RAINBIRD 7005 Manual

RAINBIRD Vandingscomputer 7005

Læs gratis den danske manual til RAINBIRD 7005 (10 sider) i kategorien Vandingscomputer. Denne vejledning er vurderet som hjælpsom af 58 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 29.5 anmeldelser. Har du et spørgsmål om RAINBIRD 7005, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

Rain Bird. Conserving more than water.

® Registered trademark of Rain Bird Sprinkler Mfg. Corp.

® 2001 Rain Bird Sprinkler Corp. 5/01 P/N 250123A

Rain Bird Sales, Inc.

970 West Sierra Madre Avenue

Azusa, CA 91702 USA

Phone: (626) 963-9311

Fax: (626) 812-3411

Rain Bird Technical Services

(800) 247-3782

(U.S. and Canada only)

Rain Bird Sales, Inc.

6640 South Bonney Ave.

Tucson, AZ 85706 USA

Phone: (520) 434-6200

Fax: (520) 434-6246

Specification Hotline

(800) 458-3005

(U.S. and Canada only)

Rain Bird International, Inc.

145 North Grand Avenue

Glendora, CA 91741 USA

Phone: (626) 963-9311

Fax: (626) 963-4287

www.rainbird.com

7005 / 8005 Rotors

Operation Guide

Instrucciones de Funcionamiento

Guia de Operação

Manuel d’Instruction

Bedienungsanleitung

Istruzioni

Bedieningshandleiding

ΟHΓΙΕΣ ΧΡΗΣΗΣ

English

7005 / 8005 Rotor Operation Guide

Full/Part Circle Operation (Refer to Figure 1 on fold-out page)

All 7005/8005 rotors are factory preset to part-circle at approximately 180 degrees.

Full-Circle Operation

Insert a flat blade screwdriver into the center adjustment slot on the top of the rotor. Turn the

screwdriver clockwise so the blade is aimed toward the full-circle icon.

Part-Circle Operation

Insert a flat blade screwdriver into the center adjustment slot on the top of the rotor. Turn the

screwdriver counter clockwise so the blade is aimed toward the part-circle icon. Use the following

instructions to adjust the arc settings.

Arc Adjustment

Important facts:

• The rotor may be adjusted to any arc between 50° - 330° and full circle.

• Both right and left edges of the arc can be independently adjusted.

• One full 360 degree turn of the arc adjustment screw will change the arc edge approximately 120

degrees. Three full turns of the arc adjustment screw will rotate the trip edge completely around to

the starting point. This is significantly different than most other rotors.

• The edges of the arc cannot be felt when rotating the nozzle turret by hand. There is a light click

sound at the arc edge. If the nozzle turret is rotated past the trip point, another click may be heard.

This is the Memory Arc®function activating. No damage has occurred to the rotor. The rotor will click

once again as it is turned back into the area between the arc edges.

• The nozzle turret can be rotated by hand at any time in either direction with no damage to the rotor.

The nozzle housing may be rapid advanced by hand to speed the arc setting process.

• The arc of the rotor cannot be set to less than 50 degrees. If the 50-degree minimum is reached

during adjustment, a hard stop will be felt on the adjustment screw. To continue moving the arc edge,

move the other edge in the same direction first. Then return and continue moving the first edge. If the

adjustment screw is forced beyond the fixed stop, it will ratchet and click loudly a few times before

damage occurs.

Setting the arc - Method #1:

1. Adjust both arc edges of the rotor larger than desired.

2. To adjust the left arc edge, trip the rotor so that it is rotating counter clockwise.

3. Grip the nozzle housing to halt the rotation at the desired trip point.

4. With the rotor aimed at the desired trip point, slowly turn the left adjustment screw in the clockwise

direction until the torque of the nozzle turret is eliminated. This is a very subtle feel. The click sound

of the trip may also be heard.

5. Verify trip point during normal operation.

6. Repeat the procedure for the right side trip. The rotor must be tripped to rotate clockwise and the

right edge adjustment screw should be turned counter clockwise to reduce the arc until it trips.

Setting the arc - Method #2:

1. Determine where the edges of the arc are by rotating the nozzle turret by hand and listening for the

click sound or observe the trip during operation of the rotor.

2. Use the arc adjustment screws to increase or decrease the arc until the trip is at the desired

location.

Nozzle Installation (Refer to Figure 2 on fold-out page)

1. Insert the Pull-up Tool into the socket in the top of the rotor and twist 90 degrees. Pull the riser up to

gain access to the nozzle opening and use the hold up tool to support the riser in this extended

position.

2. Loosen the nozzle retainer screw until it no longer obstructs the nozzle opening in the nozzle

housing.

3. Using both thumbs, press the color-coded nozzle firmly into the opening until it is flush with the

nozzle turret.

4. Tighten the nozzle retainer screw. The screw threads must engage the front surface of the nozzle to

ensure proper seating of the nozzle.

5. To remove the nozzle, loosen the nozzle retainer screw and insert a flat-bladed screwdriver into the

Side Pry™ feature on the lower right edge of the nozzle to pry it loose.

Figure 1 Key

A= Part Circle Icon

B= Full/Part Circle Adjustment Slot

C= Left Edge Arc Adjustment Slot

D= Pull-up Tool Slot

E= Nozzle Retainer Screw

F= Full Circle Icon

G= Right Edge Arc Adjustment Slot

Figure 2 Key

X= Nozzle Retainer Screw Slot

Y= Pull-up Tool Slot

Z= Side Pry™ Slot

Produkt Specifikationer

Mærke:	RAINBIRD
Kategori:	Vandingscomputer
Model:	7005

Har du brug for hjælp?

Hvis du har brug for hjælp til RAINBIRD 7005 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vandingscomputer RAINBIRD Manualer

RAINBIRD ESP Modular Manual

12 August 2024

RAINBIRD RPS46 IRRIGATION CONTROLLER Manual

10 August 2024

RAINBIRD RD1800 Series Manual

9 August 2024

RAINBIRD XLR Water Jets Manual

9 August 2024

RAINBIRD Maxi-Paw Manual

8 August 2024

RAINBIRD DVF Manual

7 August 2024

RAINBIRD STPi Controller Manual

6 August 2024

RAINBIRD Falcon 6504 Manual

6 August 2024

RAINBIRD 5500 Manual

6 August 2024

RAINBIRD Image Manual

6 August 2024

Vandingscomputer Manualer

Nyeste Vandingscomputer Manualer

26 August 2024

26 August 2024

26 August 2024

26 August 2024

26 August 2024

26 August 2024

26 August 2024

26 August 2024

26 August 2024

26 August 2024