Philips SQM7441 Manual

Philips Ikke kategoriseret SQM7441

Læs gratis den danske manual til Philips SQM7441 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Philips SQM7441, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
A
BC
D
E
F
G
H
**
1 2 3
4
5
6
Engli s h
1 Important safety instructions
Caution
•Read these instructions before you begin. If you are unsure
of any part of the process, contact a professional contractor
or installer for assistance. Improper installation can result in
injury or damage.
•The wall or mounting surface must be capable of supporting
the combined weight of the mount and the display; if not, the
structure must be reinforced.
•Locate pipes, wires, or any other hazards in the wall where
you wish to install the mount before drilling.
•Safety gear and proper tools must be used. Failure to do so
can result in injury or damage.
•Two people are recommended for installation. Do not
attempt to lift a heavy display without assistance.
•Follow all instructions and recommendations regarding
adequate ventilation and suitable locations for mounting
your display. Consult the owner‘s manual for your par ticular
display for more information.
•This wall mount is intended for use only with the maximum
weight of 25 kg (55 lbs). Use with heavier than the maximum
weights indicated may result in instability causing possible
injury.
2 Tilt wall mount (for LCD, Plasma, and LED
displays)
What's in the box
Wall plate (x1)
Mount arm (x2)
User manual (x1)
Hardware kit (x1)
Hardward kit
A
M8 x 63 screw (x2)
B
Lag bolt washer (x2)
C
Concrete anchor (x2)
D
M4 x 12 screw (x4)
E
M6 x 12 screw (x4)
F
M8 x 12 screw (x4)
G
M6 washer (x4)
H
M8 washer (x4)
Tools required
• Phillips head screw driver
• Ratchet or driver with 13 mm (1/2”) socket
• Electric or portable drill
• 6 mm (1/4”) drill bit and stud nder for drywall
installation
• 10 mm (3/8”) Masonry bit for concrete installation
3 Installation
Mount to the drywall
Caution
For safety reasons, this mount must be secured to at least two
wood studs no less than 16” apart. The studs must be capable
of suppor ting the combined weight of the mount and display.
1 Use a high quality stud nder to locate two adjacent
studs where you wish to install your mount. Mark
both edges of each stud to help identify the exact
center.
Note
You must use the center of each stud to avoid cracking or
splitting the wood during installation.
2 Place the wall plate against the wall with the arrow
pointing up and level it using the integrated bubble
level.
3 While another person holds the wall plate in
position, mark two locations (one per stud) for
securing the mount to the wall (see Fig. 1).
4 Set the wall plate aside and drill a 6 mm (1/4”) pilot
hole at each marked location.
5 Place the wall plate back against the wall and attach
it using the lag bolts
A
and lag bolt washers
B
provided (see Fig. 2). Do not over-tighten these
bolts and do not release the wall plate until both
bolts are in place. Ensure that the wall plate remains
level after tightening the bolts.
Mount to the concrete wall
Caution
For safety reasons, the concrete wall must be capable of
suppor ting the combined weight of the mount and the display.
The manufacturer takes no responsibility for failure caused by
walls of insufcient strength.
1 Place the wall plate against the wall in the desired
location and level it using the integrated bubble level.
2 While another person holds the wall plate in place,
mark two locations on the wall for securing the
mount (see Fig. 3).
3 Set the wall plate aside and drill a 10 mm (3/8”) hole
at each marked location. Remove any excess dust
from the holes.
4 Insert a concrete anchor
C
into each hole so that
it is ush with the concrete surface (see Fig. 4). A
hammer can be used to lightly tap the anchors into
place if necessary.
Note
If the concrete wall is covered by a layer of plaster or drywall,
the concrete anchor must pass completely through the layer
to rest ush with the concrete surface.
5 Place the wall plate back against the wall and attach
it using the lag bolts
A
and lag bolt washers
B
provided (see Fig. 2). Do not over-tighten these
bolts and do not release the wall plate until all
bolts are in place. Ensure that the wall plate remains
level after tightening the bolts.
Attaching the mount arms to the display
Caution
Use extra care during this part of the installation. If possible,
avoid facing down your display as it may damage the viewing
surface.
Note
This mount comes with a selection of different screw
diameters and lengths to accommodate a wide variety of
display models. Not all of the hardware in the kit will be
used. If you cannot nd the appropriate screw size in the kit
provided, consult the manufacturer of your display for more
information.
1 Determine the correct diameter of screw to use
carefully by trying different size (M4, M6 and M8)
from the hardware kit (see Fig.5). Do not force
any of the screws – if you feel resistance, stop
immediately and try a smaller diameter screw.
2 Attach the mount arms to the back of your display
using the screws identied in steps 1. If you are using
M6 screws you will need to use M6 washers
G
. If
you are using M8 screws you will need to use M8
washers
H
Note
The mount arms must be attached with the tilt adjustment
screws facing towards the outer edges of the display (see Fig.
6). Otherwise, the tilt function cannot be accessed..
Final assembly
1 Loosen both tilt adjustment screws and set the tilt
to the desired angle. Make sure both arms are set
to the same angle before re-tightening both screws
securely.
2 With the help of another person, carefully lift your
display and place it on the wall plate. Gently apply
pressure to the bottom of your display so that the
clips on the mount arms lock to the wall plate. Do
not release the display until the mount arms have
securely hooked onto the wall plate.
Caution
Make sure that both arms are locked to the wall plate. For
safety reasons, this mount cannot be used unless both arms
are securely locked.
SQM7441
Register your product and get support at
www.philips.com/support
User manual
Manual del usuario
sqm7441_27_2L_um_150731.indd 1-3 31/07/2015 14:56:54

Produkt Specifikationer

Mærke: Philips
Kategori: Ikke kategoriseret
Model: SQM7441

Har du brug for hjælp?

Hvis du har brug for hjælp til Philips SQM7441 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Philips Manualer

Philips

Philips Norelco Sensotouch 3D 1260XD Manual

4 November 2025
Philips

Philips Evnia 4000 Series SPK9418W Manual

4 November 2025
Philips

Philips Sonicare HX6352 Manual

3 November 2025
Philips

Philips Series 5000 MG5942 Manual

3 November 2025
Philips

Philips SHB1803C Manual

3 November 2025
Philips

Philips Avent SCF347 Manual

2 November 2025
Philips

Philips 40PFA4151S Manual

2 November 2025
Philips

Philips 49PFA4301S Manual

2 November 2025
Philips

Philips SPT7308 Manual

1 November 2025
Philips

Philips TAT2500 Manual

31 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MuxLab

MuxLab 500439 Manual

5 November 2025
GVM

GVM BL160-II Manual

5 November 2025
Uniprodo

Uniprodo UNI_ROLL_03 2in1 Manual

5 November 2025
Rockville

Rockville SS6 Manual

5 November 2025
Silk'n

Silk'n VacuPedi FTC04 Manual

5 November 2025
MEPROLIGHT

MEPROLIGHT MCO PRO Manual

5 November 2025
XPG

XPG Battlecruiser II Manual

5 November 2025
Hosa

Hosa USQ-110 Manual

5 November 2025
JMAZ

JMAZ Centipede Quadro Manual

5 November 2025
Lake People

Lake People Mic-Amp F311-D Manual

5 November 2025