Ridgid 640 Manual

Ridgid Ikke kategoriseret 640

Læs gratis den danske manual til Ridgid 640 (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Ridgid 640, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

Pipe Vise User Guide

WARNING

Read the warnings and instructions

for all equipment and material being

used before operating this tool to

reduce the risk of serious personal

injury.

•Properly support the vise and pipe. Failure to properly sup-

port the equipment can cause vise tipping, falling pipe, chain

breakage and serious injury.

• Use appropriate safety equipment. Always wear proper eye

and foot protection to reduce the risk of injury.

• Do not use handle extensions (“cheaters”) or excessive

force. These may damage the tool or cause serious injury.

Selection of appropriate materials and installation, join-

ing and forming methods is the responsibility of the system designer

and/or installer. Selection of improper materials and methods could

cause system failure.

Stainless steel and other corrosion resistant materials can be

con taminated during installation, joining and forming. This contam-

ination could cause corrosion and premature failure. Care ful evalu-

ation of materials and methods for the specific service conditions,

including chemical and temperature, should be completed before

any installation is attempted.

If you have any question concerning this RIDGID ® product:

– Contact your local RIDGID distributor.

– Visit RIDGID.com to find your local RIDGID contact point.

– Contact Ridge Tool Technical Service Department at rtctech-

services@emerson.com, or in the U.S. and Canada call (800)

519-3456.

Description

RIDGID® Pipe Vises use a chain or yoke vise to hold and work pipe.

Many Pipe Vises include features to allow pipe bending.

The bench vises are mounted to a bench or other stable horizontal

platform. For lighter duty applications, portable vises are equipped

with a clamp or chain for temporary mounting. Vises/jaws are avail-

able for use with plastic pipe.

See the product label for specifications or consult the RIDGID

catalog.

Figure 1 – RIDGID Pipe Vises

Pipe Vise User Guide

Inspection/Maintenance

Clean the vise to aid inspection and improve control. Inspect the vise

before each use for proper assembly, wear, damage, modification

or other issues that could affect safe use. Clean the jaws with a wire

brush. Replace jaws if teeth are worn to prevent pipe slippage. If any

problems are found, do not use until corrected.

For chain vises, inspect the chain for separation of the links or any

other damage. Link separation indicates the chain has been over-

stressed and should be replaced. Use only identical replacement

parts from RIDGID when servicing.

Confirm that the mounting fasteners are secure.

Lubricate all moving parts/joints as needed with light lubricating oil.

Wipe up excess oil.

Set Up/Operation

1. Make sure all equipment is inspected and set up per its instruc-

tions.

2. Assemble the Yoke Vise:

a. Place the yoke on base with hook orientation as required,

left or right side (Figure 2).

b. Insert Hinge Bolt through yoke and base assembly. Assem-

ble washer and nut to Hinge Bolt, and then tighten. If yoke

does not swing freely on base, tap threaded end of Hinge

Bolt with hammer.

Figure 2 – Yoke Vise Assembly

3. Choose a level, stable location to mount the vise. Loca tion

must be able to support the working loads applied to the pipe/

vise without bending, breaking, moving, tipping or other issues.

Material may need to be added to allow proper mounting

(wood or metal backing). Make sure there is nothing that will

be damaged by mounting the vise (electrical wires, etc.).

4. Pipe vises are usually located along the edge of benches.

Chain vises overhang the edge and have stops that locate the

vise relative to the bench edge.

a. Bench Vises: Use the holes in the vise base as a template

for locating the holes in the bench. Use the largest diameter

fastener that will fit in the vise and spool holes. Use appro-

priate grade fasteners for the installation. Use through bolts

with washers and locking nuts/wash ers. Bolts go through the

bending spools. See the vise parts list for more information.

Do not weld the vise in place. The vise bases are not

designed to be welded to.

b. Portable Yoke Vise: Securely clamp the vise to the platform

by tightening the clamp screw assembly (Figure 1C).

c. Portable Chain Vise: Hold the vise near a stable vertical

post/pipe. Wrap the coin chain around post and hook the

chain pin in the base groove. Securely tighten the chain

around post by rotating the eye bolt with handle (Figure 1D).

Confirm that the vise is secure and stable.

5. Carefully place the pipe on vise. Do not drop the pipe on the

vise. For best stability during use, keep the pipe end to be

worked on as close to the vise as possible.

6. Use appropriate pipe supports if the pipe extends past the base

of the vise.

Place stands to properly support long pipes. Generally pipe

should be supported in at least two places. The number and

A. Bench Chain Vise

C. Portable Yoke Vise D. Portable Chain Vise

Clamp

Screw

Assembly

Base

B. Bench Yoke Vise

Yoke

HandleLink

Chain

Coin Chain

NOTICE

Hook

Handle

Link Chain

Printed 7/18

EC42887

999-888-102.10

REV. A

The Emerson logo and RIDGID logo are registered trademarks of Emerson Electric Co. or RIDGID, Inc. in the U.S. and other countries.

All other trademarks belong to their respective holders.

Produkt Specifikationer

Mærke:	Ridgid
Kategori:	Ikke kategoriseret
Model:	640

Har du brug for hjælp?

Hvis du har brug for hjælp til Ridgid 640 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ridgid Manualer

28 November 2025

28 November 2025

28 November 2025

27 November 2025

25 November 2025

25 November 2025

25 November 2025

Ridgid SeeSnake RM200A Manual

25 August 2025

Ridgid SeeSnake Compact C40 DSL Manual

21 August 2025

Ridgid RB-FXP Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vevor FX-3.5-24-8 Manual

30 November 2025

Vevor CLDMFGMS01 Manual

30 November 2025

Vevor SS-door2-NA-6 Manual

30 November 2025

Vevor HNT-4in-10 Manual

30 November 2025

MDT BE-GT04W.01 Manual

30 November 2025

Blustream HDBaseT HEX11WPW-TX Manual

30 November 2025

MuxLab 500860 Manual

30 November 2025

Vevor TP2A Manual

30 November 2025

Philips BRR484 Manual

30 November 2025

Vevor CLDMFGBS02 Manual

30 November 2025