Planet IPOE-260 Series Manual

Planet Ikke kategoriseret IPOE-260 Series

Læs gratis den danske manual til Planet IPOE-260 Series (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Planet IPOE-260 Series, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET Industrial 2-port 10/100/1000T

802.3at PoE+ Injector Hub, IPOE-260/IPOE-260-12V. In the

following section, the term “Industrial PoE+ Injector Hub”

means the IPOE-260 or IPOE-260-12V.

Open the box of the Industrial PoE+ Injector Hub and carefully

unpack it. The box should contain the following items:

Industrial PoE+

Injector Hub x 1 User’s Manual x 1 Wall-mount Kit x 1

DIN-rail Kit x 1 RJ45 Dust Caps x 4

If any of these are missing or damaged, please contact your dealer

immediately.

Power

Consumption

(Ethernet Full

Loading)

Max. 2 watts/6.8 BTU

(Power on without

any connection)

Max. 80 watts/272.9

BTU (Full loading

with PoE function)

Max. 4 watts/13.6

BTU (Power on

without any

connection)

Max. 80 watts/272.9

BTU (Full loading with

PoE function)

Dimensions

(W x D x H) 30 x 70 x 105 mm

Weight 280g 280g

Enclosure IP30 metal case

Installation DIN-rail kit and wall-mount kit

ESD Protection 6KV

EFT Protection 6KV

Power over Ethernet

PoE Standard IEEE 802.3at Power over Ethernet Plus/

mid-span PSE

PoE Power Output

48V DC input: Per

PoE port max. 32

watts

56V DC input: Per

PoE port max. 36

watts

Per port 54V DC,

max. 36 watts

PoE Power Supply

Type Mid-span

Power Pin

Assignment 4/5 (+), 7/8 (-)

3.4 Wiring the Power Inputs

The terminal block connector on the top panel of Industrial PoE+

Injector Hub is used for two DC redundant power inputs. Please

follow the steps below to insert the power wire.

Caution

When performing any of the procedures like inserting

the wires or tightening the wire-clamp screws, make

sure the power is OFF to prevent from getting an

electric shock.

1. Insert positive and negative DC power wires into contacts 1 and

2 for POWER 1, or contacts 3 and 4 for POWER 2.

V1+

PWR1

V2+ V2

PWR2

DC Input:

48-56V

, 1.6A max.

1 2 3 4

2. Tighten the wire-clamp screws for preventing the wires from

loosening.

1234

Power 1 Power 2

+ - + -

3. Hardware Introduction

3.1 Switch Front Panel

The front panels of the Industrial PoE+ Injector Hubs consist of

Ethernet interfaces and LED indicators.

 Front View

P1 P2

Ethernet

802.3at PoE+

P1 P2

Ethernet

802.3at PoE+

Data port 1

PoE port 1

Data port 2

PoE port 2

Figure 1: Figure 2:

IPOE-260 Front View IPOE-260-12V Front View

2.ProductSpecications

Model IPOE-260 IPOE-260-12V

Hardware Specications

Copper Ports

2 pair 10/100/1000BASE-T RJ45 auto-MDI/

MDI-X ports:

 Data input port 1 and PoE output port 1

 Data input port 2 and PoE output port 2

Connector Removable 4-pin terminal block

Pin 1/2 for Power 1; Pin 3/4 for Power 2

LED Indicator

System:

Power 1 (Green),

Power 2 (Green),

PoE Port:

802.3at PoE+ x 2 (Green + Orange)

Network Cable

Twisted-pair cable up to 100 meters (328ft)

10BASE-T: 4-pair UTP Cat. 3, 4, 5, 5e, 6

100BASE-TX: 4-pair UTP Cat. 5, 5e, 6

1000BASE-T: 4-pair UTP Cat. 5e, 6

Data Rate 10/100/1000Mbps

Power

Requirements

48~56V DC,

redundant power

with reverse polarity

protection function.

12~56V DC,

redundant power

with reverse polarity

protection function.

PoE Power Budget

(max.)

72 watts@48~56V

DC input

60W @12~23V DC

input

72W @24~56V DC

input

Number of devices

that can be

powered

Standards Conformance

Regulatory

Compliance FCC Part 15 Class A, CE

Stability Testing

IEC 60068-2-32 (free fall)

IEC 60068-2-27 (shock)

IEC 60068-2-6 (vibration)

Standards

Compliance

IEEE 802.3 Ethernet

IEEE 802.3u Fast Ethernet

IEEE 802.3ab Gigabit Ethernet

IEEE 802.3at Power over Ethernet Plus

Environment

Temperature Operating: -40~75 degrees C

Storage: -40~75 degrees C

Humidity Operating: 5~90% (non-condensing)

Storage: 5~90% (non-condensing)

3.2 LEDDenition:

LED Color Function

P1 Green Lights to indicate power input 1 has power.

P2 Green Lights to indicate power input 2 has power.

802.3at

PoE+

PoE-in-Use

Green Lights to indicate the device is providing

PoE power to 802.3af PD.

