Pioneer CD-R5 Manual


Læs gratis den danske manual til Pioneer CD-R5 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 44 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 22.5 anmeldelser. Har du et spørgsmål om Pioneer CD-R5, eller vil du spørge andre brugere om produktet?

Side 1/4
Installing the battery
Slide the tray out on the back of the remote con-
trol and insert the battery with the plus (+) and
minus (–) poles pointing in the proper direction.
When using for the first time, pull out the film
protruding from the tray.
WARNING
Keep the battery out of the reach of children.
Should the battery be swallowed, immediately
consult a doctor.
CAUTION
Use only one CR2025 (3V) lithium battery.
Remove the battery if the remote controller is
not used for a month or longer.
Do not recharge, disassemble, heat or dispose
of the battery in fire.
Do not handle the battery with metallic tools.
Do not store the battery with metallic materi-
als.
In the event of battery leakage, wipe the
remote control completely clean and install a
new battery.
When disposing of used batteries, please
comply with governmental regulations or envi-
ronmental public institution’s rules that apply
in your country/area.
Always check carefully that you are loading
battery with its (+) and (–) poles facing in the
proper directions.
Do not leave this unit free inside the car. When
the car stops or turns a curve, the unit might
drop on the floor. If the unit is rolled and put
under the brake pedal, it might prevent the
driver from braking well, causing a serious
trouble.
Do not disassemble or modify this unit. To do
so may cause a fault.
The volume of the car stereo should be so
adjusted that you can hear a loud sound
occurring outside your car. If any happening
sound outside your car is deafened by music
from the car stereo when you are driving, this
condition can be a factor of being involved in a
traffic accident.
(+) pole
Battery holder
Before you start
Using the remote control
operation mode switch
There are three remote control operation modes
on this remote control.
AVH mode operation
When operating an AV-Receiver (e.g. AVH-
P5700DVD) with this remote control, remote
control operation mode switch is normally
switched to AVH.
DVD mode operation
When operating a Pioneer DVD player with this
remote control, operation mode switch is nor-
mally switched to DVD. If you switch the remote
control operation mode switch to , theDVD
joystick and  operations are changed for
DVD player.
TV mode operation
When operating a Pioneer TV tuner (e.g. GEX-
P5700TV(P) or GEX-P5750TV(P)) with this remote
control, operation mode switch is normally
switched to . If you switch the remote controlTV
operation mode switch to TV, the joystick opera-
tion is changed for TV tuner.
Setting the remote control code
type
When the remote control operation mode switch
is set to DVD, changing the remote control code
type enables you to operate the Pioneer DVD
player with this remote control. There are three
remote codes, code type A, code type Band
code type AVH.
To operate a multi-DVD player
When operating a multi-DVD player (e.g.
XDV-P9II), select code A.
To operate a DVD navigation unit
When operating a DVD navigation unit,
select code B.
To operate an AV-Receiver
When operating an AV-Receiver (e.g. AVH-
P5700DVD), select code AVH.
1 Set the remote control code selection
switch on the left side of the remote control to
the appropriate position with a pen tip or other
pointed instrument.
If you select AVH mode, there is no need to
take the following procedure.
If you select A/B mode, take the following
procedure and change the code type to the
appropriate type.
2 Press and on the remote control simul-
taneously to change the code type.
Initially, the code type is set to . Each time youA
press  and simultaneously on the remote
control the code type switches between Aand
B.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful inter-
ference, and (2) this device must accept any
interference received, including interference
that may cause undesired operation.
Information to User
Alteration or modifications carried out with-
out appropriate authorization may invalidate
the user's right to operate the equipment.
Before you startBefore you start
PIONEER CORPORATION
4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404
PIONEER EUROPE N.V.
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium
TEL: (0) 3/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936
TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia
TEL: (03) 9586-6300
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada
TEL: 1-877-283-5901
PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.
Blvd.Manuel Arila Camacho 138 10 piso
Col.Lomas de Chapultepec, Mexico, D.F. 11000
TEL: 55-9178-4270
Published by Pioneer Corporation.
Copyright © 2004 by Pioneer Corporation.
All rights reserved.
Publication de Pioneer Corporation.
Copyright © 2004 Pioneer Corporation.
Tous droits de reproduction et de traduction
réservés.
Printed in Japan
Imprimé au Japon
<CZR5026-A> E<KSNZX> <05C00000>
Remote control for DVD-VIDEO
Télécommande pour DVD-VIDEO
Owner’s Manual
Mode d’emploi
CD-R5
Using the remote control
Point the remote control in the direction of the
front panel to operate.
The remote control may not function properly
in direct sunlight.
Precaution
Do not store the remote control in high tem-
peratures or direct sunlight.
Do not let the remote control fall onto the floor,
where it may become jammed under the brake
or accelerator pedals.
Specifications
Power source ...................... 3 V DC
(Lithium Battery: CR2025)
Dimensions (W ×H ×D): .... 52 × ×123 11 mm
Weight ................................. 50 g (including battery)
Infered Remote Control
<Wavelength> .................. 945 nm
<Output> .......................... typ; 10 mw/sr per infrared
LED
Note
Specifications and the design are subject to
possible modification without notice due to
improvements.
Button names and
operation
TV mode operation
Remote control code selection switch
Switch to change the setting of the remote
control. In this case, set to AVH.
VOLUME (y z/ ) buttons
Press to increase or decrease the volume.
Remote control transmitter
ATT (C) button
Press to quickly lower the volume level.
Press once more to return to the original
volume level.
SOURCE (m) button
Press to cycle through all the available
source. Press and hold to turn the source
off.
Joystick
Move to do manual seek tuning and preset
tuning. Click to recall the menu. Also used
for controlling functions.
Remote control operation mode switch
Switch the operation mode between AVH,
DVD and TV TVmodes. In this case, set to .
DIRECT (F) button
Press to do direct channel select. Press and
hold to turn BSSM on or off when the
Pioneer TV tuner (GEX-P5700TV(P) or GEX-
P5750TV(P)) is used.
BOOKMARK (B) button
Not used.
BACK (w) button
Not used.
BAND (v) button
Not used.
ENTERTAINMENT (x) button
Not used.
FORWARD (d) button
Not used.
STOP (h) button
Not used.
NEXT (g) button
Not used.
CLEAR (;) button
Not used.
NUMBER (0 : ) buttons
Not used.
PREVIOUS (e) button
Not used.
REVERSE (b) button
Not used.
PLAY/PAUSE (c) button
Not used.
ANGLE (r) button
Not used.
STEP (f a/ ) button
Not used.
SUBTITLE (q) button
Not used.
DISPLAY (u) button
Not used.
AUDIO (p) button
Not used.
RETURN (t) button
Not used.
MENU (o) button
Not used.
TOP MENU (s) button
Not used.
Button names and
operation (TV mode)
DVD mode operation
Remote control code selection switch
Switch to change the setting of the remote
control. Refer to Setting the remote control
code type and switch to the appropriate
setting.
VOLUME (y z/ ) buttons
Press to increase or decrease the volume.
Remote control transmitter
ATT (C) button
Press to quickly lower the volume level.
Press once more to return to the original
volume level.
SOURCE (m) button
Remote control code : A or B
Press to turn the DVD player on or off.
Remote control code : AVH
Press to cycle through all the available
source. Press and hold to turn the source off.
Joystick
Move to fast forward, reverse and track
search controls. Also used for controlling
functions.
Remote control operation mode switch
Switch the operation mode between AVH,
DVD and TV modes. In this case, set to
DVD.
DIRECT (F) button
Not used.
BOOKMARK (B) button
Press to turn the Bookmark function on or
off when your DVD player features bookmark
function. For details, refer to DVD players
operation manual.
BACK (w) button
Remote control code : A
Press to select the next disc when the multi-
DVD player is connected.
Remote control code : B or AVH
Not used.
BAND (v) button
Press to switch mode between MP3/WMA
and audio data (CD-DA) when playing discs
with MP3/WMA and audio data (CD-DA)
such as CD-EXTRA and MIXED-MODE CDs.
ENTERTAINMENT (x) button
Remote control code : A
Press to select the previous disc when the
multi-DVD player is connected.
Remote control code : B or AVH
Not used.
FORWARD (d) button
