Pyle PVNP30BT Manual

Pyle Pladespiller PVNP30BT

Læs gratis den danske manual til Pyle PVNP30BT (2 sider) i kategorien Pladespiller. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Pyle PVNP30BT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

MODEL : PVNP30BT

OPERATING INSTRUCTIONS

Please read before use

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER.

PILOT LAMPS SOLDERED IN PLACE. NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

SPECIFICATION

Frequency Range : AM:540-1700kHz (AM = MW)

: FM 88-108MHz

POWER SOURCE :

120V AC

SPEAKER OUTPUT : 1.5W

SPEAKER SIZE : 40x90mm, 8ohm 3W x 2

SPEAKER WATT :

2 x 3W

CAUTION: TO REDUCE

THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE

COVER (OR BACK). NO

USER - SERVICEABLE

PARTS INSIDE. REFER

SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The lighting flash with

arrowhead symbol, within

an equilateral triangle, is

intended to alert user to

the presence of uninsulated

"dangerous voltage" within

the product's enclosure

that may be of sufficient

magnitude to constitute

risk of electric shock

to persons.

The exclamation point

within an equilateral

triangle is intended to

alert user to the

presence of important

operating and

maintenance (servicing)

instruction in the

literature accompanying

the appliance.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

4. Phono function

Turn the “Function” Knob (1) to Phono. Place the record onto the turntable (18). Select the turntable speed

by sliding the “33/45/78 rpm” switch (23) on the right side of the turntable. Unlock the tone arm (21) by

release the lock (25), then lift up the tone arm and gently place the tone arm onto the record to play. If want

to stop, lift up the tone arm and place it back to the arm rest (25).

Re-mark:

1. If you want the turntable mechanism stop at the end of the record, select “Auto Stop” selector switch (26)

at “On” position. If the record stops playing before the end of the record, select “Auto Stop” selector switch

(24) “Off” position. The turntable mechanism will continuous to spin.

2. Place the 45rpm adaptor (19) t the centre before placing 45 rpm record onto the turntable.

5. Bluetooth function

Turn the “Function” Knob (1) to Line In. It will automatically assign to Bluetooth function and will sound. Also,

there is a Red/blue led light located at the bottom of the dial scale will flash alterively. Activate your Bluetooth

device and search for ID(Speaker) and connect. Once the unit is connected with the Bluetooth device, the

led light location on the bottom of the dial scale will flash in only blue color. Then select songs by control

your Bluetooth device.

6. Line in function

Turn the “Function” Knob (1) to Line In. It will automatically assign to Bluetooth function. Plug in the Aux-in

cable into the “Line-in Jack”(9), it will change to line-in function. Connect the other end of the Aux-in cable to

other external audio source to start playback.

7. RCA (L/R) Output Function

Using the RCA Cable to connect the RCA (L/R) output jack (28) at the rear of the unit to any external

amplifier RCA input jack to play music from external source.

Power up the unit

Insert the AC power cord (30) into the AC socket. Turn the Power On/Off Volume Knob (4) clock-wise to turn on the unit.

1. Radio/Tuner function

Turn the “Function” knob (1) to Radio, then select Am/Fm channel by sliding the “Am/Fm” slide switch (14). To select

radio station, adjust the Tuning knob (3) at the centre of the unit to select your favorite station. In order to achieve better

FM reception, extend the FM antenna (29).

2. CD function

Turn the “Function” Knob (1) to USB/CD, then press “Open/Close” button (7) to place CD into CD tray. Press again to

close the CD door. The CD Led Display will show the total number of tracks and then start to play. Press “Play/Pause”

button (6) to enter pause mode. Press “Play/Pause” button one more time to resume playback. Press “B. Skip” (13) or

“F. Skip” (15) to select your ideal track. Press “Stop” button (8) to stop playing. For repeat function, press “Repeat

button” (5) once to repeat one single track and press one more time to repeat all tracks. Press again to cancel repeat

function. To program the tracks, press “Program Button” (16), then press “B. Skip” (13) or “F.Skip” (15) button to select

your ideal track and press “Program button”. The unit can program up to 20 tracks.

Remark: Program function does not work during playback.

3. USB function

Turn the “Function” Knob (1) to USB/CD, the display will flash for CD function. Press the USB/CD button on the side of

the unit to switch to USB mode. The display will show USB for few seconds and will start playback automatically. Press

“Play/Pause” button (6) to enter pause mode. Press “Play/Pause” button one more time to resume playback. Press “B.

Skip” (13) or “F. Skip” (15) to select your ideal track. Press “Stop” button (8) to stop playing. For repeat function, press

“Repeat button” (5) once to repeat one single track and press one more time to repeat one single folder. Press again to

repeat all folders and Press again to cancel repeat function.

