Samsung DVE52A5500V Manual
Samsung
Tørretumbler
DVE52A5500V
Læs nedenfor 📖 manual på dansk for Samsung DVE52A5500V (68 sider) i kategorien Tørretumbler. Denne guide var nyttig for 27 personer og blev bedømt med 4.8 stjerner i gennemsnit af 14 brugere
Side 1/68

Dryer
User manual
DVE(G)55A7700*/DVE(G)55A7300*/DVE(G)52A5500*
Untitled-1 1 2021-04-05 10:16:06

English2
Contents
Contents
Safety information 4
What you need to know about the safety instructions 4
Important safety symbols 4
CALIFORNIA PROPOSITION 65 WARNING 5
Important safety precautions 5
Warnings 8
Cautions 8
Regulatory notice 10
FCC Notice 10
IC Notice 11
Open Source Announcement 12
Installation requirements 13
Key installation requirements 13
Location considerations 13
Ducting requirements 17
Exhausting requirements 18
Gas requirements 19
Electrical requirements 20
Installation 23
What’s included 23
Step-by-step installation 25
Vent blockage test 33
Exhaust ducting guide 35
Switching the door position 36
Before you start 39
Sort and load 39
Functional prerequisite 39
Rack Dry (applicable models only) 40
Untitled-1 2 2021-04-05 10:16:06

English 3
Contents
Operations 42
Control panel 42
Simple steps to start 45
Cycle overview 46
Cycle chart 48
Cycle guide 51
Special features 52
Maintenance 54
Cleaning 54
Troubleshooting 55
Checkpoints 55
Information codes 58
Specications 60
Fabric care chart 60
Protecting the environment 61
Specication sheet 62
Untitled-1 3 2021-04-05 10:16:07

SAVE THESE INSTRUCTIONS
English4
Safety information
Congratulations on your new Samsung dryer. This manual contains important information
on the installation, use and care of your appliance. Please take some time to read this
manual to take full advantage of your dryer’s many benets and features.
What you need to know about the safety instructions
Please read this manual thoroughly to ensure that you know how to safely and efciently
operate the extensive features and functions of your new appliance. Please store the
manual in a safe location close to the appliance for future reference. Use this appliance
only for its intended purpose as described in this instruction manual.
Warnings and Important Safety Instructions in this manual do not cover all possible
conditions and situations that may occur. It is your responsibility to use common sense,
caution and care when installing, maintaining and operating your dryer.
Because the following operating instructions cover various models, the characteristics of
your dryer may differ slightly from those described in this manual and not all warning
signs may be applicable. If you have any questions or concerns, contact your nearest
service center or nd help and information online at www.samsung.com.
Important safety symbols
What the icons and signs in this user manual mean:
WARNING
Hazards or unsafe practices that may result in severe personal injury, death and/or
property damage.
CAUTION
Hazards or unsafe practices that may result in personal injury and/or property damage.
NOTE
Indicates that a risk of personal injury or material damage exists.
These warning signs are here to prevent injury to yourself and others.
Please follow them explicitly.
After reading this manual, store it in a safe place for future reference.
Read all instructions before using the appliance.
As with any equipment that uses electricity and moving parts, potential hazards exist.
To safely operate this appliance, familiarize yourself with its operation and exercise care
when using it.
Safety information
Untitled-1 4 2021-04-05 10:16:07

SAVE THESE INSTRUCTIONS
Safety information
English6
Safety information
6. Before the appliance is removed from service or discarded, remove the door to the
drying compartment.
7. Do not reach into the appliance if the drum is moving.
8. Do not install or store this appliance where it will be exposed to the weather.
9. Do not tamper with internal controls.
10. Do not repair or replace any part of the appliance or attempt any service unless
specically recommended in the user-maintenance instructions or in published user-
repair instructions that you understand and have the skills to carry out.
11. Do not use fabric softeners or products to eliminate static unless recommended by the
manufacturer of the fabric softener or product.
12. Clean the lint screen before or after each load.
13. Do not use heat to dry articles containing foam rubber or similarly textured rubber-like
materials.
14. Keep area around the exhaust opening and adjacent surrounding areas free from the
accumulation of lint, dust, and dirt.
15. The interior of the appliance and exhaust duct should be cleaned periodically by
qualied service personnel.
16. Do not place items exposed to cooking oils in your dryer. Items contaminated with
cooking oils may contribute to a chemical reaction that could cause a load to catch re.
To reduce the risk of re due to contaminated loads, the nal part of a tumble dryer
cycle occurs without heat (cool down period). Avoid stopping a tumble dryer before the
end of the drying cycle unless all items are quickly removed and spread out so that the
heat is dissipated.
17. This appliance must be grounded. See “ ” and “ ” in Electrical requirements Grounding
“Installation” section.
18. Do not allow children to play on or in the appliance. Close supervision of children is
necessary when the appliance is used near children.
19. Do not insert your hand under the dryer.
- This may result in injury.
20. Take care that children’s ngers are not caught in the door when closing it.
- This may result in injury.
21. Control board and inlet valve are intentionally not grounded and may present a risk of
electric shock only during servicing.
- Do not contact this part while appliance is energized.
Untitled-1 6 2021-04-05 10:16:07

SAVE THESE INSTRUCTIONS
English 7
Safety information
WARNING - To reduce the risk of re or explosion:
• Do not dry items that have been previously cleaned, washed, soaked, or spotted with
gasoline, dry cleaning solvents, or other ammable or explosive substances. They
emit vapors that could ignite or explode. Any material that has been in contact with a
cleaning solvent or ammable liquids or solids should not be placed in the dryer until
all traces of these ammable liquids or solids and their fumes have been removed.
There are many highly ammable items used in homes, such as acetone, denatured
alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers,
turpentine, wpees, and wpe removers.
• Items containing foam rubber (may be labeled latex foam) or similarly textured
rubberlike materials must not be dried on a heat setting. Heated foam rubber
materials can, under certain circumstances, produce re by spontaneous combustion.
WARNING - What to do if you smell gas:
• Do not try to light any appliance.
• Do not turn on the appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Clear the room, building or area of all occupants.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the re department.
• Installation and service must be performed by a qualied installer, service agency, or
the gas supplier.
Untitled-1 7 2021-04-05 10:16:07

