Ridgid 606 Manual

Ridgid Ikke kategoriseret 606

Læs gratis den danske manual til Ridgid 606 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Ridgid 606, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

600 Hand Tube Bender Instruction Sheet

Figure 2 – Vise Mounting Point Figure 3

2. Move Carriage Handle and Tube Latch away from Form.

3. Position tubing in Form groove and secure tubing in Form with

Latch (Figure 3).

4. Lower Carriage Handle until the “0” Line on the Carriage aligns with

the 0° designation on the Form (Figure 4).

5. Rotate the Carriage Handle around the Form until the “0” Line on the

Carriage aligns with the desired degree of bend on the Form (Figure

5).

Figure 4 Figure 5

Measured Bends Relative to Other

Features (Tube ends, Bends, etc.)

For 90° Bends:

• Mark the tube at the desired distance (X) from the feature (end of

tube, bend, etc.). The center of the leg of the bend will be this dis-

tance from the feature.

• Place the tube in the bender as described in Steps 1-5 above.

• If the feature is to the of the mark LEFT (see Figure 6 – Before),

align the mark on the tube with the “ ” line on the Carriage.L

• If the feature is to the of the mark RIGHT (see Figure 8 – Before),

align the mark on the tube with the “ ” line on the Carriage.R

Figure 6 – Before Figure 7 – After

Figure 8 – Before Figure 9 – After

• With the mark on the tube appropriately aligned, move the Carriage

so that the “0” Line aligns with the 90 degree line on the Form. (See

Figures 7 and 9 – After).

WARNING

Read these instructions and the warnings and

instructions for all equipment being used before

using to reduce the risk of serious personal injury.

• Always use safety glasses to reduce the risk of

eye injury.

• Do not use handle extensions (such as a piece

of pipe). Han dle extensions can slip or come off and increase

the risk of serious injury.

If you have any question concerning this RIDGID®product:

– Contact your local RIDGID distributor.

– Visit www.RIDGID.com or www.RIDGID.eu to find your local RIDGID

contact point.

– Contact Ridge Tool Technical Service Department at rtctechservic -

es@em erson.com, or in the U.S. and Canada call (800) 519-3456.

The RIDGID®600 series lever benders are designed to easily bend

materials such as copper, steel, stainless steel and other hard metal

tube to a maximum of 180°. Built-in rollers and a heavy-duty handle

design combine to produce high quality bends with greatly reduced

effort when compared to conventional benders.

Figure 1 – 600 Series Bender

Selection of appropriate materials and installation, joining

and forming methods is the responsibility of the system designer and/or

installer. Selection of improper materials and methods could cause sys-

tem failure.

Stainless steel and other corrosion resistant materials can be contami-

nated during installation, joining and forming. This contamination could

cause corrosion and premature failure. Careful evaluation of materials

and methods for the specific service conditions, including chemical and

temperature, should be completed before any installation is attempted.

Inspection/Maintenance

The bender should be inspected before each use for wear or damage

that could affect safe use. Clean as needed to aid inspection and to pre-

vent handles and controls from slipping from your grip during use.

Make sure the bender is complete and properly assembled. If any prob-

lems are found, do not use until the problems are corrected. Lubricate

all moving parts/joints as needed with a light lubricating oil, and wipe

any excess oil from the bender.

Operation

The 600 Series Lever Benders can be used either hand held or with the

bender mounted in a vise. Vise mounting is especially useful when

bending hard or thick walled materials.

Spring Back

All tubing will exhibit spring back after a bend is completed. Softer tub-

ing, such as copper, will have less spring back than harder tubing, such

as stainless steel. Experience will help you predict the amount of spring

back. Depending on tubing material and hardness, expect to overbend

approximately 1° to 3° to compensate for spring back.

General Operating Instruction

1. Grasp bender by the Form Handle or mount the bender in vise.

(Figure 2).

Carriage Handle

Tube

Latch

Form Handle

NOTICE

Form

Carriage

Grip In

Vise

Mark On

Tube

L Line

0 Line

Mark On

Tube

R Line

Printed 12/15

EC38632

999-999-403.10

REV. C

The Emerson logo and RIDGID logo are registered trademarks of Emerson Electric Co. or RIDGID, Inc. in the U.S. and other countries.

All other trademarks belong to their respective holders.

Produkt Specifikationer

Mærke:	Ridgid
Kategori:	Ikke kategoriseret
Model:	606

Har du brug for hjælp?

Hvis du har brug for hjælp til Ridgid 606 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ridgid Manualer

28 November 2025

28 November 2025

28 November 2025

27 November 2025

25 November 2025

25 November 2025

25 November 2025

Ridgid SeeSnake RM200A Manual

25 August 2025

Ridgid SeeSnake Compact C40 DSL Manual

21 August 2025

Ridgid RB-FXP Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vevor FX-3.5-24-8 Manual

30 November 2025

Vevor CLDMFGMS01 Manual

30 November 2025

Vevor SS-door2-NA-6 Manual

30 November 2025

Vevor HNT-4in-10 Manual

30 November 2025

MDT BE-GT04W.01 Manual

30 November 2025

Blustream HDBaseT HEX11WPW-TX Manual

30 November 2025

MuxLab 500860 Manual

30 November 2025

Vevor TP2A Manual

30 November 2025

Philips BRR484 Manual

30 November 2025

Vevor CLDMFGBS02 Manual

30 November 2025