Ridgid 461 Manual

Ridgid Ikke kategoriseret 461

Læs gratis den danske manual til Ridgid 461 (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Ridgid 461, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

Pipe Vise User Guide

WARNING

Read the warnings and instructions

for all equipment and material being

used before operating this tool to

reduce the risk of serious personal

injury.

•Properly support the vise and pipe. Failure to properly sup-

port the equipment can cause vise tipping, falling pipe, chain

breakage and serious injury.

• Use appropriate safety equipment. Always wear proper eye

and foot protection to reduce the risk of injury.

• Do not use handle extensions (“cheaters”) or excessive

force. These may damage the tool or cause serious injury.

Selection of appropriate materials and installation, join-

ing and forming methods is the responsibility of the system designer

and/or installer. Selection of improper materials and methods could

cause system failure.

Stainless steel and other corrosion resistant materials can be

con taminated during installation, joining and forming. This contam-

ination could cause corrosion and premature failure. Care ful evalu-

ation of materials and methods for the specific service conditions,

including chemical and temperature, should be completed before

any installation is attempted.

If you have any question concerning this RIDGID ® product:

– Contact your local RIDGID distributor.

– Visit RIDGID.com to find your local RIDGID contact point.

– Contact Ridge Tool Technical Service Department at rtctech-

services@emerson.com, or in the U.S. and Canada call (800)

519-3456.

Description

RIDGID® Pipe Vises use a chain or yoke vise to hold and work pipe.

Many Pipe Vises include features to allow pipe bending.

The bench vises are mounted to a bench or other stable horizontal

platform. For lighter duty applications, portable vises are equipped

with a clamp or chain for temporary mounting. Vises/jaws are avail-

able for use with plastic pipe.

See the product label for specifications or consult the RIDGID

catalog.

Figure 1 – RIDGID Pipe Vises

Pipe Vise User Guide

Inspection/Maintenance

Clean the vise to aid inspection and improve control. Inspect the vise

before each use for proper assembly, wear, damage, modification

or other issues that could affect safe use. Clean the jaws with a wire

brush. Replace jaws if teeth are worn to prevent pipe slippage. If any

problems are found, do not use until corrected.

For chain vises, inspect the chain for separation of the links or any

other damage. Link separation indicates the chain has been over-

stressed and should be replaced. Use only identical replacement

parts from RIDGID when servicing.

Confirm that the mounting fasteners are secure.

Lubricate all moving parts/joints as needed with light lubricating oil.

Wipe up excess oil.

Set Up/Operation

1. Make sure all equipment is inspected and set up per its instruc-

tions.

2. Assemble the Yoke Vise:

a. Place the yoke on base with hook orientation as required,

left or right side (Figure 2).

b. Insert Hinge Bolt through yoke and base assembly. Assem-

ble washer and nut to Hinge Bolt, and then tighten. If yoke

does not swing freely on base, tap threaded end of Hinge

Bolt with hammer.

Figure 2 – Yoke Vise Assembly

3. Choose a level, stable location to mount the vise. Loca tion

must be able to support the working loads applied to the pipe/

vise without bending, breaking, moving, tipping or other issues.

Material may need to be added to allow proper mounting

(wood or metal backing). Make sure there is nothing that will

be damaged by mounting the vise (electrical wires, etc.).

4. Pipe vises are usually located along the edge of benches.

Chain vises overhang the edge and have stops that locate the

vise relative to the bench edge.

a. Bench Vises: Use the holes in the vise base as a template

for locating the holes in the bench. Use the largest diameter

fastener that will fit in the vise and spool holes. Use appro-

priate grade fasteners for the installation. Use through bolts

with washers and locking nuts/wash ers. Bolts go through the

bending spools. See the vise parts list for more information.

Do not weld the vise in place. The vise bases are not

designed to be welded to.

b. Portable Yoke Vise: Securely clamp the vise to the platform

by tightening the clamp screw assembly (Figure 1C).

c. Portable Chain Vise: Hold the vise near a stable vertical

post/pipe. Wrap the coin chain around post and hook the

chain pin in the base groove. Securely tighten the chain

around post by rotating the eye bolt with handle (Figure 1D).

Confirm that the vise is secure and stable.

5. Carefully place the pipe on vise. Do not drop the pipe on the

vise. For best stability during use, keep the pipe end to be

worked on as close to the vise as possible.

6. Use appropriate pipe supports if the pipe extends past the base

of the vise.

Place stands to properly support long pipes. Generally pipe

should be supported in at least two places. The number and

A. Bench Chain Vise

C. Portable Yoke Vise D. Portable Chain Vise

Clamp

Screw

Assembly

Base

B. Bench Yoke Vise

Yoke

HandleLink

Chain

Coin Chain

NOTICE

Hook

Handle

Link Chain

Printed 7/18

EC42887

999-888-102.10

REV. A

The Emerson logo and RIDGID logo are registered trademarks of Emerson Electric Co. or RIDGID, Inc. in the U.S. and other countries.

All other trademarks belong to their respective holders.

Pipe Vise User Guide

placement of stands depend on the specific circumstances,

including pipe size, length and weight.

Make sure that the pipe is properly centered on the vise and

stands to reduce the risk of tipping. Do not exceed the vise

ratings. Make sure pipe is stable and secure. Always stay clear

of supported loads.

7. Secure the pipe on vise. The work piece should extend across

the entire lower jaw. Do not grip the work piece at the very end.