SAVE THESE INSTRUCTIONS
Safety information
English8
Safety information
Warnings
WARNING
• Ensure pockets are free from small, irregularly shaped hard objects, foreign material,
etc. ie. coins, knives, pins, etc. These objects could damage your dryer.
• Gas leaks may occur in your system, resulting in a dangerous situation.
Cautions
CAUTION
• Do not allow children or pets to play on, in, or in front of the appliance. Close
supervision is necessary when the appliance is used near children and pets.
• Before discarding or removing your dryer from service, remove the door to the drying
compartment to prevent children or animals from becoming trapped inside.
• Do not reach into the appliance when the drum is moving.
• Do not install or store this appliance where it will be exposed to the weather.
• Do not tamper with controls.
• Do not repair, replace, or attempt to service any part of the appliance unless
specically instructed to in the user-repair instructions and you have the
understanding and skills to carry out the procedure.
• Do not use fabric softeners or products to eliminate static unless the softener or
product is recommended for dryer use by the manufacturer of the fabric softener or
product.
• Clean the lint screen before or after each load.
• Keep the area around the exhaust opening and surrounding areas free from lint, dust,
and dirt.
• The interior of the dryer and exhaust duct should be cleaned periodically by qualied
service personnel.
• This appliance must be properly grounded. Never plug the power cord into a receptacle
that is not grounded adequately or not in accordance with local and national codes. See
installation instructions for information about grounding this appliance.
• Do not sit on top of the dryer.
• Do not wash clothing with large buckles, buttons, or other heavy metal or solid objects.
• Gas leaks may not be detected by smell alone.
• Gas suppliers recommend you purchase and install a UL-approved gas detector.
• Install and use in accordance with the manufacturer’s instructions.
Untitled-1 8 2021-04-05 10:16:07

SAVE THESE INSTRUCTIONS
English 9
Safety information
• Do not place items in your dryer that have been spotted or soaked with vegetable oil
or cooking oil. Even after being washed, these items may contain signicant amounts
of these oils.
• Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous
combustion increases when items containing vegetable oil or cooking oil are exposed
to heat. Heat sources such as your dryer can warm these items, allowing an oxidation
reaction in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items
can become hot enough to catch re. Piling, stacking, or storing these kinds of items
may prevent heat from escaping and can create a re hazard.
• All washed and unwashed fabrics that contain vegetable oil or cooking oil can be
dangerous. Washing these items in hot water with extra detergent will reduce, but not
eliminate, the hazard. Always use the Cool Down cycle for these items to reduce their
temperature. Never remove these items from the dryer hot or interrupt the drying
cycle until the items have run through the Cool Down cycle. Never pile or stack these
items when they are hot.
Untitled-1 9 2021-04-05 10:16:07

SAVE THESE INSTRUCTIONS
English10
Regulatory notice
FCC Notice
CAUTION
Any changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of FCC Rules. Operation is Subject to following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received including interference that cause
undesired operation.
For products sold in the US and Canadian markets, only channels 1–11 are available. You
cannot select any other channels.
FCC STATEMENT:
This equipment has been tested and found to comply within the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorienting or relocating the receiving antenna
• Increasing the separation between the equipment and receiver
• Connecting the equipment to an outlet that is on a different circuit than the radio or TV.
• Consulting the dealer or an experienced radio/TV technician for help.
FCC RADIATION EXPOSURE STATEMENT:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated so there is at least 8 inches
(20 cm) between the radiator and your body. This device and its antenna(s) must not be
colocated or operated in conjunction with any other antenna or transmitter.
Regulatory notice
Untitled-1 10 2021-04-05 10:16:07

SAVE THESE INSTRUCTIONS
English 11
Regulatory notice
Unintentional emitter per FCC Part 15
Product type : Clothes Dryers
Model : DVE55A7300*
Responsible Party – U.S. Contact Information
Samsung Electronics America, Inc.
QA Lab America
19 Chapin Rd. Building D Pine Brook NJ 07058
Tel: 1-973-808-6375 Fax: 1-973-808-63
IC Notice
The term “IC” before the radio certication number only signies that Industry Canada
technical specications were met. Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
For products sold in the US and Canadian markets, only channels 1–11 are available. You
cannot select any other channels.
IC RADIATION EXPOSURE STATEMENT:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated so there is at
least 8 inches (20 cm) between the radiator and your body. This device and its antenna(s)
must not be colocated or operated in conjunction with any other antenna or transmitter.
Untitled-1 11 2021-04-05 10:16:07

SAVE THESE INSTRUCTIONS
Regulatory notice
English12
Regulatory notice
Open Source Announcement
The software included in this product contains open source software. You may obtain the
complete corresponding source code for a period of three years after the last shipment of
this product by sending an email to mailto:oss.request@samsung.com.
It is also possible to obtain the complete corresponding source code in a physical medium
such as a CD-ROM; a minimal charge will be required.
The following URL http://opensource.samsung.com/opensource/SMART_AT_051/seq/0
leads to the download page of the source code made available and open source license
information as related to this product. This offer is valid to anyone in receipt of this
information.
NOTE
Hereby, Samsung Electronics, declares that the radio equipment type appliance is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address: The ofcial Declaration of conformity may be
found at http://www.samsung.com, go to Support > Search Product Support and enter the
model name.
Wi-Fi max transmitter power : 20 dBm at 2.412 GHz – 2.472 GHz
Untitled-1 12 2021-04-05 10:16:07

English 13
Installation requirements
Read through the following instructions before installing the dryer, and keep this manual
for future reference.
WARNING
Certain internal parts are intentionally not grounded and may present a risk of electric
shock only during servicing. Service Personnel - Do not contact the following parts while
the appliance is energized: Control board and inlet valve.
Key installation requirements
• A grounded electrical outlet.
• A power cord for electric dryers (except in Canada).
• Gas lines (for gas models) that must meet national and local regulations.
• An exhaust system made of rigid metal or exible stiff-walled metal exhaust ducting.
WARNING
Remove the door from all discarded appliances to prevent a child from suffocating.
Location considerations
• Adequate clearances between the dryer and adjacent walls or other surfaces.
• Adequate air circulation for ventilation and gas combustion.
• Away from water and weather.
WARNING
• Make sure to exhaust the dryer outdoors to reduce the risk of re.
• Keep the dryer area clear of combustible materials, gasoline, and other ammable
vapors and liquids.
• Do not install other fuel-burning appliances around or in the same place as the dryer.
• Place the dryer at least 18 in. (460 mm) above the oor for garage installation.
Installation requirements
Untitled-1 13 2021-04-05 10:16:07

