Ridgid 100A Manual

Ridgid Ikke kategoriseret 100A

Læs gratis den danske manual til Ridgid 100A (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Ridgid 100A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Universal Stands Instructions

WARNING

Read these instructions and the warn-

ings and instructions for all equipment

being used before operating this tool

to reduce the risk of serious personal

injury.

•Secure machine to the stand. This will reduce the risk of tip-

ping and serious injury.

If you have any question concerning this RIDGID ®product:

– Contact your local RIDGID distributor.

– Visit RIDGID.com to find your local RIDGID contact point.

– Contact Ridge Tool Technical Service Department at rtctech-

services@emerson.com, or in the U.S. and Canada call

(800) 519-3456.

Description

RIDGID®100A, 150A and 200A Universal Stands are used to

mount and support the 300 Compact, 535, 535A, 1224 and

1233 Threading Machines.

See the product label for specifications or consult the RIDGID cat-

alog.

Figure 1 – RIDGID 100A and 150A Stands

Assembly

1. Determine what threading machine the stand will be used

with and the required stand width:

• 535 (pre 2001), 300 Compact and 1233 - Narrow Stand

Width of 12" (30.5 cm) (535 machines made prior to 1996

require adapter bracket Cat. No. 58007)

• 535 (2001 and newer), 535A and 1224 - Wide Stand Width

of 15.5" (39.4 cm).

2. Assemble the stand, leaving the fasteners hand tight. Make

sure the “Inside” decals are towards the inside of the stand

(see Figure 2). For the Wide Stand width, use the spacers

and 4" long bolts. For the 150A and 200A, make sure that

the axles are in the forked ends of the stand stop (see

Figure 3).

3. With the stand on a smooth, level surface, securely tighten

all fasteners.

4. Carefully place the threading machine on the stand. For

150A and 200A, place the threading machines with carriage

toward the handles (see Figure 4). Align the mounting holes

in the threading machine base with the appropriate holes in

the stand, as shown in Figure 2, for proper balance. Securely

attach machine to stand.

Inspection/Maintenance

Clean the stand to aid inspection and improve control. Inspect the

stand before each use for proper assembly, wear, damage, mod-

ification or other issues that could affect safe use. If any problems

are found, do not use until corrected.

Lubricate all moving parts/joints as needed with light lubricating oil.

Wipe up excess oil.

Universal Stands Instruction Sheet

Figure 2 – Stand Parts (200A Stand shown)

Figure 3 – Stand Width (Detail Section from Figure 2)

Set Up and Operation

1. Always use the stand in clear, level, stable locations.

2. Stand leveling – Loosen nut and turn leveling pad to adjust.

Do not allow pad to come out of the leg. Tighten nut to lock

pad in place.

Transporting

1. Before moving, make sure all equipment and material is

removed from the machine and stand or properly secured to

prevent falling or tipping. Make sure the switch is in the

OFF position and the cord unplugged. The cabinet on the

200A includes slots for routing the foot switch and power cord

into the cabinet for storage.

2. The 150A and 200A wheeled stands allow threading ma -

chines to be moved over smooth, level surfaces. To use,

fully open handles and lift legs slightly off the ground before

rolling.

3. A forklift can be used to the move the threading ma-chine/ -

stands. Place the forks under the stand upper rails (just

below the threading machine) (Figure 4).

Spacer Block

4 Required

" - 16 x 4" Bolt

4 Required

Narrow Configuration

(300 Compact, 1233, 1822-I, 535 (Pre 2001))

Insert axle into stand stop ‘forked’ end.

" - 16 x 21

" Bolt

4 Required

Wide Configuration

(1224, 535A/535 Manual (2001 and after))

Insert axle into stand stop ‘forked’ end.

Cotter Pin Cotter Pin

Washer

Washer Axle

Axle

Stand Stop

Forked End

Stand Stop

Forked End

No. 100A

N° 100A

No. 100A

No. 150A

N° 150A

No. 150A

1224

(Front)

535 (Front)

300 Compact

1233, 1822

(Front)

Detail

Section

535A/535 Manual

2 001 and after

Handle

Lock Nut

Cross Member

Side Frame

Inside Sticker

Stand Stop

Leveling Pad

Printed 3/16

EC42190

244-225-066.10

REV. D

The Emerson logo and RIDGID logo are registered trademarks of Emerson Electric Co. or RIDGID, Inc. in the U.S. and other countries.

All other trademarks belong to their respective holders.

Produkt Specifikationer

Mærke:	Ridgid
Kategori:	Ikke kategoriseret
Model:	100A

Har du brug for hjælp?

Hvis du har brug for hjælp til Ridgid 100A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ridgid Manualer

28 November 2025

28 November 2025

28 November 2025

27 November 2025

25 November 2025

25 November 2025

25 November 2025

Ridgid SeeSnake RM200A Manual

25 August 2025

Ridgid SeeSnake Compact C40 DSL Manual

21 August 2025

Ridgid RB-FXP Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vevor FX-3.5-24-8 Manual

30 November 2025

Vevor CLDMFGMS01 Manual

30 November 2025

Vevor SS-door2-NA-6 Manual

30 November 2025

Vevor HNT-4in-10 Manual

30 November 2025

MDT BE-GT04W.01 Manual

30 November 2025

Blustream HDBaseT HEX11WPW-TX Manual

30 November 2025

MuxLab 500860 Manual

30 November 2025

Vevor TP2A Manual

30 November 2025

Philips BRR484 Manual

30 November 2025

Vevor CLDMFGBS02 Manual

30 November 2025