Location of Parts

1. Function Knob

2. Dial Scale

3. Tuning Knob

4. Power On/Off Volume Knob

5. Folder/Repeat Button

6. Play/Pause Button

7. Stop Button

8. CD Door Open/Close Button

9. 3.5mm Line-in Jack

10. CD Led Display

11. CD Door

12. Earphone Jack

13. B. Skip Button

14. Am/Fm Band Switch

15. F. Skip Button

16. Program Button

17. Turntable Shaft

18. Turntable Platter

19. 45 rpm adaptor

20. Lift Lever

21. Tone Arm

22. Cartridge

23. 33-1/3, 45 and 78 rpm selector switch

24. Auto/Manual Stop selection switch

25. Tone Arm Rest

26. Speaker

27. Air hole

28. RCA(L/R) Line-Out Jack

29. FM Antenna

30. AC cord

31. Main Power On/Off Button

IMPORTANT SAFEGUARDS FOR AUDIO PRODUCTS

PLEASE READ CAREFULLY THE FOLLOWING IMPORTANT SAFEGUARDS THAT ARE

APPLICABLE TO YOUR EQUIPMENT.

1. Read Instructions – All the safety and operating instructions should be read before the appliance

is operated.

2. Retain Instructions – The safety and operating instructions should be retained for future

reference.

3. Heed Warnings – All warnings on the appliance and in the operating

instructions should be adhered to.

4. Follow instructions – All operating and use instructions should be followed.

5. Water and Moisture – The appliance should not be used near

water-for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a

wet basement, or near swimming pool and the like.

6. Carts and Stands – The appliance should be used only with a cart or stan that is recommended

by the manufacturer.

6A. An appliance and cart combination should be moved with care. Quick stops, excessive force,

and uneven surfaces may cause the appliance and cart combination to overturn.

7. Wall or Ceiling Mounting – The appliance should be mounted to a wall or ceiling only as

recommended by the manufacturer.

8. Ventilation – The appliance should be situated so that its location or position does not interfere

with-its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or

similar surface that may block the ventilation openings; or placed in a built-in installation, such as a

bookcase or cabinet that may impede the flow of air through the ventilation openings.

9. Heat – The appliance should be situated away from heat sources such as radiators, heat

registers, stoves, or other appliances (including amplifiers) that produce heat.

10. Power Sources – The appliance should be connected to a power supply only of the type

described in the operating instructions or a marked on the appliance.

11. Grounding or Polarization – Precautions should be taken so that the grounding or polarization

means of an appliance in not impeded.

12. Power – Cord Protection – Power-supply cords should be routed so that they are not likely to be

walked on or pinched by items placed upon or against them, paying particular attention to cords at

plugs, and the point where they exit from the appliance.

13. Cleaning – The appliance should be cleaned only as recommended by the manufacturer.

14. This product is designed for use with the antenna attached and should not be connected to any

other external antennas.

15. Nonuse Periods – The power cord of the appliance should be unplugged from the outlet when

left unused for a long period of time.

16. Object and Liquid Entry – Care should be taken so objects do not fall and liquids are not spilled

into the enclosure through openings.

17. Damage Requiring Service – The appliance should be serviced by qualified service personnel

when:

A. The power-supply cord the plug has been damaged; or

B. Objects have fallen, or liquid has been spilled into the appliance; or

C. The appliance has been exposed to rain; or

D. The appliance does not appear to operate normally, or exhibits a marked change inperformance;

E. The appliance has been dropped. Or the enclosure damaged.

18. Servicing – The user should not attempt to service the appliance beyond that described in the

operating instructions. All other servicing should be referred to qualified service personnel.

Produkt Specifikationer

Mærke:	Pyle
Kategori:	Pladespiller
Model:	PVNP30BT
Type:	Direct drev pladespiller
Bredde:	376 mm
Dybde:	327 mm
Højde:	518 mm
Produktfarve:	Træ
Pakkevægt:	- g
Pakkedybde:	- mm
Pakkehøjde:	- mm
Bluetooth:	Ja
Antal højttalere:	2
Udgange til hovedtelefoner:	1
Drift:	Automatisk
Nominel hastighed:	33, 45, 78 rpm
Linie-udgang (RCA):	1
Strømforsyningstype:	Vekselstrøm
Antal indbyggede højttalere:	2
Antal USB-porte:	1
Understøttede radiobånd:	AM, FM
MP3-afspilning:	Ja
Tilslutning af hovedtelefoner:	3,5 mm
CD-afspiller:	Ja
Kanalseparation:	- dB
Automatisk stop:	Ja
Tryk fra grammafonpladenål:	- g