English 15
Installation requirements
Clearance requirement
This clearance requirement is applicable for dryers only.
NOTE
• For washer's clearance requirement, see the washer's user manual.
• If the washer and dryer have different clearance requirements, use the one with the
larger value.
Alcove or closet installations
WARNING
• The dryer must be exhausted to the outside to reduce the risk of re when installed in
an alcove or closet.
• No other fuel-burning appliance should be installed in the same closet as the dryer.
• Place the dryer at least 18 in. (460 mm) above the oor for garage installation.
Minimum clearance for stable operation:
Sides Top Rear Front
1 in. / 25 mm 17 in. / 432 mm 5.9 in. / 150 mm 1 in. / 25 mm
If both the washer and a dryer are installed in the same location, the front of the alcove
or closet must have two unobstructed air openings for a combined minimum total area of
72 in.² (465 cm²).
Untitled-1 15 2021-04-05 10:16:08

Installation requirements
English20
Installation requirements
• Install and use in accordance with the
manufacturer’s instructions.
Electrical requirements
The wiring diagram is located on the plate
under the control panel or rear frame.
WARNING
• Improperly connecting the equipment
grounding conductor can result in a
risk of electric shock. Check with a
qualied electrician or serviceman if
you are in doubt as to whether your
dryer is properly grounded. Do not
modify the plug provided with your
dryer – if it doesn’t t the outlet, have
a proper outlet installed by a qualied
electrician.
• To prevent unnecessary risk of re,
electrical shock, or personal injury, all
wiring and grounding must be done in
accordance with local codes, or in the
absence of local codes, in accordance
with the National Electrical Code, ANSI/
NFPA No. 70-Latest Revision (for the
U.S.) or the Canadian Electrical Code CSA
C22.1 – Latest Revisions and local codes
and ordinances. It is your responsibility
to provide adequate electrical service
for your dryer.
• All gas installations must be done in
accordance with the national Fuel Code
ANSI/Z2231 – Latest Revision (for the
U.S.) or CAN/CGA – B149 Installation
Codes – Latest Revision (for Canada)
and local codes and ordinances.
Grounding
This dryer must be grounded. In the event
of malfunction or breakdown, the ground
will reduce the risk of electrical shock by
providing a path of least resistance for the
electrical current.
Gas models
WARNING
• Your dryer has a cord with an
equipment-grounding conductor and
a grounding plug. The plug must be
plugged into an appropriate outlet that
is properly installed and grounded in
accordance with all local codes and
ordinances.
• Do not modify the plug provided with
your dryer – if it doesn’t t the outlet,
have a proper outlet installed by a
qualied electrician.
• Do not connect the ground wire to
plastic plumbing lines, gas lines, or hot
water pipes.
Untitled-1 20 2021-04-05 10:16:08

English 21
Installation requirements
Electric models
WARNING
• Your dryer has an optional cord with
an equipment-grounding conductor
and a grounding plug. This cord is sold
separately.
• The plug must be plugged into an
appropriate outlet that is properly
installed and grounded in accordance
with all local codes and ordinances.
• Do not modify the plug provided with
your dryer – if it doesn’t t the outlet,
have a proper outlet installed by a
qualied electrician.
• If a power cord is not used and the
electric dryer is to be permanently
wired, the dryer must be connected to
a permanently grounded metal wiring
system, or an equipment grounding
conductor must be run with the circuit
conductors and connected to the
equipment grounding terminal or lead
on the dryer.
Electrical connections
Before operating or testing, follow all
grounding instructions in the “Grounding”
section. An individual branch (or separate)
circuit serving only your dryer is
recommended.
Do not use an extension cord.
Gas models – U.S. and Canada
A 120 volt, 60 Hz AC approved electrical
service with a 15-ampere fuse or circuit
breaker is required.
Electric models – U.S. only
Most U.S. dryers require a 120 / 240 volt,
60 Hz AC approved electrical service.
Some require 120 / 208 volt, 60 Hz
approved electrical service. The electric
service requirements can be found on
the data label located behind the door.
A 30-ampere fuse or circuit breaker on
both sides of the line is required.
• If a power cord is used, the cord
should be plugged into a 30-ampere
receptacle.
• The power cord is not provided with
U.S. electric model dryers. This cord is
sold separately.
Untitled-1 21 2021-04-05 10:16:08

Installation requirements
English22
Installation requirements
WARNING
Risk of Electric Shock
When local codes allow, you can connect
the dryer’s electrical supply with a new
power supply cord kit, marked for use with
a dryer, that is U.L. listed and rated at a
minimum of 120 / 240 volts, 30-amperes
with three No. 10 copper wire conductors
terminated with closed loop terminals,
open-end spade lugs with turned up ends,
or with tinned leads.
• Do not reuse a power supply cord from
an old dryer. The power cord electric
supply wiring must be supported at the
dryer cabinet by a suitable UL-listed
strain relief.
• Grounding through the neutral
conductor is prohibited for (1) new
branch-circuit installations, (2) mobile
homes, (3) recreational vehicles, and
(4) areas where local codes prohibit
grounding through the neutral
conductor. (Use a 4-prong plug for a
4 wire receptacle, NEMA type 14-30R.)
Electric models – Canada Only
A 120 / 240 volt, 60 Hz AC approved
electrical service fused through a
30-ampere fuse or circuit breaker on both
sides of the line is required.
NOTE
All Canadian models are shipped with
the power cord attached. The power cord
should be plugged into a 30-ampere
receptacle. In Canada, you may convert a
dryer to 120 / 208 volts.
Untitled-1 22 2021-04-05 10:16:08