Green +

Amber

Lights to indicate the device is providing

PoE power to 802.3at PD.

3.3 Switch Upper Panel

The upper panels of the Industrial PoE+ Injector Hubs consist of

one terminal block connector within two power inputs.

V1+

PWR1

V2+ V2

PWR2

DC Input:

48-56V

, 1.6A max.

1 2 3 4

Figure 3: IPOE-260 Top View

V1+

PWR1

V2+ V2

PWR2

DC Input:

12-56V

, 6A max.

1 2 3 4

Figure 4: IPOE-260-12V Top View

Note

The wire gauge for the terminal block should be in the

range between 12 and 24 AWG.

3.5 Grounding the Device

Users MUST complete grounding wired with the device; otherwise,

a sudden lightning could cause fatal damage to the device.

V1+

PWR1

V2+ V2

PWR2

DC Input:

48-56V

, 1.6A max.

1 2 3 4

Earth Ground

Note

EMD (Lightning) DAMAGE IS NOT CONVERED UNDER

WARRANTY.

- 9 -

- 10 -

- 11 -

- 12 - - 13 - - 14 -

4. Installation

This section guides you to installing the Industrial PoE+ Injector

Hub on the DIN rail and wall. Please read this chapter completely

before continuing.

Note

In the installation steps below, this manual uses

PLANET IGS-801 8-port Industrial Gigabit Switch as

an example. The steps for PLANET Industrial Slim-type

Switch, Industrial Media/Serial Converter and Indus-

trial PoE devices are similar.

4.1 DIN-rail Mounting Installation

4.2 Wall-mount Plate Mounting

5. Three-View Diagram

 IPOE-260

104.00

30.00

70.00

18.00

91.00

28.00

48.80

18.00

Top View

Side View Front View

Mounting Kit

DIN-Rail Kit

Side View Rear View

Unit: mm

Bottom View

P1 P2

Etherne t

802.3a t PoE+

V1+

PWR1

V2+ V2

PWR2

DC npu I t:

48-5 6V

, A 1.6 max .

Figure 5: IPOE-260 Three-View Diagram

4.3 Side Wall-mount Plate Mounting

Caution

You must use the screws supplied with the wall-

mounting brackets. Damage caused to the parts by

using incorrect screws would invalidate your warranty.

 IPOE-260-12V

104.00

30.00

70.00

18.00

91.00

28.00

48.80

18.00

Top View

Side View Front View

Mounting Kit

DIN-Rail Kit

Side View Rear View

Unit: mm

Bottom View

P1 P2

Etherne t

802.3a t PoE+

V1+

PWR1

V2+ V2

PWR2

DC npu I t:

12-5 6V

, A 6 ma x.

Figure 6: IPOE-260-12V Three-View Diagram

Customer Support

Thank you for purchasing PLANET products. You can browse our

online FAQ resource on PLANET web site rst to check if it could

solve your issue. If you need more support information, please

contact PLANET support team.

PLANET online FAQs:

http://www.planet.com.tw/en/support/faq

Support team mail address:

support@planet.com.tw

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

FCC Warning

This device has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in

a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used

in accordance with the Instruction manual, may cause harmful

interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own

expense

WEEE Warning

To avoid the potential eects on the environment and

human health as a result of the presence of hazardous

substances in electrical and electronic equipment, end

users of electrical and electronic equipment should

understand the meaning of the crossed-out wheeled bin symbol. Do

not dispose of WEEE as unsorted municipal waste and have to

collect such WEEE separately.

Produkt Specifikationer

Mærke:	Planet
Kategori:	Ikke kategoriseret
Model:	IPOE-260 Series

Har du brug for hjælp?

Hvis du har brug for hjælp til Planet IPOE-260 Series stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Planet Manualer

Planet ITS-6326-18T2XS-WV Manual

11 Juli 2025

Planet LS200-CM Manual

10 Juli 2025

Planet LS200-PM25 Manual

10 Juli 2025

Planet LS250-PLUG Manual

10 Juli 2025

Planet LS100-CO Manual

10 Juli 2025

Planet LS200-MF8 Manual

10 Juli 2025

Planet LS200-VOC Manual

10 Juli 2025

Planet ITS-6326-16P-WV Manual

10 Juli 2025

Planet IGS-4215-16P4X Manual

10 Juli 2025

Planet ITS-6326-16T-WV Manual

10 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Ikea KOPPLA 404.095.77 Manual

31 Juli 2025

Berner Architectural Elite 8 Manual

31 Juli 2025

Tripp Lite Protect It! TLP26PD30WCAM Manual

31 Juli 2025

Yealink RT20U Manual

31 Juli 2025

Tripp Lite PR60 Manual

31 Juli 2025

Advantech UTC-520J Manual

31 Juli 2025

Tripp Lite Protect It! TLM615SA Manual

31 Juli 2025

Tripp Lite SU6000XFMR2UTAA Manual

31 Juli 2025

Tripp Lite IBAR4-6D Manual

31 Juli 2025

Tripp Lite Protect It! TLP606TAA Manual

31 Juli 2025