Ridgid 368 Manual

Ridgid Ikke kategoriseret 368

Læs gratis den danske manual til Ridgid 368 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Ridgid 368, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Ridge Tool Co., Elyria, Ohio, U.S.A.

9/08

Printed in U.S.A. 999-998-365.10

Pre-Cut Tube To Correct

Length

1. Add all blueprint center to center dimen-

sions for the total tube length. Mark tube at

this total length.

(Figure 1)

2. Because most blueprints are dimensioned

as though all corners were square, less

tube is actually required than the total of

the blueprint dimensions. Therefore,

REDUCE the total length by the number of

bends, using the Gain Scales on the

Swinging Arm.

(See Figure 2)

3. Reduce the measured length of tube from

Step 1 by one graduation for each 90˚ bend

using the scale marked “90˚ Gain”. Reduce

Length of tube by one graduation for each

45˚ bend using the scale marked “45˚ Gain”.

(See Figure 2)

Mark tube and cut.

Figure 1

A + B + C + D = Total Length

45˚

90˚

Swinging Arm

Rollshaft

Roll

Drive Arm

Tube

2 - 90˚ Bends

Gain

Total Length

Latch

Form

Handle

Ratchet Handle

Figure 2

Instructions For Nos. 358, 368 and 378 Tube Benders

90˚ Bends

4. For first bend, measure from end of tube

and mark at blueprint dimension.

(Figure 3)

5. Raise Latch. Bring handles together to

release Drive Arm. Swing Drive Arm counter

clockwise until it stops. Move Swinging Arm to

clear opening between Form Handle & Roll.

6. Position tube in bender.

(Figure 4a)

If the

end from which you measured is in the Form

Handle, the measured mark should be

directly under the 90˚ mark on the Drive

Arm.

(Figure 4a)

If, however, the end from

which you measured is to the right (Not in

the Form Handle), set the mark on the tube

directly under the “R” on the Drive Arm.

(Figure 4b)

7. Close Latch over tube and Swinging Arm

over Roll Shaft.

8. To Ratchet - Pull Ratchet Handle away from

Form Handle. After each pull, Drive Arm will

remain locked due to the Holding pawl.

Actuate Ratchet Handle until pointer on

Swinging Arm is at 90˚. Because tubing has

a slight springback action, it may be neces-

sary to over bend slightly to allow tube to

spring back to 90˚.

9. To release Bender, follow Step 5.

10. If more than one bend is required, measure

from center line of the preceding bent leg

and mark tube to blueprint dimension

(See

Figure 5)

. Position tube in bender as out-

lined in Step 6.

11. For convenience, the Form Handle Clamping

Pad may be held in a vise.

45˚ Bends

12. For first bend, measure from end of tube

and mark at blueprint dimension.

13. Position tube in bender, as illustrated in

Figure 4 a-b

. When making a 45˚ bend, the

end from which you measured and marked

the tube may be either in the Form Handle

or to the right (Not in the Form Handle). In

either case, the mark on the tube should be

under the 45˚ mark on the Drive Arm.

14. Close Latch over tube. Move Swinging Arm

to engage Roll Shaft.

15. To Bend - Follow Step 8 until pointer on

Swinging Arm is at 45˚.

Ridge Tool Co., Elyria, Ohio, U.S.A.

Figure 3

Figure 4a

Latch Drive Arm Mark

Tube

Form

Handle

Ratchet

Handle

Figure 4b

Latch Drive Arm Mark

Tube

Form

Handle

Ratchet

Handle

Figure 5

Instructions For Nos. 358, 368 and 378 Tube Benders

Produkt Specifikationer

Mærke:	Ridgid
Kategori:	Ikke kategoriseret
Model:	368

Har du brug for hjælp?

Hvis du har brug for hjælp til Ridgid 368 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ridgid Manualer

16 August 2025

26 Juli 2025

19 Juni 2025

19 Juni 2025

Ridgid 300 Compact Manual

12 Januar 2025

Ridgid K-750 Manual

12 Januar 2025

Ridgid HKO-186 Manual

31 August 2024

Ridgid Raprench 10 Manual

31 August 2024

Ridgid KT-190 Manual

31 August 2024

Ridgid 760 FXP Manual

30 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

YSI T-1 Manual

16 August 2025

Extron HC 403 Manual

16 August 2025

Advantech DS-082 Manual

16 August 2025

Pentatech KA20 Manual

16 August 2025

Advantech WOP-215K-NAE Manual

16 August 2025

Emerson CKSS7801WM Manual

16 August 2025

MSW -FMP-01 Manual

16 August 2025

Vulcan VICM24 Manual

16 August 2025

HP Elite Mini 805 G8 Manual

16 August 2025

TP-Link LS106P Manual

16 August 2025