Planet IPOE-175S Manual

Planet Ikke kategoriseret IPOE-175S

Læs gratis den danske manual til Planet IPOE-175S (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 57 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 29 anmeldelser. Har du et spørgsmål om Planet IPOE-175S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

- 2 - - 4 - - 6 - - 8 -

- 1 - - 3 - - 5 - - 7 -

1. Package Contents

Thank you for purchasing PLANET Industrial IP67 802.3bt PoE++

Splitter, IPOE-175S. In the following sections, the term “Outdoor PoE

Splitter” means the IPOE-175S.

Open the box of the IPOE-175S and carefully unpack it. The box should

contain the following items:

IPOE-175S x 1 User's Manual x 1

M22 Waterproof

Cable Gland x 3

Power Cable with 2-pin

Terminal Block x 1

Wall-mounted Kit x 1 Ground Wire x 1

If any of these are missing or damaged, please contact your dealer

immediately; if possible, retain the carton including the original packing

material, and use them again to repack the product in case there is a

need to return it to us for repair.

2.2 Power Input Port

Figure 2-2 shows the Power Output port side of the IPOE-175S

Figure 2-2: Power Output Port

2.3 802.3bt PoE++ Input Port and Data Output Port

Figure 2-3 shows the Date + PoE++ Input Port and Data Output Port

side of the IPOE-175S.

PoE++ and Data

Input Port

Data Output

Figure 2-3: Two RJ45 Ports

Caution

Make sure the clamping nut is tightly attached to the

cable gland body and the sealing insert is squeezed

tightly.

Step 5: Repeat Steps 1 to 4 for “Data” output Port and “PoE (Data +

Power)” input Port.

3. Installation

This section describes how to install the Outdoor PoE Splitter and make

connections to it. Please read the following topics and perform the

procedure in the order being presented.

3.1 Installing Cable Gland with Power Cable and RJ45

UTP Cable

The cable gland consists of the following:

3.2 Connecting Waterproof Cable Kit to the Outdoor

PoE Splitter

Step 1: Turn clockwise to tighten the connected to the gland body

Outdoor PoE Splitter.

2. Hardware Introduction

This section describes the functionalities of the Outdoor PoE Splitter’s

components.

2.1 Product Outlook

Unit: mm

Ready

PoE InData

IPOE-175S

PWR

DC O ut:

12V , 5A max .

V+

Figure 2-1: IPOE-175S product outlook

2.4 LED Indicators

LED Color Function

PWR Green Indicates it has power.

DC Ready Green

Indicates the port is providing 12V DC in-line

power.

To install the 2-pin Terminal Block Connector on the Outdoor PoE

Splitter, simply follow the following steps:

Step 1: Insert positive DC power wire into V+, negative DC power

wire into , and grounding wire intoV- Ground.

V+

2-pin

Step 2: Tighten the wire-clamp screws for preventing the wires from

loosening and plug them into the Outdoor PoE Splitter

Note

1. The wire gauge should be in the range from 20 to 22

AWG.

2. The device must be grounded.

Step 2: Plug the power cable connector into the power output port.

Step 3: sealing insert Insert the into the cable gland body.

Step 4: Attach the clamping nut to the cable gland to complete the

cable assembly.

Note

1. Use only the waterproof cable gland provided in the

package of the IPOE-175S.

2. If the above installation procedure is not properly

followed, the warranty will be invalidated.

3. I the waterproof cable gland is found missing or

damage, please contact your local reseller where you

purchased from.

11.31mm

40.78mm

5.00mm

30.22mm

29.80mm

20.18

13.72

14.00

30.10

4. Never use any waterproof cable gland that is not

purchased from PLANET or doesn’t have the same

dimensions of the IPOE-175S; it will damage the device

permanently.

3.3 Wall-mount Installation

To install the Outdoor PoE Splitter on the wall, please follow the

instructions described below.

Step 1: Find the wall that you want to mount the Outdoor PoE Splitter

on.

Produkt Specifikationer

Mærke:	Planet
Kategori:	Ikke kategoriseret
Model:	IPOE-175S
Kode for international beskyttelse (IP):	IP67
Bredde:	150 mm
Dybde:	43.8 mm
Højde:	72.94 mm
Vægt:	424 g
Produktfarve:	Grå
Opbevaringstemperatur (T-T):	-40 - 85 °C
Driftstemperatur (T-T):	-40 - 75 °C
Certificering:	FCC 15 A, CE\nIEC 60068-2-32\nIEC 60068-2-27\nIEC 60068-2-6
Kabelteknologi:	10/100/1000Base-T(X)
Netværksstandarder:	IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at, IEEE 802.3bt, IEEE 802.3u
LED-indikatorer:	Power, Ready
Kan monteres på væggen:	Ja
Indgangsspænding:	44-56 V
Plug and play:	Ja
Strøm over Ethernet (PoE):	Ja
IK kode:	IK10
RJ-45 indgangs-porte:	1
RJ-45 udgangs-porte:	1