Planet IGTP-825AT Manual

Planet Ikke kategoriseret IGTP-825AT

Læs gratis den danske manual til Planet IGTP-825AT (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Planet IGTP-825AT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

- 2 - - 4 - - 6 - - 8 -

- 1 - - 3 - - 5 - - 7 -

1. Package Contents

Thank you for purchasing PLANET Industrial IP67 1000BASE-X SFP to

10/100/1000BASE-T 802.3at PoE+ Media Converter, IGTP-825AT. In the

following sections, the term means “Outdoor PoE+ Media Converter”

the IGTP-825AT.

Open the box of the Outdoor PoE+ Media Converter and carefully

unpack it. The box should contain the following items:

IGTP-825AT x 1

Power Cable with 2-pin

Terminal Block x 1

M22 Waterproof

Cable Gland x 3

User's Manual x 1 Wall-mounted Kit x 1 Ground Wire x 1

Pincher x 1 Spanner x 1

Note

Pincher for removing transceiver.

2.2 Power Input Port

Figure 2-2 shows the power input port side of the IGTP-825AT

Figure 2-2: IGTP-825AT Power Input port side

2.3 Data Input Port and 802.3at PoE+ Output Port

Figure 2-3 shows the “Data + PoE+” output port and “Data” input port

side of the IGTP-825AT.

PoE+ Output Data Port Input Port

Figure 2-3: IGTP-825AT RJ45 / SFP ports side

Caution

Make sure the clamping nut is tightly attached to the

cable gland body and the sealing insert is squeezed

tightly.

Step 5: “PoE (Data + Power)” Repeat Steps 1 to 4 for Output Port.

Fiber Cable Gland Installation

Step 6: Insert the SFP transceiver into the “Data” Input Port.

3. Installation

This section describes how to install the Outdoor PoE+ Media Converter

and make connections to it. Please read the following sections and

perform the procedure in the order being presented.

3.1 Installing Cable Gland with Power Cable and RJ45

UTP Cable

The cable gland consists of the following:

3.2 Connecting Waterproof Cable Kit to the Outdoor

PoE+ Media Converter

Step 1: Turn clockwise to tighten the connected to the gland body

Outdoor PoE+ Media Converter.

If any of these are missing or damaged, please contact your dealer

immediately; if possible, retain the carton including the original packing

material, and use them again to repack the product in case there is a

need to return it to us for repair.

2. Hardware Introduction

This section describes the functionalities of the Outdoor PoE+ Media

Converter’s components.

2.1 Product Outlook

Unit: mm

LNK/

ACT

PoE +Data

IGTP-825AT

LNK

PWR

DC I nput Range:

24- 56V , 2A max.

V+

Figure 2-1: IGTP-825AT product outlook

2.4 LED Indicators

LED Color Function

PWR Green Indicates it has power.

LINK/ACT Green

Lights to indicate the port is linked up at

10/100/1000Mbps.

Blinks to indicate that the IGTP-825AT is actively

sending or receiving data over that port.

LINK Green

Indicate the port is linked up at 1000Mbps and

actively sending or receiving data over that port.

To install the 2-pin Terminal Block Connector on the Outdoor PoE+

Media Converter, simply follow the following steps:

Step 1: Insert positive DC power wire into V+, negative DC power

wire into , and grounding wire into V- Ground.

V+

2-pin

Step 2: Tighten the wire-clamp screws for preventing the wires

from loosening and plug them into the Outdoor PoE+ Media

Converter.

Note

1. The wire gauge should be in the range from 20 to 22

AWG.

2. The device must be grounded.

Step 2: Plug the power cable connector into the power input port.

Step 3: sealing insert Insert the into the cable gland body.

Step 4: Attach the clamping nut to the cable gland to complete the

cable assembly.

Step 7: Thread the cable gland over the ber cable in the order as

indicated below and attach the two-hole sealing to the ber

cable.

Step 8: ConnectthebercabletotheSFPtransceiver.

Step 9: Turn clockwise to tighten the gland body.

Produkt Specifikationer

Mærke:	Planet
Kategori:	Ikke kategoriseret
Model:	IGTP-825AT
Kode for international beskyttelse (IP):	IP67
Bredde:	150 mm
Dybde:	43.8 mm
Højde:	72.94 mm
Vægt:	389 g
Produktfarve:	Black, Grey
Opbevaringstemperatur (T-T):	-40 - 85 °C
Relativ luftfugtighed ved drift (H-H):	5 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	5 - 90 %
Ethernet LAN-porte (RJ-45):	1
Driftstemperatur (T-T):	-40 - 75 °C
Husmateriale:	Aluminium, Metal
Certificering:	FCC Part 15 Class A, CE\nIEC60068-2-32 (free fall)\nIEC60068-2-27 (shock)\nIEC60068-2-6 (vibration)
LED-indikatorer:	Ja
Maksimal dataoverførselshastighed:	1000 Mbit/s
Plug and play:	Ja
Fiber optisk strømstik:	SFP
Strøm over Ethernet (PoE):	Ja
Auto MDI/MDI-X:	Ja
Auto-forhandling:	Ja