Press to perform fast forward.
STOP (h) button
Press to stop playback.
NEXT (g) button
Press to go to the next track (chapter).
CLEAR (;) button
Press to cancel the input number when
0 :are used.
NUMBER (0 : ) buttons
Press to directry select the desired track,
chapter or disc.
PREVIOUS (e) button
Press to return to the previous track (chap-
ter).
REVERSE (b) button
Press to perform fast reverse.
PLAY/PAUSE (c) button
Press to switch seqentially between play-
back and pause.
ANGLE (r) button
Press to change the viewing angle during
DVD playback.
STEP (f a/ ) button
Press to move ahead one frame at a time
during DVD/Video CD playback. Press and
hold for one second to activate slow play-
back.
SUBTITLE (q) button
Press to change the subtitle language dur-
ing DVD playback.
DISPLAY (u) button
Press to select different displays.
AUDIO (p) button
Press to change the audio language during
DVD playback.
RETURN (t) button
Press to display the PBC (playback control)
menu during PBC playback.
MENU (o) button
Press to display the DVD menu during DVD
playback.
TOP MENU (s) button
Press to return to the top menu during DVD
playback.
Button names and
operation (DVD mode)
AVH mode operation
Remote control code selection switch
Switch to change the setting of the remote
control. In this case, set to AVH.
VOLUME (y z/ ) buttons
Press to increase or decrease the volume.
Remote control transmitter
ATT (C) button
Press to quickly lower the volume level.
Press once more to return to the original
volume level.
SOURCE (m) button
Press to cycle through all the available
source. Press and hold to turn the source
off.
Joystick
Move to fast forward, reverse and track
search controls. Click to recall the A.Menu.
Also used for controlling functions.
Remote control operation mode switch
Switch the operation mode between AVH,
DVD and TV modes. In this case, set to
AVH.
DIRECT (F) button
Press to do direct number select.
BOOKMARK (B) button
Press to operate the preprogrammed func-
tions for each source. For details, refer to AV-
Receivers operation manual.
BACK (w) button
Press to return to the previous display.
BAND (v) button
Press to select among FM and AM bands
when the tuner is selected as a source. Also
used to cancel the control mode of func-
tions.
ENTERTAINMENT (x) button
Press to switch between the background
displays.
FORWARD (d) button
Press to perform fast forward.
STOP (h) button
Press to stop playback.
NEXT (g) button
Press to go to the next track (chapter).
CLEAR (;) button
Press to cancel the input number when
0 :are used.
NUMBER (0 : ) buttons
Press  to directry select the deseired
track, preset tuning or disc. Buttons  
can operate the preset tuning for the tuner
or disc number search for the multi-CD
player.
: Not used.
PREVIOUS (e) button
Press to return to the previous track (chap-
ter).
REVERSE (b) button
Press to perform fast reverse.
PLAY/PAUSE (c) button
Press to switch seqentially between play-
back and pause.
ANGLE (r) button
Press to change the viewing angle during
DVD playback.
STEP (f a/ ) button
Press to move ahead one frame at a time
during DVD/Video CD playback. Press and
hold for one second to activate slow play-
back.
SUBTITLE (q) button
Press to change the subtitle language dur-
ing DVD playback.
DISPLAY (u) button
Press to select different displays.
AUDIO (p) button
Press to change the audio language during
DVD playback.
RETURN (t) button
Press to display the PBC (playback control)
menu during PBC playback.
MENU (o) button
Press to display the DVD menu during DVD
playback.
TOP MENU (s) button
Press to return to the top menu during DVD
playback.
Button names and
operation (AVH mode)
Key Finder
Remote control code selection switch
VOLUME (y z/ ) buttons
Remote control transmitter
ATT (C) button
SOURCE (m) button
Joystick
Remote control operation mode switch
DIRECT (F) button
BOOKMARK (B) button
BACK (w) button
BAND (v) button
ENTERTAINMENT (x) button
FORWARD (d) button
STOP (h) button
NEXT (g) button
CLEAR (;) button
NUMBER (0 : ) buttons
PREVIOUS (e) button
REVERSE (b) button
PLAY/PAUSE (c) button
ANGLE (r) button
STEP (f a/ ) button
SUBTITLE (q) button
DISPLAY (u) button
AUDIO (p) button
RETURN (t) button
MENU (o) button
TOP MENU (s) button


Produkt Specifikationer

Mærke: Pioneer
Kategori: Ikke kategoriseret
Model: CD-R5

Har du brug for hjælp?

Hvis du har brug for hjælp til Pioneer CD-R5 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Pioneer Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer