Planet IGS-510TF Manual

Planet Ikke kategoriseret IGS-510TF

Læs gratis den danske manual til Planet IGS-510TF (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Planet IGS-510TF, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET Compact Industrial 4-Port

10/100/1000T + 1-Port 100/1000X SFP Gigabit Ethernet Switch,

IGS-510TF. In the following sections, the term “Industrial Gigabit

Ethernet Switch” means the IGS-510TF.

Open the box of the Industrial Gigabit Ethernet Switch and carefully

unpack it. The box should contain the following items:

Industrial Gigabit

Ethernet Switch x 1

User’s Manual x 1 Wall-mount Kit x 1

DIN-rail Kit x 1 RJ45 Dust Caps x 4 SFP Dust Cap x 1

If any of these are missing or damaged, please contact your dealer

immediately; if possible, retain the carton including the original

packing material, and use them again to repack the product in case

there is a need to return it to us for repair.

Switch Fabric 10Gbps

Throughput

(packet per

second)

7.4Mpps@64bytes

Address Table 2K entries

Buer Memory 4M bits on-chip buer memory

Jumbo Frame 9Kbytes

Flow Control

Back pressure for half duplex

IEEE 802.3x pause frame for full duplex

Standards Conformance

Regulatory

Compliance

FCC Part 15 Class A, CE

Stability Testing

IEC 60068-2-32 (free fall)

IEC 60068-2-27 (shock)

IEC 60068-2-6 (vibration)

Standards

Compliance

IEEE 802.3 Ethernet

IEEE 802.3u Fast Ethernet

IEEE 802.3ab Gigabit Ethernet

IEEE 802.3az Gigabit SX/LX

IEEE 802.3x Full-Duplex Flow Control

IEEE 802.3az Energy Ecient Ethernet (EEE)

IEEE 802.1p Class of Service

Environment

Temperature

Operating: -40~75 degrees C

Storage: -40~75 degrees C

Humidity

Operating: 5~90% (non-condensing)

Storage: 5~90% (non-condensing)

Note

The wire gauge for the terminal block should be in the

range between 12 and 24 AWG.

Note

1. The power input range is for Indus9V ~ 48V DC -

trial Gigabit Ethernet Switch and supports 24V AC

2. Use one power input when using 24V AC.

3.5 Grounding the Device

Users MUST complete grounding wired with the device; otherwise,

a sudden lightning could cause fatal damage to the device.

Max. Fault Alarm Loading: 24V, 1A

V1+

V2+

PWR1

PWR2Alarm

DC Input: 9-48V

, 0.28A max.

AC Input: 24V

, 0.3A max.

1 2 3 4 5 6

Earth Ground

Note

EMD (Lightning) DAMAGE IS NOT COVERED UNDER

WARRANTY.

3.2 LEDDenition:

LED Color Function

P1 Green Lights to indicate power input 1 has power.

P2 Green Lights to indicate power input 2 has power.

1000

LNK/ACT

Green

Lights to indicate the port is running at

1000Mbps speed and successfully established.

Blinks to indicate that the Switch is actively

sending or receiving data over that port.

10/100

LNK/ACT

Amber

Lights to indicate the port is running

at 10/100Mbps speed and successfully

established.

Blinks to indicate that the Switch is actively

sending or receiving data over that port.

3.3 Switch Upper Panel

The upper panel of the Industrial Gigabit Ethernet Switch consists

of one terminal block connector within two power input.

V1+

V1-

PWR1

V2+

V2-

PWR2

DC Input: 9-48V , 0.6A max.

AC Input: 24V , 0.3A max.

1 2 3 4

Figure2: IGS-510TF Top View

2.ProductSpecications

Model IGS-510TF

Hardware Specications

Copper Ports

4 10/100/1000BASE-T RJ45 auto-MDI/MDI-X

ports

SFP Slot

1 1000BASE-SX/LX/BX SFP interface

compatible with 100BASE-FX SFP

Connector

Removable 4-pin terminal block

Pin 1/2 for Power 1; Pin 3/4 for Power 2

Power

Requirements

9~48V DC, redundant power with reverse

polarity protection, power support24V AC

Power

Consumption

(Ethernet Full

Loading)

Max. 2.4 watts/8.1BTU

Dimensions

(W x D x H)

70 x 104 x 30 mm

Weight 239g

Enclosure IP30 metal case

Installation DIN-rail kit and wall-mount kit

ESD Protection 6KV

EFT Protection 6KV

Switch Specications

Switch

Architecture

Store-and-Forward

3. Hardware Introduction

3.1 Switch Front Panel

The front Panel of the Industrial Gigabit Ethernet Switch consists of

Ethernet interfaces and LED indicators.

 Front View

P1 P2

IGS-510TF

ACTLNK

1000

10/

100

Figure1: IGS-510TF Front View

3.4 Wiring the Power Inputs

The terminal block connector on the top panel of Industrial Gigabit

Ethernet Switch is used for two redundant power inputs. Please

follow the steps below to insert the power wire.

Caution

When performing any of the procedures like inserting

the wires or tightening the wire-clamp screws, make

sure the power is OFF to prevent from getting an

electric shock.

1. Insert positive and negative DC power wires into contacts 1 and

2 for POWER 1, or contacts 3 and 4 for POWER 2.

V1+

V1-

PWR1

V2+

V2-

PWR2

DC Input: 9-48V , 0.6A max.

AC Input: 24V , 0.3A max.

1 2 3 4

2. Tighten the wire-clamp screws for preventing the wires from

loosening.

1 2 3 4

Power 1 Power 2

+ - + -

4. Installation

This section guides you to installing the Industrial Gigabit Ethernet

Switch on the DIN rail and wall. Please read this chapter completely

before continuing.

Note

This following pictures show how to install the device.

However, the device in the picture is not IGS-510TF.

4.1 DIN-rail Mounting Installation

4.2 Wall-mount Plate Mounting

Produkt Specifikationer

Mærke:	Planet
Kategori:	Ikke kategoriseret
Model:	IGS-510TF
Kode for international beskyttelse (IP):	IP30
Bredde:	30 mm
Dybde:	70 mm
Højde:	104 mm
Vægt:	252 g
Produktfarve:	Blå
Opbevaringstemperatur (T-T):	-40 - 75 °C
Relativ luftfugtighed ved drift (H-H):	5 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	5 - 90 %
Ethernet LAN-porte (RJ-45):	4
Driftstemperatur (T-T):	-40 - 75 °C
Ethernet LAN-datahastigheder:	10,100,1000 Mbit/s
Husmateriale:	Metal
Forbindelsesteknologi:	Ledningsført
Certificering:	FCC Part 15 Class A, CE
Strømforbrug (maks.):	2.8 W
Netværksstandarder:	IEEE 802.1p, IEEE 802.3, IEEE 802.3ad, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x
LED-indikatorer:	Strøm
Kan monteres på væggen:	Ja
Harmoniseret systemkode (HS):	85176990
Indgangsspænding:	9 - 48 V
Intern:	Ingen
Maksimal dataoverførselshastighed:	1000 Mbit/s
DC indgangsspænding:	9 - 48 V
Indgangsstrøm:	24 A
Fiber optisk strømstik:	SFP
Maksimal overførselsafstand:	100 m
Bølgelængde:	- nm
Fuld duplex:	Ja
Strøm over Ethernet (PoE):	Ingen
Ethernet-grænsefladetype:	Gigabit Ethernet
Switch-type:	Ikke administreret
10G understøttelse:	Ingen
Auto MDI/MDI-X:	Ja
Flowkontrol support:	Ja
Basis omskiftning RJ-45 Ethernet porte, antal:	4
Basis omskiftning RJ-45 Ethernet porttype:	Gigabit Ethernet (10/100/1000)
Opbevar-og-frem:	Ja
MAC adresselabel:	4000 entries
Switch kapacitet:	10 Gbit/sek.
Gennnemløb:	7.4 Mpps
Jumbo Frames support:	Ja
Jumbo rammer:	9000
Varmeafgivelse:	9.5 BUT/t
Antal SFP modulslots:	1
Halv dupleks:	Ja
DIN-skinne montering:	Ja
Auto-forhandling:	Ja
Understøttede kabeltyper:	Cat3, Cat4, Cat5, Cat5e, Cat6
Fiberkanal porte:	1
Duplex system:	Full, Half
Indgående omregner interface:	10Base-T, 100Base-T, 1000Base-T
Udgående omregner interface:	1000Base-BX, 1000Base-LX, 1000Base-SX