the lower edge of

the back panel of the top liner and through the slit in the

plastic Seat section. Fit the upper edges of the other

three sides of the top liner over the edges of the plastic

frame and fasten the hook and loop tape strips for each

side. Finally, insert the reversible pillow.

To install in vehicle, place the Safety Seat on the vehicle

seat and pass the seat belt through the holes in the fabric and plastic frame on one side of the Safety Seat. Thread the

seat belt through the large loop on the end of the safety tether, all the way through the frame and out the holes on the

opposite side, then buckle. Tug the safety tether firmly to make sure it is attached to the seat belt and adjust to desired

length. Place pet in the Safety Seat, attach the tether, and it’s ready to go! For multiple pets, extra tethers are

available – contact Solvit customer service at the number below.

Safety: We recommend using a harness, rather than a collar, when traveling. The safety tether can be attached to any

harness, but for maximum safety, we recommend the Solvit Deluxe Vehicle Safety Harness, sold separately.

Cleaning: Fabric pieces can be machine washed in cold - machine dry without heat or line dry.

Limited Lifetime Warranty: The Pet Safety Seat is warranted to be free from defects in materials or workmanship for

the life of the product. Some restrictions apply, so please visit our website for more details. A copy of the original

sales receipt is required for warranty issues.

Solvit Products is dedicated to offering innovative solutions to improve pets’ quality of life. Please feel free to

Produkt Specifikationer

Mærke:	PetSafe
Kategori:	Ikke kategoriseret
Model:	62350

Har du brug for hjælp?

Hvis du har brug for hjælp til PetSafe 62350 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret PetSafe Manualer

PetSafe Freedom PPA00-10859 Manual

15 Juli 2025

PetSafe PBC00-12726 Manual

15 Juli 2025

PetSafe PDT00-16030 Manual

15 Juli 2025

PetSafe Staywell 919SGIFD Manual

15 Juli 2025

PetSafe PPA19-16732 Manual

9 Juli 2025

PetSafe PPA19-16731 Manual

9 Juli 2025

PetSafe Staywell 932EF Manual

6 Juli 2025

PetSafe SmartDoor PPA19-15791 Manual

29 Marts 2025

PetSafe PBC17-14777 Manual

8 Oktober 2024

PetSafe ScoopFree PAL19-14656 Manual

7 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman MY500XT Manual

1 August 2025

Navman FOCUS150 GPS Manual

1 August 2025

Scheppach TW1000 Manual

1 August 2025

Navman MiVue 750 WIFI Manual

1 August 2025

Navman MiVue Drive FHD Manual

1 August 2025

Midea MEC64 Manual

1 August 2025

Navman MY50T Manual

1 August 2025

Navman M100 Manual

1 August 2025

Navman MiVue 770 SAFETY Manual

1 August 2025

Navman MiVue 790 Manual

1 August 2025