English 23
Installation
This dryer must be installed by a qualied technician. The installer is responsible for
connecting the dryer to the main power while observing the relevant safety regulations of
your area.
What’s included
Make sure all the parts are included in the product package. If you have a problem with
the dryer or the parts, contact a local Samsung customer center or the retailer.
01
02
03 04
05
01 02 03 Control panel Worktop Lint lter
04 05 Door Exhaust duct
Installation
Untitled-1 23 2021-04-05 10:16:09

Installation
English24
Installation
Parts supplied
Y-connector Short water hose
Tools needed for installation
Pliers Cutting knife Pipe wrench (gas
models only)
Nut driver
Level WrenchPhillips screwdriver Duct tape
LPG-safe compound
or Teon Tape (for
gas installation)
WARNING
Packing materials can be dangerous to children. Keep all packing materials (plastic bags,
polystyrene, etc.) out of children’s reach.
Untitled-1 24 2021-04-05 10:16:10

English 25
Installation
Step-by-step installation
Make sure you have a qualied technician install the dryer. Step by step installation
instructions start below.
• Do not remove the protective lm on the door before completing the product
installation. If you remove the protective lm before the installation is complete, the
door may get scratched or damaged during installation.
• Make sure the installation location allows enough space for the dryer door to be fully
open.
STEP 1 Install the exhaust system
1. Select a location and move the dryer to the site. For easy access, we recommend you
install the dryer in the same location as your washer.
2. To change the door direction, see “ ” on page Switching the door position 36.
3. Install the exhaust system as instructed in the “ ” section.Exhaust ducting guide
CAUTION
Before installing your dryer, remove the packing in the duct.
NOTE
• To move the dryer easily, lay two of the carton cushion-from the packaging on the
oor. Tip the dryer on its side so it lies across both cushion-tops. Push the dryer so that
it is near its nal location, and then set the dryer upright.
• Secure room around the dryer to facilitate ducting and wiring.
STEP 2 Connect the gas line (for gas models)
Before connecting the gas line, make sure you have read the “ ” section Gas requirements
on page 19.
1. Remove the protective cap from the gas pipe.
2. Apply an LPG (Liqueed Petroleum Gas)-safe compound or 1.5 wraps of Teon tape to
all threaded connections.
3. Connect the gas supply to the dryer. An additional tting is required to connect
the 3/4” (1.9 cm) female thread end of a exible connector to the 3/8” (1 cm) male
threaded end on the dryer. Tighten up the tting over all threads.
4. Turn on the gas supply, and check for any leaks using a soap solution. If a leak is found,
tighten the connections and try again. Do not use an open ame to check for gas leaks.
Untitled-1 25 2021-04-05 10:16:10

Installation
English26
Installation
STEP 3 Connect the electrical wiring (for electric models)
Before connecting the electrical wiring, make sure you have read the “Electrical
requirements 20” section on page .
3-wire system
A B C L2 L1
D
E
A. External ground connector
B. Neutral grounding wire (white)
C. Center silver-colored terminal block
screw
D. Neutral wire (white or center wire)
E. 3/4” (1.9 cm) UL-listed strain relief
1. Loosen or remove the screws from the
center terminal block.
2. Connect the neutral wire (white or
center wire) of the power cable to the
center, silver-colored terminal screw of
the terminal block. Tighten the screws.
3. Connect the other wires to outer
terminal block screws. Tighten the
screws.
4. Tighten the strain relief screws.
5. Insert the terminal block cover into the
rear panel of the dryer. Then, secure the
cover with a hold-down screw.
CAUTION
• To convert from the 4-wire system
to 3-wire system, connect the ground
strap to the terminal block support to
ground the dryer frame to the neutral
conductor.
• Ring-type terminals are recommended.
If using strap terminals, make sure they
are tightened.
• Connect the power cord and check L1/
L2/N voltage. If the voltage is low, it
may not heat properly. Review the
“Electrical requirements” section on
page 20 if needed.
Untitled-1 26 2021-04-05 10:16:10

English 27
Installation
4-wire system
F
A B C L2 L1
D
E
A. External ground connector
B. Neutral grounding wire (white)
C. Center silver-colored terminal block
screw
D. Neutral wire (white or center wire)
E. ¾” (1.9 cm) UL-listed strain relief
F. Neutral wire (white or center wire)
1. Remove the external ground
connector’s screw and connect the
ground wire (green or unwrapped) of
the power cable to the screw.
CAUTION
- To connect the ground wire to the
neutral position without through
contact A (cabinet ground), contact
a technician. This is not user
serviceable.
- Ring-type terminals are
recommended. If using strap
terminals, make sure they are
tightened.
2. Loosen or remove the screws from the
center terminal block.
3. Connect the neutral wire (white or
center wire) and ground wire (white) to
the center screw of the terminal block.
Tighten the screw.
4. Connect the other wires to the outer
terminal block screws. Tighten the
screws.
5. Tighten the strain relief screws.
6. Insert the tab of the terminal block
cover into the rear slot of the dryer.
Secure the cover with a hold-down
screw.
CAUTION
Connect the power cord and check L1/L2/N voltage. If the voltage is low, it may not heat
properly. Review the “ ” section on page if needed.Electrical requirements 20
Untitled-1 27 2021-04-05 10:16:10

Installation
English28
Installation
WARNING
• All U.S. models are designed for a 3-wire system connection. The dryer frame is
grounded to the neutral conductor at the terminal block. A 4-wire system connection
is required for new or remodeled construction, mobile homes, or if local codes do not
permit grounding through neutral. If you use the 4-wire system, you cannot ground the
dryer frame to the neutral conductor at the terminal block.
• Remove the terminal block cover plate. Insert the power cord with a UL-listed strain
relief through the hole provided in the cabinet near the terminal block.
• A strain relief must be used. Do not loosen the nuts already installed on the terminal
block. Be sure they are tight. Use a 3/8” (1 cm) deep well socket.
• Since january 1, 1996, The national electric code requires that new wiring (not existing)
utilize a 4-wire connection to this dryer.
STEP 4 Connect the water hose
The dryer must be connected to a cold water tap using the provided water hoses.
1. Close the cold water tap. If you have a
washer’s cold water hose attached to
the cold water tap, unscrew and remove
the hose. Then, connect the female end
of the Y-connector to the cold water
tap.
2. Connect the straight end of the water
hose to the Y-connector.
3. Using pliers, tighten the coupling an
additional two-thirds turn. Do not
overtighten because the coupling may
be damaged.
Untitled-1 28 2021-04-05 10:16:10

