Ridgid 65R-C Manual

Ridgid Ikke kategoriseret 65R-C

Læs gratis den danske manual til Ridgid 65R-C (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Ridgid 65R-C, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Threading

1. Inspect the threader before use. Replace dies or any

other part that shows damage or wear. To insure high

thread quality, only use RIDGID replacement dies.

Worn dies can result in poor thread quality

and high handle forces.

2. Mount the pipe firmly in a pipe vise. When threading an

existing pipe, make sure it is secure and will not move.

Cut the end of the pipe cleanly and squarely using a

pipe cutter

(Figure 3)

To prevent tipping, long lengths of pipe

should also be supported with a pipe stand. Vise and

stands should be on level ground.

When working on a scaffold or lift, the oper-

ator should be properly secured to prevent injury in the

event of a fall.

Figure 3 – Cutting End Of Pipe

3. Ream the end of the pipe to remove any burrs that may

have been produced during the cutting of the pipe

(Figure 4)

Figure 4 – Reaming End Of Pipe

4. Adjust thread size for the size pipe to be threaded (refer

to previous instructions for thread size adjustment).

5. Adjust workholder:

65R-C: Turn gauge ring until desired pipe size corresponds

with mark on top of workholder

(Figure 1)

65R-TC: Turn gauge ring until desired pipe size is aligned

with locking cam

(Figure 2)

RIDGID®

5/14

Printed in U.S.A.

EC40741

999-998-280.10

REV. C

RIDGID®65R-C and 65R-TC Threaders are designed to

thread 1" to 2" pipe and conduit using a manually operated

internal ratchet.

Read these instructions carefully before

using this tool. Failure to follow all instructions may

result in property damage and/or serious injury.

Thread Size Adjustment

1. Place threader with workholder up

(Figures 1 and 2)

and unscrew workholder by turning counter-clockwise

until change plate is clear of posts.

2. Move post to desired pipe size. Screw workholder

clock wise until change plate slides over post.

3. Adjust change plate to desired thread size.

Standard Size Thread: Set change plate between the two

“Standard” marks.

Oversize Thread: For oversize (shallow) thread, set change

plate slightly below the “Standard” marks.

Undersize Thread: For undersize (deep) thread, set change

plate slightly above the “Standard” marks.

Figure 1 – 65R-C Threader

Figure 2 – 65R-TC Threader

65R-C & 65R-TC Manual Pipe Threader Instructions

WARNING

Gauge

Ring

Post

Change

Plate

Workholder

Jaw

Clamp

Screw

Standard

Marks

Release Cam

Lever

Gauge

Ring

Workholder

Jaw

Locking

Cam

Change

Plate

Lugs

Post

Workholder

WARNING

10. Apply a generous quantity of RIDGID Thread Cutting

Oil when threading

(Figure 6)

. Use of a lubricating oil

or a poor thread cutting oil can result in a poor quality

cut thread, leaky joints, short die life and high handle

forces.

11. 65R Threaders are jam-proof and will automatically

kick out and disengage the ratchet action when the

thread is complete.

12. Remove threader from pipe by turning release cam

lever to “OPEN” and spin threader back to the “STAN-

DARD” position. Loosen clamp screw or locking cam

and slide threader off the pipe.

Remove by turning the release lever to “OPEN” posi-

tion, loosening clamp screw or locking cam, and

pulling threader straight off pipe. Maintain close control

of the threader so the threads are not damaged.

Spinning the threader back to the “STANDARD” posi-

tion is not required.

NOTE! Clean any oil spill or splatter that is on the ground.

At the end of each job, always clean your threader

and store in a clean dry area to protect against

damage.

Changing Dies

1. Place threader in position as shown in

Figure 1

and

unscrew workholder upwards until change plate is

clear of post. Turn release cam lever to OPEN position.

2. Push post to the left past the 2" mark. Turn the threader

over and remove dies. If the dies stick, tap the ratchet

ring lightly behind the die.

3. Insert new dies making sure die numbers correspond

to the slot numbers. Replace complete die set. Move

post to engage dies.

Failure to replace complete die set may

result in poor thread quality and leaky joints.

4. Turn threader over and set post to desired pipe size.

Screw workholder down so change plate is between

the “Standard” size marks and you are ready to re -

sume threading.

Service and Repair

When servicing this tool, only identical

replacement parts should be used. Failure to follow these

steps may create a risk of serious injury.

If you have any questions regarding the service or repair of

this machine, call or write to:

Ridge Tool Company

Technical Service Department

400 Clark Street

Elyria, Ohio 44035-6001

Tel: (800) 519-3456

E-mail: rtctechservices@emerson.com

6. Turn release cam lever to the “closed” position. Slide

threader on the pipe with the workholder end first

(Fi -

gure 5)

. Center end of pipe in the throat of the dies.

7. Secure workholder on the pipe by tightening the clamp

screw

(Figure 1)

or the locking cam

(Figure 2)

Figure 5 – Sliding Threader Onto Pipe

8. Move the handle in a pumping action to thread the

pipe.

Make sure handle is clean and free from oil

and grease. This allows better control of the tool.

9. When hand threading, your weight should be above

the handle ensuring maximum leverage. If possible, do

not do all the work with you arms; use your weight. Do

not overreach. Keep proper footing and balance to

maintain better control.

Do not slide a pipe or “cheater” over the

handle to gain extra leverage. This practice can result in

serious injury.

NOTE! When using the 65-R Threader with the 300

Power Drive, manually start the thread (approxi-

mately one turn) before starting power drive.

Figure 6 – Applying Thread Cutting Oil

65R-C & 65R-TC Manual Pipe Threader Instructions

WARNING

CAUTION

WARNING

Produkt Specifikationer

Mærke:	Ridgid
Kategori:	Ikke kategoriseret
Model:	65R-C

Har du brug for hjælp?

Hvis du har brug for hjælp til Ridgid 65R-C stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ridgid Manualer

Ridgid 300 Compact Manual

12 Januar 2025

Ridgid K-750 Manual

12 Januar 2025

Ridgid HKO-186 Manual

31 August 2024

Ridgid Raprench 10 Manual

31 August 2024

Ridgid KT-190 Manual

31 August 2024

Ridgid 760 FXP Manual

30 August 2024

Ridgid 700 Manual

30 August 2024

Ridgid micro CA-350 Manual

30 August 2024

Ridgid KWIK-SPIN+ Manual

30 August 2024

Ridgid 690-I Manual

30 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

ENTES GEMO-10-DR-4G Manual

14 Juni 2025

Marshall VAC-12SH Manual

14 Juni 2025

Rane MX 22 Manual

14 Juni 2025

Vulcan VCH88 Manual

14 Juni 2025

Fluke SB140 Manual

14 Juni 2025

Blodgett BCT-101G Manual

14 Juni 2025

Rival 11570 Manual

14 Juni 2025

CDN MT1 Manual

14 Juni 2025

Savage Bros. FireMixer-14 Manual

14 Juni 2025

HMS Premium STR01 Manual

14 Juni 2025