Philips GearUnits ECM 330 Manual

Philips Ikke kategoriseret GearUnits ECM 330

Læs gratis den danske manual til Philips GearUnits ECM 330 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Philips GearUnits ECM 330, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

4411 102 68142

12/2014

Data subject to change

Printed in France

www.philips.com/lighting

1/2

Mounting instructions

-30°C

Philips GearUnits ECM 330

PF>0.97MHN-SEH 2000W

MHN-LA 1000W

EN61347

MAINS

277-480V 50-60Hz

220-480V 50-60Hz 3.4

3.4 +55°C

-30°C +55°C

2100

1040

8.2-4.7

5.1-2.3

9.5

240

145 PF>0.97

530x143x127

1. Lamp currents are approximate data. For exact data refer to the lamp data sheet.

2. Ignitor on the luminaire, not on the gear unit.

Maximum distance in between e-ballast gear unit and floodlight is 80 m for 1000 W and 120 m for 2000 W versions.

See below table for recommended cable cross sections.

3. Current ripple: <10 %.

4. Earth leakage current: 480 V, 50-60 Hz <3.5 mA.

5. Output power tolerance: ±5 %.

6. Mains supply voltage fluctuation not more than -8 % and +6 % from the rated voltage of the ballast.

ECM 330

120.7

143

530

28.5 240

80 127.4

12.7

6.3

126

472

530

460

143

13.75

8.5

Warning high leakage current earth connection

essential before connecting supply

(5.1.7.1 of IEC60950-1)

1.5 mm2

1000 W

2.5 mm2

4 mm2

6 mm2

2000 W

Less then 20 m

20 to 40 m

40 to 60 m

60 to 80 m

Less then 35 m

35 to 60 m

60 to 85 m

85 to 120 m

FLOODLIGHT

CONNECTION

1.2 Nm

Exercise appropriate care in the handling of high voltages. Do not touch any conductive parts during operation.

Ensure the units are disconnected from the mains before exchanging the lamp connected to the PSU / ignitor resp. in to the end application. The residual charge

left on the capacitors is a danger to life if the units are still connected to mains!

Caution: The residual charge on the capacitors can be a danger to life even if the units are disconnected from the mains. Please handle with care!

Both electronic lamp ballast and ignitor must never be installed or operated in an explosive or volatile atmosphere. Never use the ballast or ignitor near

flammable

gases or liquids. See that there will be no moisture, dust or similar which could lead to short circuits or fire.

Before using the ballast or ignitor in any kind of outdoor application you have to take additional measures and observe special requirements. If you are uncertain,

contact Philips.

No potential isolation is provided between line input and output. Accidentally grounding of an output terminal by direct contact or arcing to GND can damage

the unit (no warranty replacement).

The unit is designed for case mounting. Due observation of electrical safety and RFI suppression code requirements is mandatory in all applications.

See that sufficient cooling of EPS and ignitor is provided.

All installation and repair work on this unit is only permitted by qualified personnel. Always comply with local safety requirements when operating the unit

uncased.

Extreme care must be taken when testing the unit live. The use of an isolating transformer is mandatory. On no account may grounded test instruments / meters

be used for this purpose!

Philips does not assume liability for disregarding of this notice, incorrect use of the EPS and ignitor or dis-regarding of any legal requirements.

This product is subject to technical changes without prior notice.

It is essential to isolate the electronic ballast/ignitor or the connected luminaire electrically from mains voltage before maintenance !

Do not attempt to handle or operate an electronic power supply (EPS) and ignitor before completely reading and understanding this notice.

Contact Philips if you are uncertain of hazards associated with these devices.

The Ballast and the ignitor produces starting voltages of up to 11 kV and electromagnetic radiation interference which are hazardous to

personnel and sensitive instrumentation.

*) After under voltage protection activation, driver start again

when Umains return to nominal value

After over voltage protection activation, driver start again when

Umains will off during 30 sec. and then return to nominal value.