English 29
Installation
4. Connect the angled end of the water
hose to the lling valve at the bottom
of the rear frame. Turn the coupling
manually until it is tight.
5. Using pliers, tighten the coupling an
additional two-thirds turn. Do not
overtighten because the coupling may
be damaged.
6. If you detached the cold water hose
from your washer, attach the hose
to the open end of the Y-connector,
tighten the coupling by hand until it is
tight, and then, using a pliers, tighten
an additional two-thirds turn.
7. Open the cold water tap, and then check
for any leaks.
If the Y-connector cannot be directly connected to the cold water tap, use the short hose.
See the “ ” section on page Using the short hose as an extension 30.
Untitled-1 29 2021-04-05 10:16:10

Installation
English30
Installation
Using the short hose as an extension
B
A
C
1. Close the cold water tap. If you have a
washer’s cold water hose attached to
the cold water tap, unscrew and remove
the hose. Then, connect the short hose
(B) to the cold water tap. Turn the
coupling by hand until it is tight.
2. Using pliers, tighten the coupling an
additional two-thirds turn. Do not
overtighten because the coupling may
be damaged.
3. Connect the to the Y-connector (A)
brass male end of the short hose. Turn
the coupling by hand until it is tight.
4. Using pliers, tighten the coupling an
additional two-thirds turn. Do not
overtighten because the coupling may
be damaged.
5. Connect the angled end of the water
hoses (C) to the lling valve at the
bottom of the rear frame. Turn the
coupling manually until it is tight.
6. Using pliers, tighten the coupling an
additional two-thirds turn. Do not
overtighten because the coupling may
be damaged.
7. If you detached the cold water hose
from your washer, attach the hose to
the free end of the Y-connector, tighten
the coupling by hand until it is tight,
and then, using a pliers, tighten an
additional two-thirds turn.
8. Open the cold water tap, and then check
for any leaks.
Untitled-1 30 2021-04-05 10:16:10

English 31
Installation
STEP 5 Level the dryer
To ensure optimal performance, the dryer must be level.
A
B
Using a , check if the dryer is level (A)
level side to side and then front to back.
If the dryer is not level, turn the leveling
feet (B) clockwise to lower the dryer or
counterclockwise to raise the dryer.
A B
NOTE
• To set the dryer to the same height
as your washer, fully retract (A)
the leveling feet by turning them
counterclockwise, then the loosen (B)
feet by turning them clockwise. Once
the dryer is the same height as the
washer, follow the directions above to
level the dryer.
• Adjust the leveling feet only as much as
necessary to level the dryer. Extending
the leveling feet more than necessary
can cause the dryer to vibrate.
Untitled-1 31 2021-04-05 10:16:11

Installation
English32
Installation
STEP 6 Power on (for gas models)
Make sure all gas connections, the exhaust line, and all wiring is connected correctly. Then,
plug the power cord into a power source and check the dryer’s installation and operation
using the nal checklist in Step 7 below.
STEP 7 Final check
When installation is complete, conrm that:
• The dryer is plugged into an electrical outlet and grounded properly.
• The exhaust ductwork is connected, and the joints are taped.
• You have used rigid or stiff-walled exible metal duct material, not plastic exible duct.
• The dryer is level and is sitting rmly on the oor.
• The dryer starts, runs, heats, and shuts off properly.
For gas models:
• The gas is supplied properly with no leaks (For gas models only).
CAUTION
The burner may not ignite initially due to air in the gas line. Allowing your dryer to
operate on a heat setting will purge the line. If the gas does not ignite within 5 minutes,
turn your dryer off and wait 5 minutes. Be sure the gas supply to your dryer has been
turned on. To conrm gas ignition, check the exhaust for heat.
Untitled-1 32 2021-04-05 10:16:11

Installation
English34
Installation
• If the test result displays check code (the duct system is blocked ), refer to the “Ducting
requirements 17” section on page and the “ ” section below, and Exhaust ducting guide
then take proper measures to correct any problems. If the test is suspended, it could
result in incorrect results. Follow the proper procedures when testing the dryer.
• Even if the test result is normal (“End or ”), the duct system could be blocked slightly. 0
Properly install all duct work according to the installation instructions in this manual.
Installation check codes
Check code Meaning Solution
0Vent condition is good.
Clg (Cg) The vent is clogged. 1. Clean the lint lter.
2. Check your vent condition. (Refer
to the “Ducting requirements”
section)
* You must take measures (such as
cleaning) through expert personnel.
C80 (C8)
About 80 % of the vent is clogged.
(This may decrease the drying
performance.)
C90 (C9)
Over 90 % of the vent is clogged.
(This may lead to poor drying
performance or cause malfunction)
Ct
The internal temperature of the
dryer is too low (below 32 °F (0 °C))
or too high (over 104 °F (40 °C)) and
therefore vent blockage cannot be
detected.
Leave the dryer at room
temperature (41~95 °F (5~35 °C))
for an hour and check again.
tC Temperature sensor error Contact a service center.
C1
Unit is detecting items inside the
drum or there is an error on the dry
sensor.
Remove items from the drum and
check again.
If the problem continues, contact a
service center.
dC Unit is detecting door is open
Close the door properly and check
again.
If the problem continues, contact a
service center.
9C1 Abnormal voltage detected
Check the power connection. (Refer
to the “Connect the electrical wiring
(for electric models)” section)
If the problem continues, contact a
service center.
Untitled-1 34 2021-04-05 10:16:11

Installation
English36
Installation
Switching the door position
To reverse the direction of the door, we
recommend that you contact a qualied
technician.
1. Put a soft rug on the oor to rest the
door on after you have removed it.
This will prevent the door from being
scratched.
2. Unplug the power cord of the dryer.
3. Remove the four hinge screws from
the door, and then remove the door by
lifting it up slightly.
4. Remove the two screws from the lever
holder, and then remove the holder
cover.
5. Put the lever holder on the other side
as shown, and then tighten the screws.
Install the holder cover on the opposite
side as shown.
6. Use a at-head screwdriver to remove
the two hinge covers from the original
side. Install the hinge covers on the
opposite side as shown.
Untitled-1 36 2021-04-05 10:16:12

