Pioneer DVR-112D Manual

Pioneer Ikke kategoriseret DVR-112D

Læs gratis den danske manual til Pioneer DVR-112D (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Pioneer DVR-112D, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

D I RIVE NSTALLATION

IN N A INSTANT

Step 1 – Prepare the Computer

1) Turn OFF the computer and disconnect the power cord.

2) Remove the bezel and the open drive bay cover from the computer’s front panel.

Note: Your computer may be a tower

model as shown on the left or a

desktop model as shown below. This

drive works in either PC model style.

Step 2 – Prepare the Drive

3) Attach slide rails to the drive if required for your drive model.

Slide rails are sold separately through computer retailers.

4) Position the drive close to the open computer bay.

Horizontal Installation Vertical Installation

Step 3 – Connect the Cables

5) Connect the power cable from the computer to the drive.

Pay close attention to the polarity of the cable.

6) Connect the IDE cable to the drive.

C onfirm that Pin 1 on the drive corresponds to Pin 1 on the cable.

7) Connect the drive’s audio output to the sound card if one is present.

D I RIVE NSTALLATION

IN N A INSTANT

Step 4 – Finish the Installation

8) Place the mounting screws in the appropriate holes and tighten by hand.

When mounting screws are loose, vibrations from the spinning disc may cause a ripping sound.

9) Replace the bezel and power ON the computer.

Setting the Jumper For Use in a Master/Slave PC

If you have a Master/Slave type of computer, you probably have two IDE channels, Primary and Secondary. The hard

drive is using the Primary IDE channel and any drives are using the Secondary channel. Install this drive as the Master

device on the Secondary channel and any other devices as Slaves o this new drive. Follow the directions below to

change your older drives or other equipm device.

2) Remove the drive from the drive bay.

3) Use your fingers or

ent on the Secondary channel to a Slave

1) Disconnect the following drive cables in the order listed below.

• Power cable

• IDE cable

• Audio cable

a tool to move the jumper to the new setting.

4) Return the drive to the drive bay.

5) Reconnect the cables in the reverse order, Audio, IDE then Power.

Jumper: (jumpered

= ON; no jumper

= OFF)

Set the jumper to select the drive type for your computer.

Pin Name Function

1 MA on Drive set to Master mode

2 SL on Drive set to Slave mode

3 on Drive set to Cable Select mode CS

4 Reserved

5 Reserved

Slave Cable Select Master

Setting the Jumper For Use in a Cable-Select PC

Some computer pport a e n f your PC uses Cable Select then all devices

need to be set to Cable Select as well. Also, the IDE cable must be designed for Cable Select communication.

Simply position the jumper r Cab d install the drive according to the instructions beginning on the opposite

ide of this paper. No other changes are required when usin ble Select computers.

Do Not jumper the drive to Cable Select unless your PC uses this method.

s su a dat xcha ge method called Cable Select. I

fo le Select an

s g Ca

Produkt Specifikationer

Mærke:	Pioneer
Kategori:	Ikke kategoriseret
Model:	DVR-112D
Vægt:	900 g
Produktfarve:	Beige
Dimensioner (BxDxH):	148 x 180 x 42.3 mm
Intern:	Ja
CD-læsehastighed:	- x
CD-skrivehastighed:	40 x
CD omskrivningshastighed:	32 x
CD-R skrivehastighed:	40 x
CD-RW skrivehastighed:	20 x
DVD-R skrivehastighed:	18 x
DVD-R dobbeltlags skrivehastighed:	10 x
DVD-RW skrivehastighed:	6 x
DVD+R skrivehastighed:	18 x
DVD+R dobbeltlags skrivehastighed:	10 x
DVD+RW skrivehastighed:	8 x
Drevenhed, bufferstørrelse:	2 MB
CD-R læsehastighed:	40 x
CD-RW læsehastighed:	32 x
DVD-ROM læsehastighed:	16 x
CD-ROM læsehastighed:	40 x
DVD-drev tilfældig middeltilgangstid:	130 ms
CD-ROM-drev gennemsnitlig tilfældig adgangstid:	120 ms