Ridgid 405/408M Manual

Ridgid Ikke kategoriseret 405/408M

Læs gratis den danske manual til Ridgid 405/408M (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Ridgid 405/408M, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

300 and 400 Lever Bender Instruction Sheet

Inspection/Maintenance

The bender should be inspected before each use for wear or dam-

age that could affect safe use. Clean as needed to aid inspection

and to prevent handles and controls from slipping from your grip

during use.

Make sure the bender is complete and properly assembled. If any

problems are found, do not use until the problems are corrected.

Lubricate all moving parts/joints as needed with a light lubricating

oil, and wipe any excess oil from the bender.

Operation

The benders can be used either hand held or mounted in a vise. See

Figures 1 & 2 for area to be securely gripped in vise.

Spring Back

All tubing will spring back slightly after a bend is made. Amount

of spring back depends on tube characteristics. You may need to

slightly overbend the tube to compensate for spring back.

General Operation

1. Rotate the form handle and latch out of the way.

2. Position tube in form groove

and secure with the latch. At

least 1/8" (3 mm) of tube should

extend past the latch.

3. Rotate shoe insert into contact

with tube. Rotate the shoe

handle around the form until

the “0” line on the shoe insert

aligns with the desired degree

of bend on the form.

For 90° and 45° Bends:

Mark the tube at the desired distance (X) from the feature (end

of tube, bend, etc.). The center of the leg of the bend will be this

distance from the feature for 90° bends. The center of the arc will

be this distance from the feature for 45° bends.

Align the tube in the form.

a. For 90° Bends:

If the feature is to the of the mark, align the mark with the LEFT

90° line on the form.

Figure 4A – Aligning for 90° Bend (LEFT)

If the feature is to the of the mark, align the mark with the RIGHT

R line on the form.

Figure 4B – Aligning for 90° Bend (RIGHT)

300 and 400 Lever Bender

Instructions

WARNING

Read these instructions and the warn-

ings and instructions for all equipment

being used before using to reduce the

risk of serious personal injury.

• Always use safety glasses to reduce the risk of eye injury.

• Do not use handle extensions (such as a piece of pipe).

Han dle extensions can slip or come off and increase the

risk of serious injury.

If you have any question concerning this RIDGID® product:

– Contact your local RIDGID distributor.

– Visit RIDGID.com or to find your local RIDGID contact point.

– Contact Ridge Tool Technical Service Department at

ProToolsTechService@Emerson.com, or in the U.S. and Canada

call 844-789-8665.

Selection of appropriate materials and installation, joining

and forming methods is the responsibility of the system designer

and/or installer. Selection of improper materials and methods could

cause system failure.

Stainless steel and other corrosion resistant materials can be con-

taminated during installation, joining and forming. This contamination

could cause corrosion and premature failure. Careful evaluation of

materials and methods for the specific service conditions, including

chemical and temperature, should be completed before any instal-

lation is attempted.

Description

The RIDGID® 300 and 400 Series Lever Benders are designed to

easily bend metal tubes to a maximum of 180°. The benders have

offset cushion grip handles and 90° start angle with specially de-

signed shoe to minimize bending efforts.

The 300 Series Plumbing benders are used to bend soft copper

tubes. The 400 Series Instrument benders can be used to bend

copper, steel and stainless steel tubes with a wall thickness up to

0.06" (1,5 mm).

See RIDGID catalog for specifications for each bender.

Figure 1 – 300 Series Plumbing Bender

Figure 2 – 400 Series Plumbing Bender

Shoe Handle

Form Model Number Location

NOTICE

Latch

Shoe Insert

Mark On

Tube

90° Line

on Form

Form Handle

Vise Clamp Block

Shoe Handle

Shoe

Insert

Form

Latch

Model Number Location

Vise Clamp Block

Figure 3 – Positioning Tube in

Bender

Before After

Mark On

Tube

R Line

Printed 11/22

890-011-232.09

ECN001818

REV. B

RIDGID and the Emerson logo are registered trademarks of Emerson Electric Co. or its subsidiaries in the US and other countries.

Any other trademarks belong to their respective holders.

Produkt Specifikationer

Mærke:	Ridgid
Kategori:	Ikke kategoriseret
Model:	405/408M

Har du brug for hjælp?

Hvis du har brug for hjælp til Ridgid 405/408M stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ridgid Manualer

28 November 2025

28 November 2025

28 November 2025

27 November 2025

25 November 2025

25 November 2025

25 November 2025

Ridgid SeeSnake RM200A Manual

25 August 2025

Ridgid SeeSnake Compact C40 DSL Manual

21 August 2025

Ridgid RB-FXP Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vevor FX-3.5-24-8 Manual

30 November 2025

Vevor CLDMFGMS01 Manual

30 November 2025

Vevor SS-door2-NA-6 Manual

30 November 2025

Vevor HNT-4in-10 Manual

30 November 2025

MDT BE-GT04W.01 Manual

30 November 2025

Blustream HDBaseT HEX11WPW-TX Manual

30 November 2025

MuxLab 500860 Manual

30 November 2025

Vevor TP2A Manual

30 November 2025

Philips BRR484 Manual

30 November 2025

Vevor CLDMFGBS02 Manual

30 November 2025