Installation
English38
Installation
12. Reinstall the door on the front frame,
and then carefully insert and tighten
the 4 hinge screws.
Untitled-1 38 2021-04-05 10:16:12

Before you start
English40
Before you start
Rack Dry (applicable models only)
Some models come with a drying rack which is inserted into the drum at the factory. If
your model came with a drying rack, remove the rack from the drum before you use the
dryer for the rst time. To remove the rack, pull the rack straight up, and then take it out
of the drum. Remove the drying rack from its packaging and store the rack for later use.
A
If a drying rack is not provided, you can
purchase it at a local Samsung service
center. (Part Code : DC93-00374H)
To use the drying rack, follow these steps:
1. Insert the inside the drying rack (A)
tumbler with the lter handle to the
front.
2. Insert the rear legs of the drying rack
into the recessed areas of the rear wall,
and then press down the middle of the
drying rack to secure it in place.
3. Put items to dry on the rack. Make sure
to leave space between the items for air
ow.
4. Press Rack Dry or other Cycle Setting
according to rack drying suggestions
below, then select the drying time.
5. When the items are dry, remove the
them from the dryer, and then remove
the drying rack.
Untitled-1 40 2021-04-05 10:16:13

English42
Operations
WARNING
To reduce the risk of re, electric shock, or injury to persons, read the “Safety information”
before operating this appliance.
Control panel
DVE(G)55A7****
02
01
03 04 05 06
07
08
09
12
13
10
11
DVE(G)52A5****
02
01
03 04 05 06
07
08
09
12
13
10
11
01 Cycle Selector
Turn the Cycle Selector to select a desired cycle. When a cycle is
selected, the cycle indicator lights up.
• Steam Cycles: The dryer sprays water into the drum to
deodorize clothes and reduce static electricity and wrinkles.
• Manual Dry: The drying time is xed.
02 Digital Graphic
Display
Displays all cycle information, including the cycle time,
information code, and operating status.
Operations
Untitled-1 42 2021-04-05 10:16:14

Operations
English44
Operations
08 Damp Alert
This alert is available for all Sensor Dry cycles except for
ACTIVEWEAR. Available dry levels are Normal, More, and Extra.
If a load contains mixed fabrics, the Damp Alert indicator blinks
when average dryness of the items in the load is 80 % dry. This
lets you take items that you don’t want fully dried or that dry
quickly out of the dryer early while letting others continue to
dry.
09 Drum Light
Press to turn the interior lamp on or off. The lamp stays lit for 2
minutes after it has turned on, regardless of whether the power
is on or off or the door is open or closed, and then turns off
automatically.
10 Adjust Time
You can change the set time in the Manual Dry cycles. (QUICK
DRY, TIME DRY AIR FLUFF, and ) To change the cycle time, press
or until the desired time is displayed.
11 Smart Control
After connecting the Tumble Dryer to your home network using
the SmartThings app, you can control or monitor the dryer
remotely. When started, the Smart Control (Smart Monitor)
indicator blinks. The dryer enters waiting mode and waits for
remote commands.
12 Power Press to turn on/turn off the dryer.
13 Start/Pause (Hold
to Start) Press to start or stop operation.
NOTE
Do not take extremely tangled items from your washer and put them into the dryer. They
can degrade the drying efciency of the dryer or cause the door to open. We recommend
that you untangle the items before putting them into the dryer. Also, do not put objects on
the dryer, especially on the control panel.
CAUTION
Do not spray water directly onto the control panel. This may cause a system failure.
Untitled-1 44 2021-04-05 10:16:14

English 45
Operations
Icon description
Sensor Dry This icon appears when the dryer operates the cycle which
senses the internal humidity to determine the drying time.
Filter Check
This icon displays after every load as a reminder to clean
the lint lter. Clean the lint lter before every cycle and
make sure the lter is properly inserted before starting a
cycle.
Vent Sensor
(DVE(G)55A7****
models only)
The dryer features a vent sensor that detects and noties
you when it is time to clean the ductwork. The indicator
lets you know the status of the duct.
Steam
This icon appears when the dryer is in steam process. The
dryer sprays water into the drum to deodorize clothes and
reduce static electricity and wrinkles.
Child Lock This icon indicates that Child Lock is on. For more
information on Child Lock, see page 52.
Alarm Off This icon indicates that the alarm is off. For more
information on Alarm Off, see page 52.
Wi-Fi This icon indicates that the dryer is connected to Wi-Fi.
Simple steps to start
1. Press Power to turn the dryer on.
2. Turn the to select a cycle. Cycle Selector
3. Change the cycle settings ( , and ) as necessary. Dryness Temp., Time
4. Select desired options as necessary.
5. Press and hold Start/Pause (Hold to Start).
To change the cycle during operation
1. Press Start/Pause (Hold to Start) to stop operation.
2. Select a different cycle, and repeat steps 2-4 above if necessary.
3. Press and hold again to start the new cycle. Start/Pause (Hold to Start)
Untitled-1 45 2021-04-05 10:16:15

Operations
English46
Operations
Cycle overview
Standard Cycles
Cycle Description
NORMAL
For most fabrics including cottons and linens.
If NORMAL is selected, the Eco Dry function is enabled by
default. For more information, see Eco Dry in the “Control panel”
section.
HEAVY DUTY For drying items made out of heavy fabrics, such as jeans,
corduroys, or work clothes, with high temperature heat.
BEDDING For bulky items such as blankets, sheets, and comforters.
PERM PRESS For drying wrinkle-free cottons, synthetic fabrics, knits, and
permanent press fabrics automatically.
DELICATES For heat-sensitive items at a low drying temperature.
ACTIVEWEAR
For exercise wear and outdoor wear such as sports jerseys,
training pants, water-repellent jackets, and other performance
clothing.
Thick fabrics like a zipper or velcro closure of a jacket, or
training socks may not be completely dried.
DOWNLOADED
• Select to choose from more cycles available on the
SmartThings app on your smartphone.
• Available cycles: ECO NORMAL, SHIRTS, DENIM, TOWELS,
RACK DRY, WRINKLE AWAY
• Factory setting: WRINKLE AWAY
Untitled-1 46 2021-04-05 10:16:15