This will ensure a secure grip and prevent vise damage.

a. Chain Vise: Place the chain over the pipe and hook the

chain pin in the base groove. Tighten the chain by rotating

the handle to grip the pipe.

b. Yoke Vise: Lift the hook and swing the yoke to the side to

open the Vise. Place the pipe on the Lower Jaw. Close the

yoke, making sure the hook is engaged with the vise base.

Close the jaws by turning the feed screw to grip the pipe.

Do not use handle extensions (“Cheaters”) to tighten the vise.

Do not hammer on the handles. This can overload the vise and

cause damage to the vise or the work piece.

8. Make sure the pipe and vise are stable for the work to be done.

When using the vise, do not overreach and maintain proper

footing and balance at all times. This allows better control in

unexpected situations.

Do not apply extreme or prolonged heat to the workpiece – this

could overheat the vise and alter the vise material properties.

9. Pipe Bending:

Place the pipe as shown for bending. Make sure the end of the

pipe is far enough from the support points to prevent slippage

and pipe damage. Apply gradual force on the pipe to bend the

pipe.

A) Bench Chain Vise

B) Bench Yoke Vise

Figure 3 – Bending Pipe

To reduce the risk of kinking, bend the pipe approximately

10 degrees at a time, moving the pipe slightly in or out of the

bending spools until the desired bend is formed.

Mode d’emploi des étaux à tuyaux

AVERTISSEMENT

Afin de limiter les risques d’accident

grave, familiarisez-vous avec les aver-

tissements et consignes d’utilisation de

l’ensemble du matériel et des matériaux

utilisés avant de manipuler cet outil.

•Soutenez à la fois l’étau et le tuyau de manière appro-

priée. Du matériel mal soutenu risque d’occasionner le ren-

versement de l’étau, la chute du tuyau, la rupture de la chaîne

et de graves blessures corporelles.

• Prévoyez les équipements de protection appropriés. Afin

de limiter les risques de blessure, portez systématiquement une

protection oculaire adéquate et des chaussures de sécurité.

• Ne jamais utiliser de rallonge de manche ou de force

excessive. Celles-ci peuvent endommager l’outil ou provoquer

de graves blessures corporelles.

Le choix des matériaux, des techniques d’in-

stallation et des méthodes de raccordement utilisés restent la

responsabilité du bureau d’études et/ou de l’installateur. La sélection

de matériaux et de méthodes inappropriés pourrait provoquer la

défaillance du réseau.

L’acier inoxydable et autres matériaux anticorrosion risquent d’être

contaminés en cours d’installation, de raccordement et de façon-

nage. Une telle contamination pourrait provoquer la corrosion et la

défaillance prématurée des éléments. Avant toute tentative d’in-

stallation, il convient d’effectuer une étude approfondie des matéri-

aux et méthodes utilisés en fonction des conditions d’exploitation

envisagées, notamment au niveau de la composition chimique et

température du réseau.

En cas de questions visant ce produit RIDGID ® veuillez :

– Consulter le revendeur RIDGID le plus proche.

– Visiter le site RIDGID.com pour localiser le représentant RIDGID

le plus proche.

– Consulter les services techniques de Ridge Tool par courriel

adressé à rtctechservices@emerson.com, ou bien, à partir des

Etats-Unis ou du Canada, en composant le (800) 519-3456.

Description

Les étaux à tuyaux RIDGID® utilisent une chaîne ou une bride pour

arrimer les tuyaux. De nombreux étaux à tuyaux sont également

équipés de dispositifs permettant le cintrage des tuyaux.

Les étaux d’établi se montent sur établi ou autre surface horizontale

stable. Les étaux portables sont équipés d’une chaine ou d’un serre-

joint pour les montages temporaires légers. Des mâchoires d’étau

pour tuyaux en matière plastique sont également disponibles.

Reportez-vous à la plaque signalétique du produit ou consultez le

catalogue RIDGID pour les caractéristiques correspondantes.

Figure 1 – Etaux à tuyaux RIDGID

Inspection et entretien

Nettoyez l’étau afin d’en faciliter l’inspection et améliorer sa manip-

ulation. Examinez l’étau avant chaque intervention pour un assem-

A. Etau d’établi à chaîne

Embase

B. Etau d’établi à bride

Bride

Poignée

Chaîne à

rouleaux

AVIS IMPORTANT

Crochet

C. Etau portable à bride D. Etau portable à chaînes

Vis de

serre-joint Chaine en

mailles

Poignée

Chaîne à

maillons

Produkt Specifikationer

Mærke:	Ridgid
Kategori:	Ikke kategoriseret
Model:	461

Har du brug for hjælp?

Hvis du har brug for hjælp til Ridgid 461 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ridgid Manualer

16 August 2025

26 Juli 2025

19 Juni 2025

19 Juni 2025

Ridgid 300 Compact Manual

12 Januar 2025

Ridgid K-750 Manual

12 Januar 2025

Ridgid HKO-186 Manual

31 August 2024

Ridgid Raprench 10 Manual

31 August 2024

Ridgid KT-190 Manual

31 August 2024

Ridgid 760 FXP Manual

30 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vulcan VICM24 Manual

16 August 2025

HP Elite Mini 805 G8 Manual

16 August 2025

TP-Link LS106P Manual

16 August 2025

ATen CL1308 Manual

16 August 2025

Testboy Light 400 Manual

16 August 2025

Vulcan VIR1F Manual

16 August 2025

HP Poly Studio X72 Manual

16 August 2025

Supermicro X14DBM-AP Manual

16 August 2025

ZyXEL XGS1935-28HP Manual

16 August 2025

Supermicro A4SAN-H Manual

16 August 2025