Ridgid 456 Manual

Ridgid Ikke kategoriseret 456

Læs gratis den danske manual til Ridgid 456 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Ridgid 456, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

La cintreuse 456 Tri-Bender sert au cintrage des tubes recuits Ø 1/4",

5/16" et 3/8".

Le port systématique de lunettes de sécurité s’im-

pose afin de limiter les risques de blessure oculaire.

Utilisation générale

1. Relevez la poignée de cintrage afin de positionner le tube dans la

rainure appropriée de la poignée à galet. Assurez-vous que le tube

s’engage bien dans la bride

(Figure 1)

2. Rabattez la poignée de cintrage jusqu’au tube, puis fermez-la contre

la poignée de gabarit jusqu’à ce que le repère « 0 » de la poignée

de cintrage s’aligne sur le repère d’angle de cintrage approprié de la

poignée à galet

(Figure 2)

Figure 1 Figure 2

Repérage de l’axe de cintrage par

rapport à un élément donné (embout

de tuyau, coude, etc.)

Coudes à 90°

• Repérez l’axe de cintrage (X) en marquant le tube à la distance

voulue d’un élément existant (embout de tuyau, coude, etc.). Ceci

donnera l’axe de la partie coudée du tuyau.

• Positionnez le tube dans la cintreuse comme indiqué à

l’article 1

• Si l’élément existant se trouve à la du repère tracé sur le tubegauche

(Figure 3 – Avant)

, alignez le repère sur la ligne « L» de la poignée

de cintrage.

• Si l’élément existant se trouve à la droite du repère tracé sur le tube

(Figure 4 – Avant)

, alignez le repère sur la ligne « » de la poignéeR

de cintrage.

Figure 3 – Avant (Before) Figure 3 – Après (After)

Ridge Tool Company/Elyria, Ohio, U.S.A.

6/09

Printed in U.S.A. 999-998-655.10

456 Tri-Bender Instruction Sheet

• Align the mark on the tube with the unlabeled line on the shoe han-

dle

(see Figure 5)

Figure 5 – Before Figure 5 – After

• With the mark on the tube appropriately aligned, move the shoe

handle so that the “0” line aligns with the 45 degree line on the form

handle.

If you have any question concerning this Ridge Tool product:

• Contact your local RIDGID distributor.

• Visit www.RIDGID.com or www.RIDGID.eu to find your local Ridge

Tool contact point.

• Contact Ridge Tool Technical Services Department at techser-

vices@ridgid.com, or in the U.S. and Canada call (800) 519-3456.

The 456 TR-Bender is used to bend 1/4", 5/16" and 3

/8" soft tubing.

Always wear safety glasses to reduce the risk of eye

injury.

General Use

1. Rotate the shoe handle out of the way and position the tube in the

appropriate groove in the form handle. Be sure that the tube

engages the tube latch

(Figure 1).

2. Rotate the shoe handle into contact with the tube, and rotate the

shoe handle around the form handle so that the “0” line on the

shoe handle aligns with the desired degree of bend on the form

handle

(Figure 2)

Figure 1 Figure 2

Measured Bends Relative to Other

Features (Tube ends, Bends, etc.)

For 90° Bends:

• Mark the tube at the desired distance (X) from the feature (end of

tube, bend, etc.). The center of the leg of the bend will be this dis-

tance from the feature.

• Place the tube in the bender as described in

Step 1

above.

• If the feature is to the LEFT of the mark

(see Figure 3 – Before),

align the mark on the tube with the “ ” line on the shoe handle.L

• If the feature is to the RIGHT of the mark

(see Figure 4 – Before)

align the mark on the tube with the “ ” line on the shoe handle.R

Figure 3 – Before Figure 3 – After

Figure 4 – Before Figure 4 – After

• With the mark on the tube appropriately aligned, move the shoe

handle so that the “0” line aligns with the 90 degree line on the form

handle.

(See Figures 3 and 4 – After).

For 45° Bends:

• Mark the tube at the desired distance (X) from the feature (end of

tube, bend, etc.). The center of the arc segment will be this distance

from the feature.

• Place the tube in the bender as described in

Step 1

above.

Shoe

Handle

Tube

Latch

Form

Handle

Mark On

Tube

Mark On

Tube

L Line

R Line

Mark On

Tube

XUnlabeled

Line X

WARNING

Cintreuse 456 Tri-Bender : Mode d’emploi

AVERTISSEMENT

Shoe Handle – Poignée de cintrage

Tube Latch – Bride

Form Handle – Poignée à galet

L Line – Ligne L

Mark On Tube – Repère du tube

Produkt Specifikationer

Mærke:	Ridgid
Kategori:	Ikke kategoriseret
Model:	456

Har du brug for hjælp?

Hvis du har brug for hjælp til Ridgid 456 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ridgid Manualer

16 August 2025

26 Juli 2025

19 Juni 2025

19 Juni 2025

Ridgid 300 Compact Manual

12 Januar 2025

Ridgid K-750 Manual

12 Januar 2025

Ridgid HKO-186 Manual

31 August 2024

Ridgid Raprench 10 Manual

31 August 2024

Ridgid KT-190 Manual

31 August 2024

Ridgid 760 FXP Manual

30 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Alpine IVA-C800R Manual

17 August 2025

ZyXEL XGS1935-28 Manual

17 August 2025

Alpine TUE-T200DVB Manual

17 August 2025

Royal Catering RC-SGI01 Manual

17 August 2025

Crelando HG06256E Manual

17 August 2025

Nabo FK 2570 Manual

17 August 2025

Primo PR164RKZ Manual

17 August 2025

IFM CR1142 Manual

17 August 2025

Hartke Bass Attack 2 Manual

17 August 2025

Ferroli TP3 COND 65÷1000 Manual

16 August 2025