Operations
English48
Operations
Cycle chart
NOTE
For best results, follow the load size recommendations for each dry cycle.
• Large load: Fill the drum to about 3/4 full. Do not add items over this level as they
need to tumble freely.
• Medium load : Fill the drum to about 1/2 full.
• Small load : Fill the drum with 3-5 items, not more than 1/4 full.
Cycle Recommended items Load size Dry level
NORMAL Cottons, work clothes, linens, mixed loads Normal dry
(Adjustable)
HEAVY DUTY Heavy fabrics such as jeans, corduroys, heavy work
clothes
Normal dry
(Adjustable)
BEDDING Bulky items such as blankets, sheets, comforters,
pillows
Normal dry
(Adjustable)
DELICATES Underwear, blouses, lingerie Normal dry
(Adjustable)
PERM PRESS Shirts, synthetic fabrics, knits, wrinkle-free cottons,
permanent press
Normal dry
(Adjustable)
ACTIVEWEAR Water-repellent wear, performance clothes, sports
wear (Maximum : 4 lbs)
Normal dry (Not
adjustable)
QUICK DRY Small loads -
TIME DRY Any load -
AIR FLUFF Foam,rubber, plastic -
STEAM SANITIZE Bedding, curtains, children's clothing Very dry (Not
adjustable)
REFRESH Shirts, trousers, comforters, pillows -
Untitled-1 48 2021-04-05 10:16:16

English 49
Operations
NOTE
: factory setting, : can be selected
Cycle
Functions (Temp. Control)
Time
High Low
NORMAL
HEAVY DUTY
BEDDING
DELICATES
PERM PRESS
ACTIVEWEAR
QUICK DRY
TIME DRY
AIR FLUFF
STEAM SANITIZE
REFRESH
Untitled-1 49 2021-04-05 10:16:17

English 51
Operations
Cycle guide
The best way to dry items is to follow the instructions on the care label. If no drying
instructions are provided, see the following table for reference.
Cycle Description
Bedspreads &
Comforters
Follow the care label instructions or dry using BEDDING.
• Make sure the item is thoroughly dry before using or storing.
• May require repositioning in the drum to ensure even drying.
Blankets
Use NORMAL and dry only one blanket at a time for best
tumbling action.
• Make sure blankets are thoroughly dry before using or
storing.
Curtains & Draperies
Use PERM PRESS and the Medium temperature setting to help
minimize wrinkling.
• Dry curtains and draperies in small loads for best results and
remove as soon as possible.
Cloth Diapers Use NORMAL and the Medium temperature setting for soft,
uffy diapers.
Down–lled Items
(jackets, sleeping
bags, comforters, etc.)
Use NORMAL and the Medium temperature setting.
• Add a couple of dry towels to absorb moisture and shorten
drying time.
Foam Rubber (rug
backs, stuffed toys,
shoulder pads, etc.)
Do not dry on a heat setting.
WARNING
Drying a rubber item with heat may damage it or cause a re.
Pillows
Use NORMAL.
• Add a couple of dry towels and a pair of clean sneakers to
help the tumbling action and to uff the items.
• Do not dry kapok or foam pillows using a heated drying
cycle.
Plastics (shower
curtains, outdoor
furniture covers, etc.)
Use TIME DRY and the Low or Extra Low temperature settings
depending on the care label instructions.
WARNING
Do not dry:
• Fiberglass items (curtains, draperies, etc.)
• Woolens, unless recommended on the label
• Items spotted or soaked with vegetable or cooking oils
Untitled-1 51 2021-04-05 10:16:17

English 55
Troubleshooting
Checkpoints
If the dryer operates abnormally, rst check the list of problems in the table below and
try the suggested actions.
Problem Action
Does not run.
• Make sure the door is latched shut.
• Make sure the power cord is plugged into a live electrical
outlet.
• Check your home’s circuit breakers or fuses.
• Press or tap again if the door is Start/Pause (Hold to Start)
opened during a cycle.
• Clean the lint lter.
Does not heat.
• Check your home’s circuit breakers or fuses.
• Some cycles do not require heating. Check the selected
cycle again.
• For a gas dryer, make sure the gas supply is on.
• Clean the lint lter and exhaust duct.
• The dryer may have moved into the cool-down phase of
the cycle.
• Turn off the Eco Dry option for the NORMAL or TIME DRY
cycles. When the Eco Dry option is on, the dryer performs
an air dry process in the beginning of the cycle to reduce
energy consumption. The air dry process does not use
heated air, so you may feel that the dryer is not being
heated, but this is normal.
Troubleshooting
Untitled-1 55 2021-04-05 10:16:18

English 57
Troubleshooting
Problem Action
Has odors.
• Household odors from paint, varnish, strong cleaners, etc.
may enter the dryer with the surrounding room air. This is
normal as the dryer draws the air from the room, heats it,
pulls it through the tumbler, and exhausts it outside.
• When these odors linger in the air, completely ventilate the
room before using the dryer.
• Use a cycle featuring the Refresh function. If odors persist,
wash and dry the item again.
• Use the REFRESH cycle. If odors persist, wash and dry the
items again.
Lint on clothes.
• Make sure the lint lter is cleaned before every load. For
clothes that naturally build up lint, clean the lter during
the cycle.
• Some fabrics are lint producers (for example, a fuzzy white
cotton towel) and they must be dried separately from
clothes that are lint trappers (for example, a pair of black
linen pants).
• Divide larger loads into smaller loads for drying.
• Check pockets thoroughly before drying, then dry clothes.
• Remove lint inside the drum before drying.
Items still wrinkled
after WRINKLE
PREVENT (WRINKLE-
CARE, WRINKLE
RELEASE).
• Small loads of 1 to 4 items work best.
• Load fewer items. Load similar-type items.
• Take out the items immediately after drying is complete.
Water drips from the
nozzle when STEAM
CARE starts.
• This is steam condensation. The dripping water will stop
after a short time.
Sprayed water is not
visible during STEAM
CARE.
• Sprayed water is difcult to see when the door is closed.
Extended time.
• Sensor Dry automatically senses the moisture in the load
and shuts the dryer off when the selected dryness level is
reached. The drying time can change according to the type
and amount of laundry. See the cycle chart for reference.
If a problem persists, contact a local Samsung service center.
Untitled-1 57 2021-04-05 10:16:18

Troubleshooting
English58
Troubleshooting
Information codes
If the dryer fails to operate, you may see an information code on the display panel. To
determine what you should do, check the list of codes in the table below, and then try the
suggested actions.
Code Action
dC
Operating the dryer with the door open.
• Make sure the door is properly closed.
• Make sure laundry is not caught in the door.
FC
Invalid power source frequency.
• Try restarting the cycle.
• If this information code remains, contact a Samsung service
center.
AC Electronic control problem (Invalid Communication).
• Contact a Samsung service center.
HC
High temperature heating check
• Clean the lint lter.
• If this information code remains, contact a Samsung service
center. (enter the line test mode)
9C1
The electronic control needs to be checked.
• Check if power cord is connected properly.
• Check if the electrical outlet is working properly.
• If the information code remains, contact a Samsung service
center.
tC
The Thermistor1 resistance is very low or high.
• Check for a clogged lint screen
• Check if the vent system is restricted.
• If this information code remains, contact a Samsung service
center.
tC5
The Thermistor2 resistance is very low or high.
• Check for a clogged lint screen.
• Check if the vent system is restricted.
• If this information code remains, contact a Samsung service
center.
dF Incorrect door switch.
• Contact a Samsung service center.
Untitled-1 58 2021-04-05 10:16:18

English 59
Troubleshooting
Code Action
3C The PBA needs to be checked.
• Unplug the power plug and contact a Samsung service center.
If any information code keeps appearing on the display, contact a Samsung service center.
Untitled-1 59 2021-04-05 10:16:18

English60
Specications
Fabric care chart
The following symbols provide garment
care direction. The clothing care labels
include symbols for drying, bleaching,
drying and ironing, or dry cleaning when
necessary. The use of symbols ensures
consistency among garment manufacturers
of domestic and imported items. Follow
care label directions to optimize garment
life and reduce laundering problems.
Wash cycle
Normal
Permanent press / Wrinkle
resistant / Wrinkle control
Gentle / Delicates
Hand wash
Water temperature
Hot
Warm
Cold
NOTE
The Water Temperature table lists
appropriate wash water temperatures for
various items. The temperature range is
106-126 °F (41-52 °C) for Hot, 84-106 °F
(29-41 °C) for Warm, and 61-84 °F (16-
29 °C) for Cold. (Wash water temperature
must be a minimum of 61 °F (16 °C)
for detergent activation and effective
cleaning.)
Bleach
Any bleach (when needed)
Only non-chlorine (color-safe)
bleach (when needed)
Tumble dry
Normal
Permanent press / Wrinkle
resistant / Wrinkle control
Gentle / Delicates
Special instructions
Line dry / Hang to dry
Drip dry
Dry at
Heat setting
High
Medium
Low
Any heat
No heat / Air
Specications
Untitled-1 60 2021-04-05 10:16:21

English 63
LIMITED WARRANTY (U.S.A.)
SAMSUNG DRYER
LIMITED WARRANTY TO ORIGINAL CONSUMER PURCHASER WITH PROOF OF
PURCHASE
This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS
AMERICA, INC. (SAMSUNG) and delivered new, in the original carton to the original
consumer purchaser, is warranted by SAMSUNG against manufacturing defects in
materials or workmanship for the limited warranty period, starting from the date of
original purchase, of:
One (1) Year All Parts and Labor
This limited warranty is valid only on products purchased and used in the United States
that have been installed, operated, and maintained according to the instructions attached
to or furnished with the product. To receive warranty service, the purchaser must contact
SAMSUNG at the address or phone number provided below for problem determination and
service procedures. Warranty service can only be performed by a SAMSUNG authorized
service center. The original dated bill of sale must be presented upon request as proof
of purchase to SAMSUNG or SAMSUNG’s authorized service center to receive warranty
service.
SAMSUNG will provide in-home service within the contiguous United States during the
warranty period at no charge, subject to availability of SAMSUNG authorized servicers
within the customer’s geographic area. If in-home service is not available, SAMSUNG may
elect, at its option, to provide transportation of the product to and from an authorized
service center. If the product is located in an area where service by a SAMSUNG
authorized servicer is not available, you may be responsible for a trip charge or required
to bring the product to a SAMSUNG authorized service center for service.
To receive in-home service, product must be unobstructed and accessible to the service
agent.
During the applicable warranty period, a product will be repaired, replaced, or the
purchase price refunded, at the sole option of SAMSUNG. SAMSUNG may use new
or reconditioned parts in repairing a product, or replace the product with a new or
reconditioned product. Replacement parts and products are warranted for the remaining
portion of the original product’s warranty or ninety (90) days, whichever is longer. All
replaced parts and products are the property of SAMSUNG and you must return them to
SAMSUNG.
Untitled-1 63 2021-04-05 10:16:22
Produkt Specifikationer
Mærke: | Samsung |
Kategori: | Tørretumbler |
Model: | DVE52A5500V |
Har du brug for hjælp?
Hvis du har brug for hjælp til Samsung DVE52A5500V stil et spørgsmål nedenfor, og andre brugere vil svare dig
Tørretumbler Samsung Manualer

10 Februar 2025

13 Januar 2025

2 Januar 2025

30 December 2025

12 November 2024

12 November 2024

13 Oktober 2024

14 September 2024

5 September 2024

5 September 2024
Tørretumbler Manualer
- Tørretumbler Taurus
- Tørretumbler MPM
- Tørretumbler Kernau
- Tørretumbler VOX
- Tørretumbler Gaggenau
- Tørretumbler Smeg
- Tørretumbler Salora
- Tørretumbler Küppersbusch
- Tørretumbler Black And Decker
- Tørretumbler Gemini
- Tørretumbler Sauber
- Tørretumbler CDA
- Tørretumbler TESLA Electronics
- Tørretumbler Siemens
- Tørretumbler Westinghouse
Nyeste Tørretumbler Manualer

10 Juni 2025

10 Juni 2025

10 Juni 2025

10 Juni 2025

10 Juni 2025

10 Juni 2025

10 Juni 2025

9 Juni 2025

9 Juni 2025

9 Juni 2025